Use and Care Manual

CARE AND MAINTENANCE
Interior and Exterior Doors (JCM005)
4
CLEANING GLASS
DOOR SURFACE CLEANING AND HARDWARE LUBRICATION
Cleaning and lubrication help to maintain and restore smooth operation to movable parts such as hinges and locksets and, in most cases, offers
some corrosion protection.
GENERAL CLEANING
Prepare cleaning solution (1 tsp. baby shampoo to one gallon of
water or 1-1/2 cups vinegar to one gallon of water).
1. Rinse surface with clean water from top to bottom.
2. Clean with mild soap and water and sponge or soft brush with
uniform pressure horizontally, then vertically.
3. Promptly rinse thoroughly with clean water (sponging while
rinsing may be helpful; do not allow cleaning solution to dry on
the surface or collect and puddle).
4. Wipe dry with lint-free dry cloth.
5. If necessary, repeat steps above until clean.
6. Dry door with separate cloth.
PAINT REMOVAL
1. Soak dried latex paint drips with warm water and baby shampoo
solution. For oil-based paint, consult a paint professional.
2. Wipe with damp cloth or sponge.
If needed,
3. Scrape gently with plastic putty knife. Repeat soak and scrape.
4. Repeat if necessary.
LABEL REMOVAL
Slowly peel from one corner. If label tears or sticks, moisten with
soapy water and gently scrape with plastic putty knife. Stubborn
labels can be soaked with soapy water and covered overnight with
plastic wrap. Gently remove with plastic putty knife.
STUBBORN STAIN REMOVAL
Commercial glass cleaning products may be necessary.
• Apply small amount directly to the stain. Avoid spilling or
dripping down the glass.
• Some persistent stains may need higher strength cleaning
solutions that contain active ingredient chemicals such as
denatured alcohol or acetone. Special care must be taken when
using these types of cleaners.
• For oil and grease: try baking soda and water.
MORE INFORMATION ON GLASS CLEANING
• The Glass Association of North America (GANA):
www.glasswebsite.com
Note on Web sites! Web site content is subject to change and
should be used for informational purposes only. JELD-WEN is not
responsible for third-party information.
Clean door surface and maintain hardware any time doors are not
opening or closing properly or at least biannually (monthly for
coastal areas):
• Clean dirt/debris with mild soap and water and rinse clean
• Tighten loose screws
• Replace damaged hardware
PRECAUTIONS
The following substances may damage protective nishes. Do not use:
• Vinegar-based cleaners (use on glass only)
• Citrus-based cleaners (lemon, etc.)
• Paint removers
• Window cleaners
• Brick/siding washes
• Any other industrial or abrasive cleaners
1. Lubricate hinges with light oil
(3-In-One
®
oil or equivalent) annually
or when noisy.
2. Spray keyway lock with
graphitelubricant.
FOLDING DOORS:
Tracks and Bearings
Wipe visible track surfaces with a damp soft cloth and a mild
detergent, then wipe dry with a clean cloth. Using a suitable applicator
spread a small amount of clear petroleum jelly or similar lubricant
where the carrier wheels pass so that it is distributed evenly along the
track. Place additional lubricant around the bearings. The lubrication
reduces wear, improves operation and protects against corrosion. In
severe environments, apply a thin lm of WD40
®
.
Hangers, Pivots and Brackets
Exposed surfaces should be wiped down with warm soapy water
and a soft rag, and then rinsed clean before applying new surface
protectant. A light spray application of WD40
®
, followed by a light
wipe with a dry cloth to remove any excess.
Hinges
Wipe down the visible surfaces with warm, soapy water and a soft
rag, then rinse off and dry by wiping with a clean rag. Application
of a thin lm of WD40
®
will help maintain the original luster of the
metal nish, and lubricate the moving contact surfaces. Be careful
not to get these compounds on any wood components as it may
cause staining. For oil-rubbed bronze nish, care should be taken
when cleaning or re-applying surface protectant.
Flushbolts
Spray WD40
®
to the sliding pin inside the bolt and to the lock
cylinder. There are access holes or slots on all drop bolts so that this
can be completed without removing the locks from the doors.