Instructions / Assembly

ManualsBrandsJELD-WEN ManualsDoors & Windows71-1/4 in. x 79-1/2 in. W-2500 Arctic Silver Left-Hand Clad-Wood Sliding Patio Door with Brilliant White Interior

INSTALLATION INSTRUCTIONS

for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026)

LANDINGS

These instructions

cover two patio door

sill conditions: the

step-down landing

and the continuous

slab landing. The

installation methods

vary slightly between

landing types.

Please allow sufcient time to properly prepare the rough opening,

install the patio door, and ensure its proper operation.

Newer construction methods have led to an increase in air and water

tightness in buildings. This frequently leads to negative air pressure

inside the home, which can draw water through very small openings.

Our installation method seals the patio door to the weather barrier

(typically building wrap) and uses a sill pan to capture and drain

incidental water from under the patio door.

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for wood patio doors with

exterior trim or nailing n. Read these instructions thoroughly before

beginning. They are designed to work in most existing applications,

however; existing conditions may require changes to these

instructions. If changes are needed, they are made at the installer’s

risk. For installations other than indicated in these instructions, contact

a building professional.

Not all patio door types may be installed into every wall condition in all

areas. Consult your local building code ofcial for applicable building

codes and regulations. Local building code requirements supersede

recommended installation instructions.

Please Note! Any patio door installation where the sill is higher than

35 feet above ground level or into a wall condition not specically

addressed in these instructions must be designed by an architect or

structural engineer. Failure to install square, level and plumb and on a

at surface (without twist or warp) could result in denial of warranty

claims for operational or performance problems.

Note to Installer: Provide a copy of these instructions to the building

owner. By installing this product, you acknowledge the terms and

conditions of the limited warranty as part of the terms of the sale.

GLOSSARY

Applied Nailing Fin

A mechanically attached vinyl n that creates a ange around the

perimeter of the patio door and is used to position the patio door in

the rough opening.

Backer Rod (backing material)

A material (e.g. foam rod), placed into a joint primarily to control the

depth of the sealant.

Buck

A wood framework attached to the masonry inside a window or patio

door rough opening.

Mulled Unit

Two or more door units structurally joined together.

Pilot Hole

A drilled hole that is no larger than the body of the screw (minus the

threads).

Shiplap

The layering method in which each layer overlaps the layer below it so

that water runs down the outside.

IMPORTANT INFORMATION & GLOSSARY

Estimated Install

Time for New

Construction

First Time: 4.0 hr.

Experienced: 2.5 hr.

Professional: 1.5 hr.

Step-Down Landing

Continuous

Slab

Landing

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s recommended installation instructions for wood patio doors with exterior trim or nailing fin. Read these instructions thoroughly before beginning. They are designed to work in most existing applications, however; existing conditions may require changes to these instructions. If changes are needed, they are made at the installer’s risk.
PAGE 2
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) Rough openings This installation guide specifically addresses masonry/block wall, sheathed wall and open-stud construction. MASONRY/BLOCK WALL CONSTRUCTION This installation assumes that a building professional has already properly fastened and sealed a framework of studs (often called a buck) to the concrete/ masonry wall.
PAGE 3
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) 1 remove packaging & Inspect patio door INSPECT PATIO DOOR REMOVE PACKAGING • Cosmetic damage Remove shipping materials such as corner covers, shipping blocks or pads. Remove the skid board attached to the bottom of the door and save screws for securing the sill. Remove any staples exposed on the frame, but leave any glass protective films on.
PAGE 4
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) 4 install sill pan If installing into masonry: 1. Cut a piece of selfadhesive flashing the length of the sill. 2. Cut a notch out of each end and apply to the sill as shown. Both installations: 1. Set the sill pan in the rough opening, aligning the front edge (for continuous slab,) or folded down edge (for step down) with the exterior of the rough opening.
PAGE 5
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) 6 prepare stud-framed wall FOR RETROFIT INSTALLATIONS After removing the old patio door, remove sufficient siding to expose at least 9" of intact building wrap. If damaged, apply new building wrap in a shiplap manner. Verify header and trimmer studs are structurally sound. PREPARE BUILDING WRAP Verify these steps do not void the building wrap manufacturer’s warranty. 1.
PAGE 6
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) 8 install patio door Warning! To avoid injury, use at least two people to install. Adequately support the door until fully installed. 1. Apply a 3/8" continuous bead of sealant across Sealant the sill pan back dam and over the flashing joints as shown. 2. Tilt patio door into the rough opening. Make sure the back of the door makes solid contact with the sealant. 3.
PAGE 7
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) 8 install patio door - continued 4. Fill any holes in the sill with sealant. 5. If the hardware pack Exterior contains 2 #8 x 2" pan head screws, remove the two vertical screws in the stationary panel head Head bracket and replace bracket with the provided #8 x 2" screws. The replacement screws should penetrate shims. Add shims between the door frame and rough opening if necessary. 6.
PAGE 8
INSTALLATION INSTRUCTIONS for Wood Patio Doors with Exterior Trim or Nailing Fin (JII026) 10 COmPlETE INsTAllATION - CONTINUED 4. Ensure sealant on back dam of the sill pan fully seals to the inside face of the sill. Apply more sealant as necessary. 5. Install lockset hardware per supplied instructions. 6. some French double door units may require installing lock bolts at the top and bottom of the inactive panel. locate the center point of each lock bolt, drill 3/8" bolt holes and install keeper plates.