Notice d'utili‐ sation JGVN60415 Benutzerin‐ formation Istruzioni per l’uso Lave-vais‐ selle Geschirrspü‐ Lavastoviglie ler
TABLE DES MATIÈRES Consignes de sécurité Instructions de sécurité Description de l'appareil Bandeau de commande Programmes Réglages Options 2 3 5 5 6 7 10 Avant la première utilisation Utilisation quotidienne Conseils Entretien et nettoyage En cas d'anomalie de fonctionnement Caractéristiques techniques 10 12 13 15 17 20 Sous réserve de modifications. CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies.
pour une utilisation privée, par les clients, dans des hôtels et autres lieux de séjour. Ne modifiez pas les caractéristiques de cet appareil. La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (Mpa) Respectez le nombre maximum de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger.
• Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation. Le remplacement du cordon d'alimentation de l'appareil doit être effectué par notre service après-vente. • Ne connectez la fiche d'alimentation secteur à la prise de courant secteur qu'à la fin de l'installation. Assurez-vous que la fiche d'alimentation est accessible une fois l'appareil installé. • Ne tirez jamais sur le câble d'alimentation électrique pour débrancher l'appareil. Tirez toujours sur la fiche.
• Retirez le dispositif de verrouillage de la porte pour empêcher les enfants et les animaux de s'enfermer dans l'appareil.
5 Voyants Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme.
Valeurs de consommation Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 11 1.050 195 13 - 15 1.5 - 1.6 150 - 170 15 - 17 1.3 - 1.6 120 - 130 9 0.8 30 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées.
Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région. Il est important de régler l'adoucisseur d'eau sur un niveau adéquat pour vous garantir de bons résultats de lavage.
– Par exemple, 5 clignotements + pause + 5 clignotements = niveau 5. 3. Appuyez sur de façon répétée pour modifier le réglage. Le niveau augmente à chaque fois que vous appuyez sur la touche . Lorsque vous atteignez le niveau 10 et que vous appuyez à nouveau sur la touche, le réglage revient au niveau 1. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. Distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. 2.
OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme. Vous ne pouvez pas activer ni désactiver d'options pendant le déroulement d'un programme. Certaines options ne sont pas compatibles entre elles. Si vous avez choisi des options incompatibles, l'appareil en désactivera automatiquement une ou plusieurs. Seuls les voyants correspondant aux options encore actives resteront allumés.
Comment remplir le distributeur de liquide de rinçage A D B 4. Enlevez le sel qui se trouve autour de l'ouverture du réservoir de sel régénérant. C B A M AX 4 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir. De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme.
UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. • Si le voyant du réservoir de sel régénérant est allumé, remplissez le réservoir. • Si le voyant du liquide de rinçage est allumé, remplissez le distributeur de liquide de rinçage. 3. Chargez les paniers. 4. Ajoutez le produit de lavage. Si vous utilisez des pastilles de détergent tout en 1, activez l'option Multitab. 5.
Le voyant du départ différé s'allume. 3. Fermez la porte de l'appareil pour lancer le décompte. En cours de décompte, il est possible d'augmenter le nombre d'heures du départ différé, mais pas de changer la sélection du programme. Lorsque le décompte est terminé, le programme démarre. Ouverture de la porte au cours du fonctionnement de l'appareil Si vous ouvrez la porte lorsqu'un programme est en cours, l'appareil s'arrête.
Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle. D'autres produits peuvent endommager l'appareil. • Les pastilles tout en 1 sont généralement adaptées aux régions où la dureté de l'eau est inférieure à 21 °dH.
Avant le démarrage d'un programme • Vous utilisez la bonne quantité de produit de lavage. Assurez-vous que : Déchargement des paniers • Les filtres sont propres et correctement installés. • Le bouchon du réservoir de sel régénérant est vissé. • Les bras d'aspersion ne sont pas obstrués. • Vous avez utilisé du sel régénérant et du liquide de rinçage (sauf si vous utilisez des pastilles tout en 1). • La vaisselle est bien positionnée dans les paniers.
ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. Nettoyage extérieur 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat (A) en place.
EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête inopinément, avant de contacter votre Service Après Vente, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations reprises dans le tableau. Avec certains problèmes, le voyant de fin clignote indiquant une anomalie. La plupart des problèmes qui surviennent peuvent être résolus sans avoir besoin de recourir à un Service Après Vente.
