Datasheet

19© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1092_GOLDMAX_X8R • 8/20/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Radial Through-Hole Multilayer Ceramic Capacitors
Goldmax, 300 Series, Conformally Coated, Ultra-Stable X8R Dielectric, 50 – 200 VDC (Commercial and Automotive Grade)
Ceramic Radial Tape and Reel Dimensions cont'd
Metric will govern
Variable Dimensions — Millimeters (Inches)
F
±0.78 (0.030)
1
P
1
±0.30 (0.012)
1
P
±0.3 (0.012)
P
2
±1.3 (0.51)
H
H
0
StraightLeadConguration FormedLeadConguration
2
Packaging C-Spec
3
7301/7305
7303/7317
7301/7305
7303/7317
2.54 (0.100) 5.08 (0.200) 12.7 (0.500) 6.35 (0.250)
16.0±0.5
(0.630±0.020)
18.0 (0.709)
Minimum
16.0±0.5
(0.630±0.020)
18.0 (0.709)
Minimum
4.32 (0.170) 3.89 (0.153) 12.7 (0.500) 6.35 (0.250)
5.08 (0.200) 3.81 (0.150) 12.7 (0.500) 6.35 (0.250)
5.59 (0.220) 3.25 (0.128) 12.7 (0.500) 6.35 (0.250)
6.98 (0.275) 2.54 (0.100) 12.7 (0.500) 6.35 (0.250)
7.62 (0.300) 2.24 (0.088) 12.7 (0.500) 6.35 (0.250)
9.52 (0.375) 7.62 (0.300) 12.7 (0.500) 6.35 (0.250)
10.16 (0.400) 7.34 (0.290) 25.4 (1.000) N/A
12.06 (0.475) 6.35 (0.250) 25.4 (1.000) N/A
14.60 (0.575) 5.08 (0.200) 25.4 (1.000) N/A
17.14 (0.675) 3.81 (0.15) 25.4 (1.000) N/A
1
Measured at the egress from the carrier tape, on the component side.
2
Formed lead con guration includes: "shoulder bend", "inside kink", "outside kink", and "snap-in". For more information regarding available lead
con gurations see "Dimensions" section of this document.
3
The "Packaging C-Spec" is a 4 digit code which identi es the packaging type, lead length and/or lead material. When ordering, the proper code must be
included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.
Symbol Reference Table
D
0
Sprocket Hole Diameter
P
0
Sprocket Hole Pitch
P
Component Pitch
F
Lead Spacing
P
1
Sprocket Hole Center to Lead Center
P
2
Sprocket Hole Center To Component Center
H
Height to Seating Plane (Straight Leads Only)
H
0
Height to Seating Plane (Formed Leads Only)
H
1
Component Height Above Tape Center
∆H
Component Alignment
L
1
Lead Protrusion
t
Composite Tape Thickness
W
Carrier Tape Width
W
0
Hold-Down Tape Width
W
2
Hold-Down Tape Location