Installation Instructions

INSTALLATION INSTRUCTIONS
for Vinyl Casement Window Opening Control Devices
(JII038I)
This device complies with ASTM F2090-10
Sash preparation and arm attachment:
Caution! The following step may require working from
the outside or removing the sash. Please work safely. If
removing sash, consult the casement window Product Guide
at www.jeld-wen.com/resources for proper procedures.
1. Open sash. Using the
provided template,
mark screw hole
locations for the
bracket on the
vertical section of
sash in the same
location as the hinge
pocket.
2. Pre‐drill 3/32" screw
holes 1/2" deep
where marked.
3. Attach bracket in orientation shown, with two of the
provided screws.
The information contained herein is provided solely for informational and/or educational purposes. JELD-WEN disclaims any and all liability associated with the use
and/or provision of this information. Any reliance upon the information or advice is at the risk of the party so relying. The information contained herein may be
changed from time to time without noti cation.
© 2012 JELD-WEN, inc. | JELD-WEN, the JW icon and Reliability for real life are trademarks or registered trademarks of JELD-WEN, inc., Oregon, USA.
Thank you for selecting JELD-WEN products. Thoroughly
read these instructions and understand the operation of this
device. Failure to properly install device may allow window
to open unexpectedly allowing falls through the window.
Provide the safety and operating instructions to the
homeowner and occupant after installation is complete.
Contact us for additional copies if needed.
The window opening control device is designed to limit
the opening of the window, and must be installed so that
objects no larger than a 4" rigid sphere will  t through the
opening. This is to protect against accidental falls from an
open window, but is not a substitute for traditional safety
practices.
IMPORTANT SAFETY INFORMATION
• Train all occupants six (6) years old and older to operate
the release mechanism in case of an emergency.
• The window opening control device engages
automatically when the window is closed.
• Check for re-engagement of window opening control
device after each release.
• Test once a month for proper operation and inspect for
damage. Replace device promptly if necessary.
• Make sure the device is properly installed, engaged, and
operated as speci ed. Do not modify the device in any way.
(05/12)
E
D
G
E
O
F
S
A
S
H
B
O
T
T
O
M
1
.
A
T
T
AC
H
F
LUSH TO
2
.
P
L
ACE
A
GAINST
E
D
G
E
OF
H
I
NGE
P
OC
K
ET
O
N
V
ERTICAL
S
ASH
M
EMBE
R
3. M
AR
K
C
E
NTERS
O
N
SA
S
H
4
.
D
RI
LL
3
/
32" X
1
/
2"
D
E
EP
I
N
S
A
S
H
AT
M
A
R
KS
Template
Outside
edge of
sash
Window
frame
Bracket
with arm
Tools required:
• Phillips screwdriver
• 3/32" drill bit and drill
Kit includes:
• Track
• Bracket with arm
• 4 - #7 x 1/2" screws
• Installation template
1.
CRANK TO
OPEN
WINDOW
SLIDE
COVER
ROTATE
TAB
2.
3.
4.
Track
Sash
Window
frame
• Consult local building and  re codes before installing
this device; contact local building code department or
 re department for speci c codes. Install device such
that the release mechanism(s) is in conformance with
local building and  re code requirements.
WARNING
Possible Fall Hazard
• Young children may fall out of the window if this
device is not installed correctly. Install the device so
that a rigid 4.0-in.-diameter sphere does not pass
through any space in the window opening after the
device is in place.
• Young children may fall out the window if all
installation instructions are not followed:
• Use recommended materials and techniques.
• Make sure the fall prevention device is securely
attached to the window frame.
• Make sure that the window frame is in good
condition.
INSTALLATION
4. Be sure arm moves freely and hangs toward the inside of
the window at an approximate 20
o
angle from vertical.
Frame preparation and track attachment:
1. Position track on
vertical section of
frame in the same
location as the hinge
pocket against the
sill in the position
shown. Mark track
hole locations on the
frame.
2. Pre‐drill 3/32" screw
holes 1/2" deep
where marked.
3. Attach track in
orientation shown, with two of the provided screws.
4. Operate window and verify device performs correctly.
Immediately  x any problems.
5. Place the included label on the top of the operator
housing between the crank arm and window frame or
other visible location when the window is closed.