Problème et code de l'alarme Cause et résolution possibles Le dispositif anti-inondation est activé. • Le voyant de fin clignote 3 fois de façon intermittente. • Le signal sonore retentit 3 fois de façon intermittente. • Fermez l'arrivée d'eau et contactez un Centre après-vente agréé. L'appareil s'arrête et redémarre plusieurs fois pendant le fonctionnement. • C'est normal. Cela permet d'atteindre des résultats optimaux en matière de propreté et d'économies d'énergie.
Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Si vous utilisez des pastilles tout en 1, activez toujours l'option Multitab. Résultats de séchage insatisfaisants. • La vaisselle est restée trop longtemps à l'intérieur de l'appareil, porte fermée.
Problème Cause et solution possibles Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble. Évitez de placer les couverts en argent et en acier inoxydable les uns à côté des autres. Il y a des résidus de détergent dans le distributeur de produit de lavage à la fin du programme.
Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour d'autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le symbole .
INHALTSVERZEICHNIS Sicherheitsinformationen Sicherheitsanweisungen Gerätebeschreibung Bedienfeld Programme Einstellungen Optionen 22 23 25 26 26 27 30 Vor der ersten Inbetriebnahme Täglicher Gebrauch Tipps und Hinweise Reinigung und Pflege Fehlersuche Technische Daten 30 32 33 35 37 41 Änderungen vorbehalten. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung.
Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (Mpa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
Elektrischer Anschluss WARNUNG! Brand- und Stromschlaggefahr. • Das Gerät muss geerdet sein. • Stellen Sie sicher, dass die elektrischen Daten auf dem Typenschild den Daten Ihrer Stromversorgung entsprechen. Wenden Sie sich andernfalls an eine Elektrofachkraft. • Schließen Sie das Gerät nur an eine ordnungsgemäß installierte Schutzkontaktsteckdose an. • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen.
Service Entsorgung • Wenden Sie sich zur Reparatur des Geräts an den autorisierten Kundendienst. Wir empfehlen nur Originalersatzteile zu verwenden. • Wenn Sie sich an den autorisierten Kundendienst wenden, sollten Sie folgende Angaben, die Sie auf dem Typenschild finden, zur Hand haben. Modell: Produkt-Nummer (PNC): Seriennummer: WARNUNG! Verletzungs- und Erstickungsgefahr. • Trennen Sie das Gerät von der Stromversorgung. • Schneiden Sie das Netzkabel ab, und entsorgen Sie es.
BEDIENFELD 1 1 Taste „Ein/Aus“ 2 Programmwahltasten 3 Taste Multitab 2 3 4 5 4 Taste Delay 5 Kontrolllampen Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe „Programmende“. Kontrolllampe Salz. Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel. Sie erlischt während des Programmbetriebs.
Programm 3) Verschmutzungsgrad Beladung Programmphasen Optionen • Vor Kurzem benutztes Geschirr • Geschirr und Besteck • Hauptspülgang 60 °C oder 65 °C • Spülgänge • Multitab 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. (Dies ist das Standardprogramm für Prüfinstitute.) 2) Dieses Programm enthält eine Spülphase mit hoher Temperatur, um hygienischere Spülergebnisse zu liefern.
Spülergebnisse und das Gerät auswirken könnten. Einstellen des Programmwahlmodus Je höher der Mineralgehalt ist, um so härter ist das Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Das Gerät befindet sich im Programmwahlmodus, wenn nur die Programmkontrolllampe leuchtet. Wenn Sie das Gerät einschalten, befindet es sich normalerweise im Programmwahlmodus.
Reinigungstabletten ohne Salz, stellen Sie die korrekte Wasserenthärterstufe ein, damit die Salznachfüllanzeige nicht ausgeschaltet wird. Ist der Klarspülmittel-Dosierer ausgeschaltet, leuchtet die entsprechende Kontrolllampe nie. Einstellen des Wasserenthärters Ausschalten des KlarspülmittelDosierers Das Gerät muss sich im Programmwahlmodus befinden: Das Gerät muss sich im Programmwahlmodus befinden. 1.
gedrückt, bis die Kontrolllampen , und blinken. 2. Drücken Sie . und • Die Kontrolllampen erlöschen. blinkt weiter. • Die Kontrolllampe • Die Kontrolllampe erlischt. 3. Drücken Sie zum Ändern der Einstellung. • Die Kontrolllampe leuchtet auf. Der Signalton für das Programmende ist eingeschaltet. 4. Drücken Sie die Taste Ein/Aus zur Bestätigung der Einstellung. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten.
