KDC-U7056DAB KDC-U7056BT KDC-U7056BTL CD-RECEIVER Quick Start Guide © 2012 JVC KENWOOD Corporation B59-2188-10_01_13Stepup_QSG_M_En.
Contents Before use About the Quick Start Guide.......................... 2 Before use.............................................................. 2 Appendix ............................................................... 4 Preparations.......................................................... 4 General operations............................................. 6 Playing music (CD/USB/iPod)......................... 7 Listening to the radio/Digital radio.............. 8 Hands-free phoning...................
• To display characters in the following language, additional setting is required. KDC-U7056DAB KDC-U7056BT - Chinese Refer to “Chinese” of <12-5. Initial settings>. How to reset your unit If the unit fails to operate properly, press the Reset button. The unit returns to the factory settings. Reset button KDC-U7056BTL - Arabic - Persian - Thai Refer to “TAG Language” of <12-5. Initial settings>. About the discs used with this unit • This unit can only play the CDs with .
Appendix Preparations About Audio file • Playable Audio files AAC-LC (.m4a), MP3 (.mp3), WMA (.wma), WAV (.wav) of USB device • Playable disc media CD-R/RW/ROM • Playable disc file formats ISO 9660 Level 1/2, Joliet, Long file name. • Playable USB devices USB mass storage class • Playable USB device file systems FAT12, FAT16, FAT32 The online manual about audio files is put on the site, www.kenwood.com/cs/ce/audiofile/.
[Control] knob (Volume knob) [1/6] Release Adjusting the clock 1 Detaching/ Attaching the faceplate Press [Control] knob to enter the Function setting mode. The item can be selected and determined as follows. ”Settings” Á “Clock & Date” Á “Clock Adjust” Turn [Control] knob to select the item, and press [Control] knob. 2 Turn [Control] knob to adjust the hour, and then press [Control] knob. 3 Turn [Control] knob to adjust the minute, and then press [Control] knob.
General operations USB terminal [SRC] [Control] knob (Volume knob) Auxiliary input Power To turn the power ON, press [SRC]. To turn the power OFF, press and hold [SRC]. Source selection Pressing [SRC] repeatedly switches among sources.
Playing music (CD/USB/iPod) Disc slot CA-U1EX[1] [G] Disc slot cover [Control] knob KCA-iP102[1] [1/6] [E/F] [R/S] REAR USB indicator Playing a disc Open the Disc slot cover upward. Insert a disc in the Disc slot. When it is inserted, the source is switched automatically and playback starts. Close the Disc slot cover. Playing a USB device/ iPod Connect a USB device or iPod to the USB terminal as shown above. When it is connected, the source is switched automatically and playback starts.
Listening to the radio/Digital radio [SRC] [Control] knob [1/6] [R] [E/F] Selecting a tuner source 4 Selecting a band (FM or AM) (Tuner only) Recalling the stations in the memory Press [SRC] to select “TUNER” or “DIGITAL RADIO” (KDC-U7056DAB only). Refer to
Hands-free phoning [Control] knob [Ú] Pairing a Bluetooth device You can pairing your Bluetooth device in this unit. 1 Operate the Bluetooth device to request this unit for connection. The name of this unit (“KDC-####”) appears on the Bluetooth device. “Press the volume knob” appears. 2 Press [Control] knob. Connection to your Bluetooth device starts, “Pairing Success” appears a while later, and then the previous source is selected.
Before installation # WARNING • The unit can only be installed in a car with a 12V DC power supply, negative ground. • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. ! CAUTION • Use the power harness enclosed with this unit for connecting power. Using a power harness enclosed with other models can cause malfunction.
KDC-U7056DAB • This unit has the cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. 3 .....4 4 Cooling fan .....4 5 For Good Reception To assure good reception, note the following: • Communicate with the cell phone within the line-of-sight distance of 10 m (30 ft).
