User Guide
Table Of Contents
- ENGLISH
- Safety Precaution
- Accessories
- Maintenance Kit - Sold Separately (Part Number: MG100_MTKIT)
- Procedures for Using the Supplied Maintenance Kit
- Parts and Functions
- Preparation
- Attaching the Marine Case to the Camera
- Recording the Video/Still Image Files
- Detaching the camera
- Maintenance on the marine case
- Storing the O-ring
- Specifications
- DEUTSCH
- Sicherheitsvorkehrungen
- Zubehör
- Wartungsset - separat erhältlich (Teilenummer: MG100_MTKIT)
- Verwendung des mitgelieferten Wartungssets
- Teile und Funktionen
- Vorbereitung
- Einsetzen der Kamera in das Unterwassergehäuse
- Aufnehmen der Video/ Standbilddateien
- Abnehmen der Kamera
- Wartung am Unterwassergehäuse
- Lagerung des O-Rings
- Technische Daten
- FRANÇAIS
- Précautions de sécurité
- Accessoires
- Trousse d’entretien - Vendu séparément (Numéro de référence: MG100_MTKIT)
- Directives d’utilisation de la trousse d’entretien fournie
- Pièces et fonctions
- Préparation
- Fixation du boîtier sous-marin au caméscope
- Enregistrement de fichiers vidéo/ image fixe
- Détacher le caméscope
- Entretien du boîtier sous-marin
- Stockage du joint d’étanchéité
- Caractéristiques
- NEDERLANDS
- Veiligheidsvoorschriften
- Accessoires
- Onderhoudskit - afzonderlijk leverbaar (typenummer: MG100_MTKIT)
- Het gebruik van de meegeleverde onderhoudskit
- Onderdelen en toepassingen
- Voorbereiding
- Het bevestigen van het onderwaterhuis aan de camera
- Het opnemen van video/foto- bestanden
- De camera losmaken
- Onderhoud van het onderwaterhuis
- Opbergen van de O-ring
- Technische gegevens
- CASTE. ESP.
- Precauciones de seguridad
- Accesorios
- Kit de mantenimiento - Vendido por separado (Número de pieza: MG100_MTKIT)
- Procedimientos para utilizar el kit de mantenimiento suministrado
- Piezas y funciones
- Preparativos
- Colocación de la cámara en la carcasa submarina
- Grabación de archivos de vídeo/ imagen fija
- Desmontar la cámara
- Mantenimiento en la carcasa submarina
- Almacenamiento de la junta tórica
- Especificaciones
- ITALIANO
- Precauzione per la sicurezza
- Accessori
- Kit di manutenzione - In vendita separatamente (Numero parte: MG100_MTKIT)
- Procedure per l’utilizzo del Kit di manutenzione in dotazione
- Parti e funzioni
- Preparazione
- Montaggio della custodia subacquea sulla Media camera
- Registrazioni di file di video/ immagini statiche
- Staccare la Media camera
- Manutenzione sulla custodia subacquea
- Conservazione dell’anello circolare
- Caratteristiche tecniche
- РУССКИЙ
- Меры предосторожности
- Принадлежности
- Комплект для ухода – продается отдельно (код детали: MG100_MTKIT)
- Руководство по применению комплекта для ухода
- Части изделия и выполняемые ими функции
- Подготовка
- Монтаж камеры в боксе для подводной съемки
- Запись видео/файлов неподвижных изображений
- Отсоединение камеры
- Уход за боксом для подводной съемки
- Хранение уплотнительного кольца
- Технические характеристики
- POLSKI
- Środki bezpieczeństwa
- Akcesoria
- Zestaw do konserwacji – Dostępny oddzielnie (Numer katalogowy: MG100_MTKIT)
- Procedury używania zestawu do konserwacji
- Części i funkcje
- Przygotowanie
- Nakładanie obudowy podwodnej na kamerę
- Nagrywanie filmów/fotografowanie
- Zdejmowanie kamery
- Konserwacja obudowy podwodnej
- Przechowywanie pierścieni uszczelniających
- Dane techniczne
- 中文繁體
- عربي
10
Always perform maintenance on the marine case
after you have finished recording.
Salt crystal or dirt will accumulate inside the
marine case if maintenance is not performed, and
this can cause water leakage.
z Do this within 30 minutes after diving.
z Pour in fresh water until the marine case is
completely submerged in the container, and
shake the marine case in the upward,
downward, left and right directions.
z Move the buttons and levers while the marine
case is submerged, and rinse the dirt out from
any gaps or grooves. Proceed to C
z If used in the sea
-> Proceed to
Aerforming salt removal
If the marine case was used in the sea, submerge
the marine case in fresh water for at least 1 hour
to remove salt.
A
Prepare a container that contains fresh
water that is five times more than the
volume of the marine case.
z The container must be big enough to allow
the marine case to submerge fully.
z If only small containers are available, pour
in fresh water that is equivalent to at least
five times the volume of the marine case
over a few times.
z Shaking the marine case in the upward,
downward, left and right directions will be
more effective.
z Move the buttons and levers while the
marine case is submerged, and rinse the
salt out from any gaps or grooves etc.
z Make sure the grip is also free of salt.
B
Put in fresh water for at least 1 hour.
C
Remove the marine case and wipe off
water droplets on the case surface using a
dry towel.
D
Remove the camera.
z Face the front glass of the marine case
upwards, and open the buckles to remove
the camera, while paying attention not to let
water droplets at O-ring or buckles enter
the case.
z The camera may fall out if the buckles are
opened with the front glass facing down.
z If you cannot avoid opening the marine case at
the diving location, pay attention not to let
water droplets from your hair or your body
enter the case.
E
Remove the O-ring, and wipe off salt, sand
and other foreign matter.
z Also wipe the groove in which the O-ring
was inserted, and the part of the marine
case that was in contact with the O-ring,
and allow them to dry.
¹ For details on handling and storing the
O-ring, refer to the “O-ring Maintenance
Manual”.
F
Wipe the inside and outside of the marine
case with a dry cloth.
¹ Use a lint-free cloth to wipe the inside of
the marine case.
G
Wipe the inner side of the front glass.
z Add a few drops of the cleaner liquid onto
the inner side of the front glass, and wipe
off using lens tissue paper etc.
z The front glass will fog if it is dirty.
Maintenance on the marine case
Wash the marine case in water
while it is still sealed
Performing salt removal
Caution
Caution
Dirt, sand, salt
crystals, etc.
Hair, lint, etc.
WR-MG100_EN.book Page 10 Wednesday, December 5, 2007 1:23 PM