Thank you for purchasing our dehumidifier. wishes that our products and services can bring convenience to your work and life. We highly recommend that you keep the manual for reference if you encounter unexpected events using the unit. Please read the manual carefully to ensure proper use of the dehumidifier. Our dehumidifiers are widely used in family bedrooms, bathrooms, base meets, offices and storage rooms, etc.
BEFORE FIRST USE: To prevent any internal damage, it is very important to keep the unit {like this one) upright throughout its journey. Please leave it standing as the picture shown below and outside the box for 24 HOURS before plugging it in.
Safety Instructions. Parts Description Control Interface Operation Instructions Cleaning & Maintenance. Troubleshooting Special Notes Technical Parameters Warranty & Contact Us Statement The graphics and functions provided in this manual may not be the same as the actual product. Please always refer to the actual product. The model of the machine on the manual is for reference only, please check the corresponding content and operate the machine based on the actual product.
Before cleaning the dehumidifier, tum off the power and unplug it from the power outlet, Please do not place the machine near heat or flammable dangerous goods. Do not insert your fingers or sticks into the air inlet or outlet. Always keep the machine on even surfaces, avoid placing the machination or sloping ground. Do not spray water, insecticides or flammable liquids on the unit. This machine should not be placed in a confined and narrow space.
\ o ooo EEN liaise 53 Fiftieth) TIMER LIGHTING SPEED POWER LOCK SETTING DISPLAY PANEL Timer Button Power Button «© Press to Initiate the auto start (1) Presto nm te chumminess oF auto Stop feature, tonal a Tne 101 Setting Bunion AEH ant Control the hu get stein he cont panel Wil Continental inky setting Lighting Button Speed Button ¥ Control the ED panels light 5 Control the fan speed oni
Setting Humidity The humidity level can be set within a range of 30%RH to 80%RH in 5% increments. When it starts to work, it will first automatically detect and show the room's humidity. In humidification mode (other modes are invalid), press the "SETTING" button, you can change the humidity selection in 5% increments, " " will flash and show the setting humidity. When the humidity level is higher or drops to the level you have set, the dehumidifier will automatically begin to work or stop.
Speed Button Control the fan speed. Press to select either FAST or SLOW fan speed. FAST fan speed will result in quicker moisture removal. Set the speed FAST for maximum moisture removal. When the humidity has been reduced and quiet operation is more preferred, set the fan speed back to SLOW. Light Function Setting 1. In the power on status, press the "LIGHTING" button to turn on or turn off the back light; 2.
Auto Defrost Feature When the dehumidifier is running at a lower temperature, the system will automatically determine whether there is a presence of frost. If any frost exists, it will defrost automatically. Defrost Action The fan runs at high wind speed when the compressor stops. When the device is currently powered on, before any operation, only the "POWER" indicator will be on indicating the device is in "Standby" status.
The dehumidifier can be used for drying clothes in rainy weather. Step 1. Hang the washed clothes in a small space such as cloakroom, bathroom, or storage room. Note: Keep away the unit from the water drip of the washed clothes. Step 2. Open the dehumidifier and set the humidity level at 30%RH. It is best if you let the air outlet of the dehumidifier to blow air to the clothes directly. 1. The drying effect will vary from the thickness of clothes, the number of clothes and the size of the drying space.
Humidly always shows “25% RH" —but theta is a big difference from the actual humidity. Humidity sensor failure? Set the humidity to 30%RH, the dehumidifier ‘an stl continue to work, and can be used normally. Repair and replace the humidity sensor. the actual humidity. Water on the surface of humidity sensor? The dehumidifier la not affected and can ‘continue to work, and can be used normally. Plagues let the dehumidifier sap working for a period of tine, after the water on the.
Two ways are available to remove the collected water. Use the Water Tank When the water tank is already full, the Full Tank Alert indicator will light up, the dehumidifier will automatically shut down until the tank has been emptied and placed back to the unit.
