Specification

One Lithonia Way, Conyers, GA 30012 | (800) 705-SERV (7378)| www.acuitybrands.com
© 2021 Acuity Brands Lighting, Inc. All rights reserved. Rev. 12/13/21 Page 2 of 2
CONTRACTOR SELECT WF4_WF6_WF8 SWW5
HOUSING:
Polycarbonate injection molded outer frame, with steel back plate. Non-conductive
dead-front trim design suitable for a wide range of applications and codes requiring a
non-conductive lens • FT4 3-pin plenum rated cable connector to connect from module to
remote driver box • Steel spring clip for easy installation. 4", 6" or 8" cut out template is
provided to ensure a correct sized hole is cut into ceiling for proper installation of the trim.
Size of hole should not exceed 4-1/4" for the WF4, 6-1/4" for the WF6 and 8-1/4" for the
WF8 • Can be installed from 3/8" to 1 ½" ceiling thickness • Can be removed from below
the ceiling for service or replacement.
LED LIGHT ENGINE:
Switchable white color temperature from 2700K, 3000K, 3500K, 4000K, 5000K • 90 CRI
minimum • Color accuracy within 4 step McAdams Ellipse at the end CCT (2700K and
5000K), within 6 step McAdams Ellipse in the middle CCT (3000K, 3500K, and 4000K)
• Dimming 100% to 10% with most standard incandescent dimmers (see list of approved
dimmers).
DRIVER:
Connect directly to 120V Class-2 (CAN ICES-005 (B) / NMB-005 (B)) LED driver. 120V 60 Hz
constant current driver provides noise free operation • IC rated driver with convenience
of a switch to choose between 5 selectable color temperature options ranging from
2700K (warm white), 3000K, 3500K, 4000K, or 5000K (daylight) • The isolated driver
integrated inside steel remote box with four 7/8" knockouts with slots for pryout. Suitable
for pulling wires with the 12 cubic-inch wiring compartment to accommodate up to (6)
14 gauge insulated conductor, or (4) 12 gauge insulated conductors; making the Wafer
LED Downlights much easier to wire in 2in/2out (plus ground) daisy-chain applications
and contractor friendly • 2" plenum space required for installation of the remote driver
box • Suitable for installation in t-grid and drop ceiling applications with universal new
construction pan.
OPTICAL SYSTEM:
Edge-lit LED technology uses light guided plate to distribute light • Polycarbonate lens
provides even illumination throughout the space • Efcient system that can produce over
670 lumens while using 9W (WF4), 970 lumens while using 13W (WF6) and 1640 lumens
while using 19W (WF8) • Replaces 65W incandescent (WF4), 75W incandescent (WF6) and
100W incandescent (WF8).
LIFE:
Rated for 50,000 hours at 70% lumen maintenance.
LABELS:
CSA certied to US and Canadian safety standards • ENERGY STAR® certied product
• Suitable for wet location • Air-Loc certied in accordance with ASTM E283-2004 • NOM
Certied • Can be used to comply with California Title 24 Part 6 High Efcacy LED light
Source Requirements • U.S. Patent No. 10,681,784.
TESTING:
All reports are based on published industry procedures; eld performance may differ from
laboratory performance.
WARRANTY:
3-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/support/warranty/terms-and-conditions
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specications subject to change without notice.
Specifications Dimensions
4.1"
1.2"
5"
3.3"
.5"
5.5"
1.3"
5.9"
5.1"
7"
5"
1.2"
8"
7.2"
8.9"
.5"
1.2"
3.0"
WF4
WF6
WF8
PERFORMANCE DATA
WF4 SWW5 WF6 SWW5 WF8 SWW5
Input Voltage 120V 120V 120V
Input Power Typical 9W (+/-5%) 13W (+/-5%) 19W (+/-5%)
Frequency 60 Hz 60 Hz 60 Hz
EMI/RFI FCC Title 47, Part 15
Class B (consumer)
FCC Title 47, Part 15
Class B (consumer)
FCC Title 47, Part 15
Class B (consumer)
Minimum Starting Temp -40°F (-40°C) -40°F (-40°C) -40°F (-40°C)
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25°C.