Use and Care Manual
Table Of Contents
- JJP-8BT Jointer-Planer
- 1.0 Warranty and Service
- 2.0 Table of contents
- 3.0 Safety warnings
- 4.0 Features
- 5.0 Specifications
- 6.0 Setup and assembly
- 7.0 Assembly
- 8.0 Jointer setup
- 9.0 Planer setup
- 10.0 Operating controls
- 11.0 Adjustments
- 12.0 Basic Operations
- 13.0 Maintenance
- 14.0 Lubrication
- 15.0 Optional Accessories
- 16.0 Troubleshooting the JJP-8BT
- 17.0 Replacement Parts
- 17.1.1 Jointer/Planer – Parts List
- 17.1.2 Assembly Drawing Index
- 17.1.3 Planer Table Assembly
- 17.1.4 Motor Assembly
- 17.1.5 Front Frame Assembly
- 17.1.6 Chain Drive Assembly
- 17.1.7 Front Cover Assembly
- 17.1.8 Cutterhead Guard Assembly
- 17.1.9 Dust Cover Assembly
- 17.1.10 Jointer Infeed Table Assembly
- 17.1.11 Jointer Outfeed Table Assembly
- 17.1.12 Cutterhead/Feed Roller Assembly
- 17.1.13 Jointer Fence Assembly
- 17.1.14 Rear Frame and Cover Assembly
- 17.2.1 Jointer/Planer Stand – Parts List
- 17.2.2 Jointer/Planer Stand – Exploded View
- 18.0 Electrical Connections – JJP-8BT
9
7.0 Assembly
For assembly convenience, the item letter
designators used throughout the Assembly section
are the same as those used to identify shipping
content and hardware components in sect. 6.0.
7.1 Stand assembly (optional)
Note: If you do not plan to use a stand at this time,
skip this page and proceed to sect. 7.3, Jointer-
Planer Assembly.
Refer to Figure 7:
1. Select two legs (SE), one short stand top
support (SD) and one short support plate (SB).
2. Attach one end of the stand top support (SD)
to the top of the first leg with two carriage bolts
(SG), flat washers (SH), lock washers (SJ) and
hex nuts (SK). Attach the other end of the
stand top support (SD) to the second leg in the
same manner. Hand-tighten only at this time.
3. Attach a support plate (SB) to each leg (SE) in
the same manner with two carriage bolts (SG),
flat washers (SH), lock washers (SJ) and hex
nuts (SK). Hand-tighten only at this time.
4. Repeat steps 1–3 using the remaining legs,
short stand top support and support plate.
5. Complete the stand construction by attaching
long stand top supports (SE) and long support
plates (SA) to the leg assemblies constructed
in steps 1–4. Hand-tighten all hardware only at
this time.
6. Place a rubber foot (SQ) on a hex cap screw
(SF), then insert the threaded end of the screw
through the opening on the bottom of the leg.
7. Secure with flat washer (SH) and hex nut (SK).
8. Attach rubber feet to remaining legs in the
same manner.
9. Place stand upright. Ensure that the stand is
on a level surface and all four legs are
contacting the surface.
10. Tighten all hex nuts with the 10mm
wrench (X, Figure 4) provided.
7.2 Mounting Jointer-Planer to Stand
Refer to Figure 8:
1. Place the Jointer-Planer (D) onto the
assembled stand and secure with 4 socket
head cap screws (SM), lock washers (SP), and
flat washers (SN).
2. Tighten all socket head cap screws (SM) with
the 5mm hex wrench (W, Figure 4) provided.
Figure 7
Figure 8
SK
SA
SB
SC
SD
SE
SK
SJ
SH
SK
SH
SJ
SG
SG
SH
SQ
SF