FOOD WASTE DISPOSERS GUIDE FOR EASY, TROUBLE-FREE INSTALLATION, CARE AND USE. HOW THIS GUIDE WILL HELP YOU. This guide describes everything you need to know to install your new food waste disposer, including care and use information. If you take your time, follow the instructions and drawings, you should II lll_ have no trouble making a first-rate installation.
INSTALLATION DIMENSIONS ] DISPOSER NO. A 175.6010 113/6" 6" 6%" 5" 4" 175.6012 11%" 6" 63/8" 5" 4" 175.6011 12%" 6" 63/8" 5" 4" J 175.6013 125/6" 6" 63/e' 5" 4" T 175.6035 123/," 63/," 71/," 5" 4" 1 175.6040 123/," 67/8" 73/," 53/," 4" 175.6058 13'/6" 67/8" 73/," 53/," 4" 175.60514 12'3/,6' 63/," 8'/2" 53/," 4" 175.6109 13'/," 6"h" 8%" 53/," 4" [ B* C D E* B" A E" 175.
2 REMOVING YOUR OLD DISPOSER, FIRST, TURN OFF ELECTRICAL POWER at the service panel (fuse box or circuit breaker box). If the mounting is the same as your new disposer's mounting, you can use the existing mounting. Follow instructions A through E, Step 2, then go on to Step 10. Screw Use a pipe wrench to disconnect the drain line where it attaches to the disposer discharge tube. Wire tF YOUR OLD DISPOSER HAS A DIFFERENT MOUNTING THAN YOUR NEW ONE, GO ON TO INSTRUCTION C.
HERE IS WHAT TO DO IF YOU ARE INSTALLING YOUR SINK'S FIRST DISPOSER. ENSION TUBE A. Use a pipe wrench to loosen the nut at the top of the drain trap. E. Di Now, remove the large nut at the base of the sink strainer by placing the tip of your screwdriver on the edge of the nut. (There are usually ridges to hold your screwddver.) Then strike the head of the screwdriver with a hammer in a counterclockwise direction. Next, remove the nut at the top of the sink strainer and remove the extension tube.
ET'S KEEP GOING...IT'S 7 GETTING NOW WE'RE GETrlNG INTO THE ACTUAL INSTALLATION. SEPARATE THE PARTS IN THE MOUNTING ASSEMBLY. 8 EASIER, WE HOPE. APPLY PUTTY TO THE SINK SLEEVE. Lower Screw Wrenchette First, remove the mounting assembly from the lower mounting ring, Holding the mounting assembly with one hand, insert your wrenchette or screwdriver into one of the lugs of the lower mounting ring and turn it to the left (counterclockwise) with your other hand.
I I II 11 11 WE'RE READY TO MAKE THE ELECTRICAL CONNECTIONS. NOTE: If using armored cable, we recommend installing an anti-short or insulation bushing in the end of the cable. Wire nut I Screws Do not fold or remove the brown electrical insulation paper from inside the wiring compartment. Installthe cable connector.Then loosen the connector screw(s). (Some disposers have a connector built in, on others you will have to instal/ one which must meet local electricalcodes).
2 NEXT, MAKE SURE THE DISPOSER IS GROUNDED. If the cable leading to the Green Ground Screw disposer has three wires, attach the green ground wire to the green ground screw.to the If the cable leading _o.. IA_. Attach the other end of this ground wire to the metal cold water pipe. NOTE: Be sure that this cold water pipe is continuous meta! pipe from under the sink to the ground (earth). Use only an Underwriters Laboratories, Inc. listed (approved) ground clamp to attach the ground wire to the pipe.
-r 15 NOW, ATTACH THE DISPOSER DISCHARGE TUBE TO YOUR SINK'S DRAIN TRAP. Em First, check inside the disposer grinding chamber to remove any objects or dirt that might have dropped in, Turn the disposer around to attach the discharge tube. Some models use a rubber washer that must be assembled to the discharge tube before putting the metal flange over the discharge tube, see 'D'. Secure metal flange using the edge tab on the flange and screw.
7 DISPOSER IN PLACE. NOW, LOCK THE 8 LEAKS CHECK FOR Place the end of your "wrenchette" or a screwdriver into the left side of one of the mounting ring lugs at the top of the disposer. Then, turn the "wrenchette" or screwdriver to the right until the disposer locks in place. Run water through the disposer. Then, place the stopper in the sink sleeve in the seal position. Fill the sink with water. 19 Finally, remove the stopper and let the water drain.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric appliances, basic precautions should always be followed, including the following: 1.Read all the instructions before using the appliance. t_.To reduce the risk of injury, close supervision is necessary when an appliance is used near children. 3. Do not put fingers or hands into a garbage disposer. 4.