CD PLAYER DPF-R 6030 DPF-R 4030 DPF-R 3030 CD-406 CD-404 CD-403 INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is used to describe multiple models listed above. Model availability and features (functions) may differ depending on the country and sales area. DTS disclaimer clause When playing DTS-encoded CDs, excessive noise will be exhibited from the analog stereo outputs.
Before applying power Caution : Read this page carefully to ensure safe operation. Units are designed for operation as follows. 2 U.S.A. and Canada ................................................................... AC 120 V only Australia .................................................................................... AC 240 V only Europe and U.K. ........................................................................ AC 230 V only China and Russia ................................................
Before applying power Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage.
System connections 4 Malfunction of microcomputer Caution: If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”. £ Do not plug in the power lead until all connections are completed. Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Digital component (MD, DAT, etc.
System connections System control connections Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. This unit is compatible only with the [SL-16] mode. The system control operation is not available if the unit is connected in the [XS-8] connection mode. Amplifier or receiver SYSTEM CONTROL This unit SYSTEM CONTROL If your component has the mode select switch, set the connected components to the [SL16] mode.
Controls and indicators 6 CD-406/DPF-R6030 Play indicator (The displays given in this manual are approximations only. They may differ from what actually appears on the display.) Text information display Pause indicator CD-404/403/DPF-R4030/R3030 Program check indicator EDIT indicator RANDOM indicator Program mode indicator REPEAT indicator FILE RANDOM AUTO PAUSE PGM Play indicator Pause indicator 1 2 MULTI EDIT A 3 4 Music calendar (1 ~ 20) P.C. DISC NO. B REPEAT TRACK NO.
Controls and indicators 7 The keys with the same name as those on the remote control unit operate the same way as the remote control unit. 1 ON/STANDBY (POWER / ) key 9 Turns the unit ON/STANDBY. 2 P.MODE key # $ % @ @ Disc tray 9 # Search (1/¡) keys ! Fast forwards or fast reverses the track. $ DISC SKIP key 9 Press to rotate the disc tray or to select the disc. Press to skip to the beginning of another track.
Operation of remote control unit (Except for CD-403/DPF-R3030) The keys with the same name as those on the main unit operate the same way as on the main unit. The keys marked * are provided only on the remote control unit. 8 POWER DISC SELECTOR 1 DISC SELECTOR keys 2 DISC SKIP key 0 9 *4 OUTPUT (DOWN, UP) keys 5 5 POWER key 1 1 2 3 2 4 5 6 3 7 8 9 4 P.MODE 0 +10 5 EDIT CLEAR CHECK SKIP TIME DISP. REPEAT RANDOM 3 Program-related and other keys RANDOM key ^ REPEAT key & P.
Preparing to play tracks Preparation • Turn the unit ON. 9 Press the ON/STANDBY (POWER / )key. POWER ON/STANDBY Loading/unloading discs 1 Load/unload a disc. 1 Open the tray. OPEN/CLOSE 2 Place/remove a disc. ÷ Do not touch the played side of disc. Label side Disc tray 3 When loading or unloading other discs DISC SKIP 2 Close the tray. ÷ When loading/unloading a disc while the tray rotates, a malfunction might occur. Load/unload the disc when the tray does not rotate.
Normal play (TRACK mode) 10 Use the following procedure to play a CD in the original order of tracks from track No. 1. Playing tracks in order from track No. 1 1 Check that the unit is in the TRACK mode.! CD-406/DPF-R6030 2 Start playback. If there is no disc in the selected disc tray, the corresponding " goes off. indicator " DISC 1 Select the disc. DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 2 DISC 3 DISC 4 DISC 5 Blinks during playback.
Normal play (TRACK mode) 11 Playback from desired track 1 Select the disc. DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 2 Select the desired track No. Main unit Remote control unit 1 2 3 4 5 6 7 8 9 0 +10 Press the numeric keys as shown below.... To enter track No. 23 : +10, +10, 3 To enter track No. 40 : +10, +10, +10, +10, 0 ÷ Playback starts from the selected track and continues on the subsequent tracks.
Displays 12 You can select the display type and check the disc information. Preparation ÷ Load a disc in the CD player. Each press the TIME DISP. key, the display changes as follows: CD-406/DPF-R6030 TIME DISP. During playback: 1 Track title (Only when the current disc is a CD TEXT disc.) CD-404/403/DPF-R4030/R3030 During playback: 2 Elapsed time of the track now playing 1 Elapsed time of the track now playing FILE RANDOM AUTO PAUSE PGM 1 2 3 MULTI EDIT A DISC NO. B 4 REPEAT TRACK NO.
Programmed play (PGM mode) Use the following procedure to program desired tracks in a desired order. (up to 32 tracks) Preparation 13 ÷ Load a disc in the CD player. 1 Press so that the “PGM” indicator lights. Blinks. CD-406/DPF-R6030 Do this operation in the stop mode. P.MODE CD-404/403/DPF-R4030/R3030 Light up. FILE RANDOM AUTO PAUSE PGM 2 1 2 3 MULTI EDIT A 4 B 5 Program desired tracks. 1 Select the disc.