Salzbehälter ACHTUNG! Verwenden Sie nur Spezialsalz für Geschirrspüler. Füllen des KlarspülmittelDosierers A D B Das Salz wird für die Regenerierung des Filterharzes im Wasserenthärter und zur Erzielung guter Spülergebnisse im täglichen Gebrauch benötigt. So füllen Sie den Salzbehälter: 1. Drehen Sie den Deckel des Salzbehälters gegen den Uhrzeigersinn und entfernen Sie ihn. 2. Füllen Sie 1 Liter Wasser in den Salzbehälter (nur beim ersten Mal). 3. Füllen Sie den Salzbehälter mit Geschirrspülsalz.
TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet. • Leuchtet die Kontrolllampe Klarspülmittel, füllen Sie den Klarspülmittel-Dosierer. 3. Beladen Sie die Körbe. 4. Füllen Sie Reinigungsmittel ein. Wenn Sie die Multi-Reinigungstabletten verwenden, schalten Sie die Option Multitab ein. 5.
Starten eines Programms mit Zeitvorwahl 1. Wählen Sie ein Programm. 2. Drücken Sie wiederholt, bis die Kontrolllampe der gewünschten Startzeitverzögerung leuchtet (3, 6 oder 9). Die Kontrolllampe der Zeitvorwahl leuchtet auf. 3. Schließen Sie die Gerätetür, um den Countdown zu starten. Während des Countdowns kann die Zeitvorwahl erhöht werden, aber das ausgewählte Programm lässt sich nicht ändern. Nach Ablauf der Zeitvorwahl wird das Programm gestartet.
• Spülen Sie das Geschirr nicht von Hand vor. Verwenden Sie bei Bedarf das Vorspülprogramm (wenn verfügbar) oder wählen Sie ein Programm mit Vorspülgang. • Nutzen Sie die Körbe immer ganz aus. • Wenn Sie das Gerät beladen, achten Sie darauf, dass das Geschirr komplett von dem Wasser aus den Sprüharmdüsen erreicht und gespült wird. Achten Sie darauf, dass das Geschirr sich weder berührt noch von anderem Geschirr verdeckt wird.
• Weichen Sie eingebrannte Essensreste ein. • Ordnen Sie hohle Gefäße (z. B. Tassen, Gläser, Pfannen) mit der Öffnung nach unten ein. • Stellen Sie sicher, dass Geschirr und Besteck nicht aneinander haften. Mischen Sie Löffel mit anderem Besteck. • Achten Sie darauf, dass Gläser einander nicht berühren. • Ordnen Sie kleine Gegenstände in den Besteckkorb ein. • Ordnen Sie leichte Gegenstände im Oberkorb an. Achten Sie darauf, dass diese nicht verrutschen können.
2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus.
Reinigung des Geräteinnenraums mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden. • Um die Leistungsfähigkeit des Geräts zu erhalten, wird empfohlen einmal im Monat ein spezielles Reinigungsmittel für Geschirrspüler zu verwenden. Befolgen Sie sorgfältig die Anweisungen auf der Reinigungsmittelverpackung. • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch.
Problem und Alarmcode Mögliche Ursachen und Abhilfe Es läuft kein Wasser in das Gerät. • Die Kontrolllampe Programmende blinkt einmal. • Der Signalton ertönt einmal. • Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Information erhalten Sie von Ihrem Wasserversorger. • Vergewissern Sie sich, dass der Wasserzulauf nicht verstopft ist.
Problem und Alarmcode Mögliche Ursachen und Abhilfe Das Gerät löst die Sicherung aus. • Die abgesicherte Stromstärke reicht nicht für den gleichzeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw. der Stromzähler zugelassen ist, und schalten Sie eines der eingeschalteten Geräte aus. • Ein Fehler in der Elektrik des Geräts. Wenden Sie sich an den autorisierten Kundendienst.
