Use and Care Manual
Table Of Contents
- ProShop II™ 10-inch Table Saw
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 Table of contents
- 3.0 About this manual
- 4.0 Table Saw terminology
- 5.0 Specifications
- 6.0 Setup and assembly
- 6.1 Shipping contents
- 6.2 Tools required for assembly
- 6.3 Unpacking and cleanup
- 6.4 Installing legs and levelers
- 6.5 Extension wings
- 6.6 Handwheels
- 6.7 Motor cover
- 6.8 Rails and fence
- 6.9 Wood extension table
- 6.10 Switch bracket
- 6.11 Dust collection
- 6.12 Riving knife
- 6.13 Anti-kickback pawls
- 6.14 Blade guard
- 6.15 Blade installation/replacement
- 6.16 Low profile riving knife
- 6.17 Table insert
- 6.18 Miter gauge
- 6.19 Tool storage
- 7.0 Electrical connections
- 8.0 Adjustments
- 9.0 Operations
- 10.0 Safety devices
- 11.0 User-maintenance
- 12.0 Optional accessories
- 13.0 Troubleshooting JPS2 ProShop II
- 14.0 Replacement Parts
- 14.1.1 Motor and Trunnion – Exploded View
- 14.1.2 Motor and Trunnion – Parts List
- 14.2.1 Table and Cabinet– Exploded View
- 14.2.2 Table and Cabinet– Parts List
- 14.3.1 Stand Assembly – Exploded View
- 14.3.2 Stand Assembly – Parts List
- 14.4.1 Switch Assembly – Exploded View
- 14.4.2 Switch Assembly – Parts List
- 14.5.1 Blade Guard Assembly – Exploded View
- 14.5.2 Blade Guard Assembly – Parts List
- 14.6.1 Miter Gauge Assembly – Exploded View
- 14.6.2 Miter Gauge Assembly – Parts List
- 15.0 Electrical Connections for JPS2
- 16.0 Warranty and Service
11
Read and understand all
assembly instructions before attempting
assembly. Failure to comply may cause serious
injury.
6.0 Setup and assembly
6.1 Shipping contents
See Figures 6-1 and 6-2.
NOTE: Some parts may have come pre-assembled
to the table saw.
1 Table saw with on/off switch (not shown)
1 Blade (preinstalled on saw)
1 Table insert (preinstalled on saw)
1 Arbor wrench (preinstalled on tool holder)
1 Miter gauge – A
1 Push stick – B
1 Handwheel, large mounting hole – C
1 Handwheel, small mounting hole – D
1 Guard assembly – E
1 Anti-kickback pawl assembly – F
1 Riving knife – G
1 Low profile riving knife – H
1 Motor cover – J
4 Legs – K
2 Extension wings – L
1 Operator’s manual (not shown)
1 Product registration card (not shown)
1 Hardware package
6.1.2 Hardware package
1 Storage hook – HP1
1 Open end wrench 11-13mm – HP2
1 Knob – HP3
1 Spacer – HP4
3 Hex wrenches, 2.5, 4, 5 mm – HP5
4 Levelers – HP6
8 Socket hd cap screws M8x20 – HP7
8 Socket hd cap screws M6x16 – HP8
1 Soc hd cap screw w/lock wshr M5x12 – HP9
2 Tapping screws M5x12 – HP10
2 Hex cap screws w/flat wshr M8x10 – HP11
4 Pan hd machine screws M6x16 – HP12
8 Flat washers M8 – HP13
12 Flat washers M6 – HP14
4 Hex nuts M8 – HP15
NOTE: Fence and rail assemblies with fasteners,
and wood extension tables and legs with fasteners,
are shipped in separate boxes.
Figure 6-1: Contents (not to scale)
Figure 6-2: Hardware (not to scale)