Rear output Front output R Subwoofer output L SW FRONT REAR Connecting wires to terminals Fuse (10A) FM/AM antenna input R Digital radio antenna (Accessory7) (KDC-U7056DAB only) Wiring harness (Accessory1) Microphone (Accessory5) (KDC-U7056BT/ KDC-U7056BTL only) To front left speaker To front right speaker To rear left speaker To rear right speaker L White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black < Ignition key switch • Speaker Impedance: 4 – 8 Ω Car fuse box ACC Re
USB connector (0.8m) To USB device. USB maximum power supply current : DC 5 V = 1 A Microphone (Accessory5) (KDC-U7056DAB only) If no connections are made, do not let the wire come out from the tab. Blue/White (Power control wire) P.CONT Blue (Antenna control wire) ANT. CONT Brown (Mute control wire) MUTE Orange/ White (Dimmer control wire) ILLUMI Light Blue/ Yellow (Steering remote control wire) REMOTE CONT STEERING WHEEL REMOTE INPUT B59-2188-10_01_13Stepup_QSG_M_En.
3 way speaker system setup Tweeter output Mid Range output R L Woofer output SW FRONT REAR Connect the speaker wires R L Wiring harness (Accessory1) To MID Range left speaker To MID Range right speaker To left Tweeter To right Tweeter White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black When using the optional power amplifier, connect this wire to its power control terminal. If no connections are made, do not let the wire come out from the tab.
2-Way/3-Way Crossover Setting Select a crossover mode 2-way or 3-way according to how the speakers are connected. 1 2 Press the [SRC] to select “STANDBY”. 3 The currently selected crossover mode is displayed. To change it, turn [Control] knob to select “YES”, and then press [Control] knob. 4 A confirmation screen appears. If you are sure you want to change the crossover mode, turn the [Control] knob to select “YES”, and then press the [Control] knob.
Installing/Removing the unit Non-Japanese cars Removing the trim plate 1 Engage the catch pins on the extraction key (Accessory2) and release the two locks on the upper part of frame. Lift up and pull the frame forward as shown in the figure. Bend the tabs of the mounting sleeve with a screwdriver or the like and attach it in place. < • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).
KDC-U7056DAB only Installing the Microphone unit Installing the Digital radio antenna 1 ! CAUTION • This film antenna is exclusively for use inside the vehicle.
KDC-U7056DAB only Installing the Digital radio antenna Installation overview Accessory67 Determining the antenna installation location • When installing the antenna on the left side Front pillar 150 mm Earth sheet Antenna cable (3.5 m) 70 mm* • The antenna should be installed on the passenger side for safety. • Use cord clamper (Accessory 8) to secure the antenna to the pillar at several locations.
Antenna Installation 1 2 3 Check the installation location. Clean the area where antenna film (Accessory 6), amplifier unit (Accessory 7), and earth sheet are pasted with the included cleaner (Accessory 9). The coating on the metal surface need not be removed. • Wait until the glass surface is completely dry before pasting. • If the glass surface is cold, such as during winter, warm it with defroster or dryer.
KDC-U7056DAB only Installing the Digital radio antenna • When installing the antenna on the left side Accessory7 Accessory6 Earth sheet Match the protrusion with 5 8 Remove the film covering the earth sheet and paste the earth sheet on the metal part of the vehicle. Provide sufficient leeway for the earth sheet so that it does not interfere with the interior parts (front pillar cover). Also take care that the interior parts do not interfere with the amplifier.
Specifications FM tuner section Frequency range 200 kHz step : 87.9 MHz – 107.9 MHz 50 kHz step : 87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 26dB) : 7.2dBf (0.63 μV/75 Ω) Quieting Sensitivity (S/N = 46dB) : 15.2dBf (1.
Requirements Pandora: Requirements for listening to the Pandora are as follows: Requirements Aha™: Requirements for listening to the Aha™ are as follows: iPhone or iPod touch iPhone or iPod touch • Use an Apple iPhone or iPod touch running under iOS3 or later. • Search for “Pandora” in the Apple iTunes App Store to find and install the most current version of the Pandora application on your device. • iPhone/ iPod touch connected to this unit with a KCA-iP102.
The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. TRA REGISTERED No. : ER0106384/13 DEALER No. : 0016026/08 B59-2188-10_01_13Stepup_QSG_M_En.
B59-2188-10_01_13Stepup_QSG_M_En.