installation manual

14
To Convert Surface Burners
1. If installed, remove the burner grates.
2. Remove burner cap.
3. Remove the burner base by rst removing (2) T-20 screws.
A
C
B
Burner
A. Burner cap
B. Screws
C. Burner base
4. Apply masking tape to the end of a 1/4" (7 mm) nut driver
to help hold the gas orice spud in the nut driver while
changing it. Insert nut driver into gas opening and press
down onto the gas orice spud, and remove by turning the
gas orice spud counterclockwise and lifting out. Set gas
orice spud aside.
5. Replace with correct Propane gas orice spud. See the
“Propane Gas Orice Spud/Hood Chart.”
Burner orifice spud
Use the following chart to nd the exact orice spud placement.
Propane Gas Orifice Spud/Hood Chart
Burner
Rating
Stamp Size Burner Style
7,400 BTUs 70
44
0.70 mm
0.44 mm
Small burner - main
Small burner - simmer
13,000 BTUs 99
50
0.99 mm
0.50 mm
Large burner - main
Large burner - simmer
16,000 BTUs 116 1.16 mm Grill burner
NOTE: Refer to serial tag for more information on burner ratings
and locations.
6. Place Natural gas orice spuds in plastic parts bag for future
use and keep with package containing literature.
NOTE: There may be extra orices in your kit.
7. Replace the burner base and screws. Tighten screws only
until burner is snug to cooktop, do not over-tighten.
8. Replace burner cap.
9. Repeat steps 2 through 8 for the remaining burners.
10. Remove the control knobs and bezels for surface burners
and grill.
NOTE: For oven controls and griddle controls, no changes
are needed.
Adjusting Simmer Low Setting on Surface Burner for
Propane
1. Locate the Simmer low-turndown adjustment screw through
the bezel on the left side of the ignition switch.
2. With the burner ON, and set to Simmer Lo, adjust the
simmer ame down to the proper BTU level. Using a
1/8" x 4
1
/
4
" (3.2 mm x 108 mm) at blade screwdriver, turn
the simmer low-turndown adjustment screw clockwise until
the ame height is below the bottom of the cap. If the ame
becomes unstable and ickers or appears to race around the
burner, the adjustment is too low and the screw should be
adjusted counterclockwise until the ame is stable. Repeat
this step for all surface burners, except the grill burner.
NOTE: Use a knob to adjust the burner valve.
NOTE: If your cooktop has the IR grill, then skip ahead to
Convert IR Grill Burner section.
3. Replace the bezels using the 2 screws which attach to the
valve brackets.
NOTE: Make sure no wires are pinched when reinstalling
bezels.
4. Push the surface knobs onto the valve stems.
5. Replace burner grates.
To Convert IR Grill Burner for Propane
1. Unplug or disconnect power.
2. Remove the grill knob and bezel. The other surface knobs
and bezels should be off the cooktop.
3. Remove the two screws on each side of the cooktop that
hold the control console in place.
4. Gently lift and pull console off. Place console on covered
surface to avoid scratching.
A
B
A. Size stamp
B. Fuel type stamp (L for Propane or
N for Natural gas)
AB
A. Simmer low-turndown adjustment screw
B. Ignition switch
Console attachment
screws (2 per side)
Do not remove
this screw