Störung Mögliche Ursachen und Abhilfe Das Geschirr ist nass. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen. Probieren Sie eine andere Marke aus oder schalten Sie den Klarspülmittel-Dosierer ein und verwenden Sie ihn zusammen mit den Multi-Reinigungstabletten.
TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe (mm) 596 / 818 - 898 / 555 Elektrischer Anschluss 1) Spannung (V) 220 - 240 Frequenz (Hz) 50 Wasserdruck Min./max. bar (MPa) 0.5 (0.05) / 8 (0.8) Wasserversorgung Kalt- oder Warmwasser 2) max. 60 °C Fassungsvermögen Maßgedecke 13 Leistungsaufnahme Ein-Zustand (W) 5.0 Leistungsaufnahme Aus-Zustand (W) 0.10 1) Weitere Angaben finden Sie auf dem Typenschild. 2) Wenn Sie Heißwasser mit umweltfreundlichen, alternativen Energiequellen (z.
INDICE Informazioni per la sicurezza Istruzioni di sicurezza Descrizione del prodotto Pannello dei comandi Programmi Impostazioni Opzioni 42 43 45 45 46 47 49 Preparazione al primo utilizzo Utilizzo quotidiano Consigli e suggerimenti utili Pulizia e cura Risoluzione dei problemi Dati tecnici 50 51 53 54 56 60 Con riserva di modifiche. INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura.
clienti di hotel, motel, bed and breakfast e altri ambienti residenziali. Non apportare modifiche alle specifiche di questa apparecchiatura. La pressione di esercizio dell'acqua (minima e massima) deve essere compresa tra 0.5 (0.05) / 8 (0.8) bar (Mpa) Rispettare il numero massimo di 13 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, da un tecnico autorizzato o da una persona qualificata per evitare situazioni di pericolo.
• Non utilizzare prese multiple e prolunghe. • Accertarsi di non danneggiare la spina e il cavo. Qualora il cavo elettrico debba essere sostituito, l’intervento dovrà essere effettuato dal nostro Centro di Assistenza autorizzato. • Inserire la spina di alimentazione nella presa solo al termine dell'installazione. Verificare che la spina di alimentazione rimanga accessibile dopo l'installazione. • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina.
• Rimuovere il blocco porta per evitare che bambini e animali domestici rimangano chiusi all'interno dell'apparecchiatura.
5 Spie Spie Spia Descrizione Spia di fine. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma.
Programma 1) Acqua (l) Energia (kWh) Durata (min.) 13 - 15 1.5 - 1.6 150 - 170 15 - 17 1.3 - 1.6 120 - 130 9 0.8 30 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.test@dishwasher-production.
Durezza dell'acqua Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
Utilizzo del brillantante e delle pastiglie multifunzione Quando si attiva l'opzione Multitab, il contenitore del brillantante continua a rilasciare il brillantante.. È possibile disattivare il contenitore del brillantante. I questo caso i risultati di asciugatura potrebbero non essere soddisfacenti. Con il contenitore del brillantante disattivato, la spia corrispondente è sempre spenta. Come disattivare il contenitore del brillantante L'apparecchiatura deve essere in modalità di selezione programma.
Multitab Attivare questa opzione quando si utilizzano pastiglie multifunzione contenenti sale, brillantante e detersivo. Possono contenere anche altri agenti pulenti o di risciacquo. aumentare i risultati di pulizia ed asciugatura con l'uso di pastiglie multifunzione. Multitab non è un'opzione permanente e deve essere selezionata ad ogni ciclo. Questa opzione disattiva il rilascio di sale. La spia del sale non si accende.
Come riempire il contenitore del brillantante A D B C B A 4 1 3 2 1. Premere il tasto di sgancio (D) per aprire il coperchio (C). 2. Versare il brillantante nel contenitore (A) finché il liquido raggiunge il livello di max. 3. Rimuovere l'eventuale brillantante fuoriuscito con un panno assorbente, per evitare che si formi troppa schiuma. 4. Chiudere il coperchio. Assicurarsi che il pulsante di sgancio si blocchi in posizione.