Note: Do not remove the float from the water tank. If the float in the water tank is removed, the sensor may not be able to determine the water level stored in the tank properly that may lead to water overflow leak from the water tank. If the water tank is dirty, just use cold water or warm water to clean it. Do not use detergent, steel wool, chemically treated dust cloth, gasoline, benzene, thinner or other solvents. Otherwise, it may damage the water tank and cause it to leak.
Remove the power supply, use a knife or pliers and other tools to remove the plastic cover of the continuous drainage port and insert the water hose into the port. Connect the power supply to start the operation. The outlet of the water hose should be lower than the continuous drainage port by more than 3.9 inches, and can not be bent. {Note: The diameter of continuous drainage port is 0.63 inches.) Insert the water hose nto the continuous drainage port.
Turn the dehumidifier off and remove the plug from the wall outlet before cleaning. A Cleaning the dehumidifier body Please use only a soft and a bit wet textile or cloth to clean iit. B Cleaning filter Pull out the filter. Clean the filter: Use a vacuum cleaner to gently remove the dust from the surface of the filter. If the filter is very dirty, wipe it with warm water and a mild detergent and dry it completely. Slowly insert the filter back into the fuselage.
Check the information below for troubleshooting steps. It will save you time to resolve issues that may happen with the unit. The list includes most of the common cases, but not the results of defective units, crafts or materials in the unit. If all troubleshooting steps have been exhausted and the issue is still occurring, please feel free to reach out to Keynotes Customer Service to get further assistance. lem use | Make sure that the unit's plug The power cord Is unplugged.
‘This is to prevent the frequent start of the machine. Does the machine stop working just now? Please wait for more than 3 minutes. Room humidity is low. The dehumidifier is designed to work in the humidity range of Above or below this range, it will not work. Dehumidifier does not dry the air as it should The air filter Is dirty. Clean the air filter. Is the air inlet or air outlet Remove the obstruction from obstructed? the alr inlet or outlet.
The dehumidifier is not Move the machine toa positioned levelly. horizontal position. Is there blocking around the The dehumidifier makes loud | air inlet? Clean up the dirt or dint on noise when operating The air filter is clogged. " Please check whether the Is the filter installed cling bag of the filter had correctly? n removed and the filter has been installed correctly. Check if the dehumidifiers in | D0 Not set the humidity too Continuous Mode. low.
When using, please do not put Do not insert thin rods and hard When using, please keep the the machine at the soft and objects into the fuselage to machine away from heating uneven ground, avoid vibration avoid malfunction and danger. fum ace, electric kettle and and movement. Thor heat sources. When using, make sure doors Please do not put objects around If do not use the product fora and windows are closed to get the bad.
MODEL PD220B POWER SOURCE 120V ~ 60Hz RATED POWER (95°F, 90%RH) 400W RATED CURRENT (95°F, 90%RH) 3.6A MOISTURE REMOVAL (65°F, 60%RH) 12.3 Pints/Day MOISTURE REMOVAL (80°F, 60%RH) 20 Pints/Day MOISTURE REMOVAL (86°F, 80%RH) 43 Pints/Day MOISTURE REMOVAL (95°F, 90%RH) 60 Pints/Day INPUT POWER (65°F, 60%RH) 235W INPUT CURRENT (65°F, 60%RH) 222A IEF (65°F, 60%RH) 1.30 liters/kWh MOTOR FLA 047A MOTOR COMPRESSOR REFRIGERANT (200g) MAXIMUM ALLOWABLE PRESSURE 363PSIG (2.5MPa) HIGH PRESSURE 232PSIG (1.
Keynotes offers a 12-month warranty to all of our products together with the original proof of purchase when a defect occurred, including those newly purchased and unused, from Keynotes or through an authorized reseller, wholly or substantially, or as result of faulty manufacturing parts, or workmanship during the Warranty Period.