Use & Care Guide

ENGINEERING DATA
UPX109 UPX214 UPX322 UPX430
Total input power (watts) 20 40 60 80
Total Operating AMPS .17 .34 .50 .70
Power Factor .99 .99 .99 .99
REV-2/07
PRODUCT SPECIFICATIONS
Lamp 20W-12-volt xenon bi-pin high output lamps supplied with
fixture • Projected 10,000 hour life based on actual operating
voltage in fixture.
Transformer Integral Electronic 120 to 12-volt step down
transformer is accessible for maintenance without having to
remove fixture.
Housing Extruded aluminum • Designer white, black, brushed
bronze or brushed silver finish.
Reflector Specular aluminum reflector behind each lamp.
Diffuser Clear prismatic tempered glass lens for maximum light
transmission • Reverse-angled to minimize preceived brightness
• Captive lens has hinged design for tool-less relamping • Spring-
loaded retention bar prevents lens from accidently being bumped
loose.
Switch Convenient integral Hi/Lo/Off rocker switch.
Dimming For best results use dimmer specifically designed for use
with electronic low voltage transformers.
Labels UL Listed.
DIMENSIONS
UNDERCABINET LIGHTING
PRO-XENON
20W - 12-volt Xenon Lamps
UPX109, UPX214,
UPX322 and UPX430
I1.5.0
Project:
Fixture Type:
Location:
Contact/Phone:
PRODUCT DESCRIPTION
The Pro-Xenon modular series with integral electronic transformer
operates 12-volt halogen lamps to deliver the best color rendering
with maximum light output and lamp life. The efficient operation of
low voltage lamps, along with a unique housing/reflector system,
reduces mounting surface temperatures well below what is typical
for xenon undercabinet fixtures. Pro-Xenon fixtures are optimized
for fast permanent installation, mounting either flush to the rear
backsplash or to the front lip of cabinetry to suit project conditions
and homeowner preference.
INSTALLATION
UPX series fixtures optimized with a center rear wiring access
compartment and push-in 3-wire electrical connectors for quick
electrical connection without having to open the fixture or remove
the lens. Rear wiring access compartment covers provided with
push-in connector for non-metallic cable and knockout for feed thru
wiring capability. Multiple off-center knockouts provided in two,
three and four lamp fixtures. Die-cast fitting for 3/8” flexible metal
conduit supplied in a hardware pack. Fixtures may be mounted
flush to the backsplash or up against the front lip of the cabinetry
using captive external mounting screws.
Portable To install as a portable fixture, use the 3-wire grounded
cord & plug (ULH-CP sold separately).
Optional Direct Wire Optional direct wire module (ULH-DWM
sold separately) facilitates code-compliant installation of fixture at
front edge of cabinetry. Supplied with 36” field-shortenable
jumper cord to bring power to either end of the fixture.
Electrically Connecting Multiple Fixtures Up to 10 fixtures
may be electrically joined together using either the straight joiner
connector supplied with each fixture or the optional JC3 jumper
cords. See accessories table for lengths and finishes.
ACCESSORIES
Catalog No. Description
JC3-8-WH,-BL 8” Jumper Cord
JC3-17-WH,-BL 17” Jumper Cord
JC3-26-WH,-BL 26” Jumper Cord
ULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
ULH-DWM-WH,-BL Direct Wire Module
UPX-LAMP 12V 20W Bi-Pin Xenon High Output Lamp
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
UPX109-BL Black 9
1
/
2
” 1-20W
UPX109-BZ Brushed Bronze 9
1
/
2
” 1-20W
UPX109-SL Brushed Silver 9
1
/
2
” 1-20W
UPX109-WH Designer White 9
1
/
2
” 1-20W
UPX214-BL Black 14” 2-20W
UPX214-BZ Brushed Bronze 14” 2-20W
UPX214-SL Brushed Silver 14” 2-20W
UPX214-WH Designer White 14” 2-20W
UPX322-BL Black 22” 3-20W
UPX322-BZ Brushed Bronze 22” 3-20W
UPX322-SL Brushed Silver 22” 3-20W
UPX322-WH Designer White 22” 3-20W
UPX430-BL Black 30” 4-20W
UPX430-BZ Brushed Bronze 30” 4-20W
UPX430-SL Brushed Silver 30” 4-20W
UPX430-WH Designer White 30” 4-20W
PRO-XENON 5 MINUTE DIRECT-WIRE INSTALLATION
Step 1 Attach supply
wires to rear access cover.
Step 2 Connect supply
wires to fixture leads
using push-in connectors.
Step 3 Mount fixture to
cabinet bottom using
captive mounting screws.
Maximum cabinet bottom contact temperature: less than 60˚ C.
1"
4 1/2"