Installation guide

ManualsBrandsKenmore Elite ManualsRoom air conditionerOfficial Kenmore Elite room air conditioner

READ BEFORE INSTALLING UNIT

MSII Window Mounting (5~8K BTU)

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

edges that may be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to

move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over

an extended period of time.

Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp

metal fins on front and rear coils.

Make sure air conditioner does not fall during installation.

• SAVE CARTON and these INSTALLATION

INSTRUCTIONS for future reference. The carton is

the best way to store unit during winter, or when not

in use.

• DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE.

• FOR SAFETY REASONS, THE TOP RAIL MUST BE

SECURELY FASTENED WITH ALL FOUR (4)

SCREWS.

Some assembly is required. Please read these instructions

carefully.

Top Rail Hardware

3/8" Screw

Qty.

Top Rail 1

Qty.

Mounting Hardware

1/2"

screws

lock frame

(For Wooden windows)

lock frame

(For Vinyl-Clad windows)

sashlock

weather seals

(6"x3/4"x1/12")

window sash seal foam

TOOLS NEEDED

o Philips Screwdriver

• Drill (If pilot holes are needed)

Before installing, the top rail must be assembled on the unit.

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A

C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B

D. Secure the top rail to the unit with the 3/8" Screws as shown in Fig. C

Packac

'Top Rail 2020211A2577

Summary of content (8 pages)

PAGE 1
READ BEFORE INSTALLING UNIT MSII Window Mounting (5~8K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. Carefully inspect location where air conditioner will be installed.
PAGE 2
LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16"). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
PAGE 3
Keepa firmgripontheairconditioner, carefullyplacetheunitintothewindowopeningsothebottomoftheair conditioner frameis againstthewindowsill(FIG.6A& FIG.6B).Carefullyclosethewindowbehindthetoprail ofthe unit. I FIG. 6A I I I FIG. 6B __1 I INslDL]E OUTSIDE INSIDE I OUTSIDE Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7A for wooden windows), windows). FIG. 7A (FIG. 7B for Vinyl-Clad FIG.
PAGE 4
To secure lower sash in place, attach right angle sash lock with 1/2" (12.7 mm) screw as shown (FIG. 10). NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself. Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11). FIG. 10 FIG. 11 Check that air conditioner is tilted back about 1/4" to 1/2" (tilted about 2 ° to 4 ° downward to the outside, see FIG. 12A & FIG. 12B).
PAGE 5
LEA ESTO ANTES DE MONTAR LA UNIDAD Montado Ventana MSII (5~8K BTU) Para evitar el riesgo de lesiones, de daSos materiales y de daSos al equipo debido a su peso y a los bordes afilados que puedan quedar expuestos: Los aparatos de aire acondicionado detallados en este manual suponen un peligro pot su excesivo peso. Es necesaria la intervenci6n de dos o mas personas para mover e instalar el equipo.
PAGE 6
MONTAJE DEL PANEL DE RELLENO IZQUIERDO Y DERECHO NOTA: El rail superior y los paneles laterales a cada lado se compensan para proporcionar el espacio necesario a la parte trasera de (5/16"). Esto es necesario para el adecuado tratamiento y drenaje del agua condensada. iSi no usa los paneles laterales por alguna razon, debe rnantener este espacio hasta la parte trasera! Ponga la unidad sobre el suelo, un banco o una mesa de trabajo.
PAGE 7
Sujetefirmemente el aparatode aireacondicionado, y col6quelo concuidadosobrelaaperturade la ventanadetalmodoquelaparteinferiordecuadroquedesobreel antepecho (FIG.6A& FIG.6B). Bajeconcuidadolaventanapordetrasdelrailsuperiorde launidad.I I FIG. 6A I I FIG. 6B __I I INTERIORL] EXTERIOR INTERIOR EXTERIOR I Ventanas de madera Ventanas de PVC Extienda los paneles laterales hasta el marco de la ventana (FIG. 7A para ventanas de madera), (FIG. 7B para ventanas de PVC). FIG. 7A FIG.
PAGE 8
Para asegurar la hoja inferior en su lugar, ajuste la placa de bloqueo para la hoja de angulo recto con tornillos de 1/2" (12.7 mm) como se muestra (FIG. 10). NOTA: Es complicado bloquear las ventanas de PVC con la placa de bloqueo, por Io que puede usar el bloqueo propio de la ventana. Corte el burlete de espuma a la medida e ins6rtelo en el espacio entre las dos hojas de la ventana (FIG. 11 ). FIG. 10 FIG.