A 30 B La spia del programma corrispondente si accende. 4. Chiudere la porta dell'apparecchiatura per avviare il programma. D 20 Avvio del programma con partenza ritardata C 1. Premere il tasto di sgancio (B) per aprire il coperchio (C). 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (A). 3. Se il programma prevede una fase di prelavaggio, mettere una piccola quantità di detersivo nel contenitore (D). 4. Chiudere il coperchio.
Annullamento del programma Tenere premuti contemporaneamente e finché l’apparecchiatura entra in modalità di selezione programma. Verificare che vi sia del detersivo nell'apposito contenitore prima di avviare un nuovo programma. viene disattivata entro 5 minuti, tutte le spie si spengono. Ciò contribuisce a ridurre il consumo di energia. 1. Per disattivare l'apparecchiatura premere il tasto On/Off o attendere che la funzione Auto Off spenga automaticamente l'apparecchiatura. 2.
Cosa fare se non si desidera utilizzare più il detersivo in pastiglie multifunzione Prima di iniziare ad usare separatamente detersivo, sale e brillantante attenersi alla procedura seguente: 1. Impostare il livello più alto del decalcificatore dell'acqua. 2. Assicurarsi che i contenitori del sale e del brillantante siano pieni. 3. Avviare il programma più breve con una fase di risciacquo. Non aggiungere il detersivo e non caricare i cestelli. 4.
Pulizia dei filtri Il sistema del filtro si compone di 3 parti. C B A 1. Ruotare il filtro (B) in senso antiorario e rimuoverlo. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 5. Assicurarsi che non vi siano residui di cibo o di sporco all'interno o attorno al bordo della vasca di raccolta. 6. Posizionare nuovamente il filtro piatto (A). Assicurarsi che sia posizionato correttamente al di sotto delle due guide. 7. Rimontare i filtri (B) e (C). 8.
Pulizia interna AVVERTENZA! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. • Pulire accuratamente l'apparecchiatura, inclusa la guarnizione in gomma della porta, con un panno morbido umido. • Se si usano regolarmente programmi di breve durata, è possibile riscontrare depositi di grasso e calcare all'interno dell'apparecchiatura. Per evitarlo, si consiglia di avviare programmi lunghi almeno 2 volte al mese.
Problema e codice allarme Possibile causa e soluzione Il programma non si avvia. • Controllare che la porta sia chiusa. • Se è stata impostata la partenza ritardata, annullare l'impostazione o attendere il termine del conto alla rovescia. • L'apparecchiatura ha avviato la procedura di rigenerazione della resina all'interno del decalcificatore. La procedura dura all'incirca 5 minuti. L'apparecchiatura non carica acqua. • La spia di fine programma lampeggia una volta in modo intermittente.
Problema e codice allarme Possibile causa e soluzione Tintinnio/colpi dall'interno dell'apparecchiatura. • Le pentole e le stoviglie non sono state sistemate adeguatamente nei cestelli. Fare riferimento al libretto contenente le indicazioni per caricare il cestello. • Accertarsi che i mulinelli possano girare liberamente. L'apparecchiatura fa scattare l'interruttore principale. • L'amperaggio è insufficiente per sopportare l'uso di più apparecchiatura contemporaneamente.
Problema Possibile causa e soluzione Macchie e tracce di gocce d'acqua su bicchieri e stoviglie. • La quantità di brillantante erogata non è sufficiente. Regolare il livello del brillantante su una posizione superiore. • La causa potrebbe essere la qualità del brillantante. Le stoviglie sono bagnate. • Il programma non dispone di una fase di asciugatura oppure questa fase viene eseguita a bassa temperatura. • Il contenitore del brillantante è vuoto.
Fare riferimento a "Preparazione al primo utilizzo", "Utilizzo quotidiano" o "Consigli e suggerimenti" per altre possibili cause. DATI TECNICI Dimensioni Larghezza/Altezza/Profondità (mm) 596 / 818 - 898 / 555 Collegamento elettrico 1) Tensione (V) 220 - 240 Frequenza (Hz) 50 Pressione dell’acqua di alimentazione Min./max. bar (MPa) 0.5 (0.05) / 8 (0.8) Collegamento dell'acqua Acqua fredda o calda 2) max. 60°C Capacità Coperti 13 Consumo di energia Modalità Acceso (W) 5.
100006681-A-262015