Programmed play (PGM mode) 14 To stop playback ÷ The programmed contents remain in memory. To check or change the programmed tracks CD-406/DPF-R6030 1 Press the CHECK key. Blinks. CHECK Press until the track No. to be changed is displayed. 2 Select the disc. DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 CD-404/403/DPF-R4030/R3030 Light up DISC NO. SINGLE TOTAL P.C. ALL 0 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 ÷ Perform only step 1 to simply check the program.
Programmed play (PGM mode) To clear tracks from the program 15 Press to clear tracks from the end. CLEAR ÷ Each time the key is pressed, the last track in the program is cleared. ÷ The tracks which are programmed earlier than the track being played cannot be cleared. To clear all tracks P.MODE ÷ Selected tracks can be also completely cleared just by operating the OPEN/CLOSE (0) key. ÷ The entire program is cleared.
Playback in a random order (Random playback) 16 As tracks are selected at random, you can enjoy listening to for a long time. Preparation ÷ Load a disc in the CD player. ™ 1 Check that the unit is in the TRACK mode.! 2 Press the RANDOM key. CD-406/DPF-R6030 RANDOM The number here changes. In case track No. 5 is selected CD-404/403/DPF-R4030/R3030 Blinks FILE RANDOM AUTO PAUSE PGM 1 2 2 3 DISC NO. B 4 FILE RANDOM AUTO PAUSE PGM 1 3 MULTI EDIT A SINGLE TOTAL P.C.
Repeated playback Preparation ÷ Load a disc in the CD player. 17 ™ To repeat the entire disc This allows repeated playback of all the tracks on the disc loaded in the disc tray. 1 Press so that the “PGM” indicator CD-406/DPF-R6030 goes off. P.MODE CD-404/403/DPF-R4030/R3030 PGM indicator goes off. FILE RANDOM AUTO PAUSE PGM 2 Press the REPEAT key. 1 2 3 MULTI EDIT A B 4 5 REPEAT CD-406/DPF-R6030 For the CD-406/DPF-R6030 The current status is displayed when the key is pressed once.
Repeated playback 18 To repeat only the programmed tracks 1 Press so that the “PGM” indicator CD-406/DPF-R6030 lights. P.MODE CD-404/403/DPF-R4030/R3030 2 Select the disc. DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 PGM indicator lights up. FILE RANDOM AUTO PAUSE PGM 1 2 3 MULTI EDIT A B 4 5 Go to step 3 within 8 seconds. 3 Select the desired track number. Main unit Remote control unit 1 2 3 4 5 6 7 8 9 0 +10 ÷ All of the programmed tracks will be repeated.
Editing (Except for CD-403/DPF-R3030) The following procedure allows to record a CD within the specified tape length so that no music is interrupted in the middle at the ends of sides A and B. Preparation ÷ Load a disc in the CD player. ÷ Check that the unit is in the TRACK mode. ! 1 Light the “EDIT” indicator. Do this operation in the stop mode. 1 2 3 2 4 5 6 3 7 8 9 4 5 P.MODE 0 +10 EDIT CLEAR CHECK SKIP TIME DISP. REPEAT RANDOM CD-406/DPF-R6030 Blinks.
Editing 20 To check the edited contents CD-406/DPF-R6030 CHECK ÷ When the CHECK key is pressed, track numbers and remaining time in the file A are displayed first, then those in the file B. CD-404/DPF-R4030 P.C. indicator light up. DISC NO. REPEAT TRACK NO. SINGLE TOTAL P.C. ALL 0 4 5 6 7 8 9 10 11 1 12 13 14 15 16 17 18 19 20 2 3 ÷ When the CHECK key is pressed, the track Nos. of edited songs will automatically be displayed in the order they are edited.
Timer operations Timer playback of CD can be started at any time using an audio timer which is available in audio stores. Preparation ÷ Connect the power cords of the associated components so that their power can be turned ON through the audio timer. (Also, be sure to read carefully the instruction manual of the timer.) This unit 21 System control cord Audio cord Amplifier or receiver 12 : 00 Audio timer the powers of the associated components 1 Turn ON. 2 Preparation Load a disc in the CD player.
Maintenance 22 Disc handling precautions Handling Hold the discs so that you do not touch the playing surface . Discs which can be played with this unit CD (12 cm, 8 cm) and the audio part of CDV, CD-G, CD-EG and CDEXTRA. Use discs that comply with the IEC standard, for example a disc carrying the marking on the label surface. COMPACT DIGITAL AUDIO Never play a cracked or warped disc. Label side Playing side Sticker Do not attach paper or tape to either the playing side or the label side of the discs.
In case of difficulty What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Operation to reset The microcomputer may malfunction (impossibility to operate, erroneous display, etc.) when the connection cords are unplugged while the unit is ON or due to an external factor.
Specifications 24 DPF-R6030 / CD-406 DPF-R4030/3030 / CD-404/403 [ Format ] System .......................... Compact disc digital audio system Laser ...................................................... Semiconductor laser [ Format ] System .......................... Compact disc digital audio system Laser ...................................................... Semiconductor laser [ D/A Convertors ] D/A Conversion ........................................... 1 Bit (D.R.I.V.E.) Oversampling ............
