Installation Guide

ManualsBrandsKenmore ManualsAir Conditioners77062 6,000 BTU 115V Window-Mounted Air Conditioner

READ BEFORE INSTALLING UNIT

For Low Profile Window Air Conditioner

Installation Instructions

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

edges that may be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to

move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over

an extended period of time.

Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp

metal fins of front and rear coils.

Make sure air conditioner does not fall during installation.

DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED IN THESE INSTRUCTIONS.

NOTE:

SAVE CARTON and these INSTALLATION INSTRUCTIONS for future reference. The carton is the best way to

store unit during winter, or when not in use.

Hardware ( in plastic bag)

Qty.

SUPPORT BRACKET

Qty.

LONG LEVELING BOLT

Hardware ( in plastic bag)

1/2″ SCREW

INSULATION PANEL RULER

Tools Required

RULER

HAMMER

KNIFE

PENCIL LEVEL

SCREWDRIVER (Standard and Phillips and Flathead)

SHORT LEVELING BOLT

SASH LOCK

WINDOW SASH SEAL

FOAM STRIP

WEATHER STRIPPING

(10″X3/4″X1/12″)

16120300A06462

Summary of content (5 pages)

PAGE 1
Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
PAGE 2
Installation How to Install How to install the unit 1. To prevent vibration and noise, make sure the unit is installed securely and firmly. 2. Install the unit a little slanted so the back is slightly lower than the front (about 1/4"). This will force condensed water to flow to the outside. CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. About 1/4" Install 1 Left + Right Filler Panel Assembly Place unit on floor, a bench or a table.
PAGE 3
Installation How to Install 2 Cut the FOAM STRIP to fit the underside of the window sash. Open the window, peel off the back and attach the FOAM STRIP as shown in FIG.5 3 Mark center line with pencil on the center of the inner sill, as shown in FIG.6 FIG. 6 FIG. 5 FOAM STRIP INDOOR CENTER LINE INNER SILL 4 Install support bracket on window sill. See FIG.7. Install leveling bolt up through bottom side of support bracket. You can choose a short bolt or a long one according to window type.
PAGE 4
Installation How to Install 6 SECURE THE CURTAIN FRAMES: Expand the filler panels and secure them using 4 screws as shown in FIG.10. When filler panels opens or closes, you may feel a slight resistance. This is normal. 7 WINDOW SASH SEAL AND WINDOW LOCK: Cut the window sash seal to the window width. Stuff the window sash seal between the glass and the window to prevent air and insects from getting into the room, as shown in FIG.10. FIG.
PAGE 5
Installation Instructions 9 IF AIR CONDITIONER IS BLOCKED BY STORM WINDOW FRAME: If storm window presents interference, fasten a 2″ (51mm) wide wood strip to the inner window sill across the full width of the sill. The wood strip should be thick enough to raise the height of the window sill so that unit can be installed without interference from the storm window frame, See FIG.14.