Specification

PRODUCT GUIDE
Interior & Exterior Doors (JPG013)
3
HARDWARE REPLACEMENT & ADJUSTMENT
HARDWARE TYPES
Metal hardware offers functionality, aesthetic appeal and resistance •
to corrosion but is not totally corrosion proof.
Plastic hardware offers high resistance to the elements however, over •
time it can deteriorate from ultraviolet light, heat, cold, and chemical
exposure.
Brass hardware has a special protective lm to reduce/eliminate •
polishing and requires special care.
See our complete Care and Maintenance document at •
www.jeld-wen.com/resources for more information on cleaning and
lubricating hardware.
Screw hole repair and hardware alignment, or realignment, are
common tasks for any hardware replacement component. Follow these
instructions if screw holes become stripped and/or if hardware no
longer functions properly due to misalignment.
SCREW HOLE REPAIR (IN WOOD ONLY)
1. Cut wooden toothpicks or appropriate sized wood dowel to t screw
hole just below wood surface.
2. Fill screw hole with wood glue.
3. Insert toothpicks or dowel; let dry.
4. Fill to surface with wood putty; let dry.
5.Sandsmoothandrenish;letdry.
6.Drillnewpilothole.
HARDWARE ALIGNMENT (IN WOOD ONLY)
Misalignment can happen if screws have become stripped and cannot
be tightened. This alignment will create new screw holes.
1. Remove hardware.
2. Repair screw holes according to the procedure above.
3. Mark new screw holes as follows:
Lay hardware in position and hold in place.•
Mark new screw locations through screw holes.•
Remove hardware and set aside.•
4.Drillpilotholeswith1/16"drillbitatnewmarkedscrewhole
positions no deeper than screw length.
5.Installhardware.
6.Testoperation;ifnotoperatingproperly,callusforassistance.
HINGE REPLACEMENT AND ADJUSTMENT
REPLACEMENT
1. Remove slab.
2. Remove hinge plates from slab.
3. Repair screw holes as instructed above if stripped.
4. Install new hinge plates in the same locations.
5.Reinstallslab.
HINGE REPLACEMENT AND ADJUSTMENT - CONTINUED
ADJUSTMENT (SPRING HINGES ONLY)
1. Close door.
2. Insert the provided
hex wrench so that
it can be rotated
clockwise.
3. Rotate hex wrench
1/4 turn and insert
tension pin loosely
into tension hole.
4. Remove hex wrench
and try closing force.
5. Repeatstepsuntil
closing force is
adequate but do not
rotatepast3holeson180
o
openingsor4holeson90
o
openings.
BLINDS BETWEEN THE GLASS
For easiest operation, keep the slats in a fully open position while operating.
ADJUSTMENTS
1. If the operator comes off of the track, hold the operator at a sharp
angle to the glass and reinsert the two legs under the track opening.
2. Re-couple the operator magnets.
RE-COUPLE OPERATOR MAGNETS
1. Slide the operator past the half-way engagement point until the rst
click.
2. Full travel blinds will fully engage when you hear the rst click. Half
travel (those units with a single side operation) will require you to
continue moving the operator up until you hear the second click. This
will ensure the magnets are fully engaged.
MECHANISM REPLACEMENT
RAISE & LOWER MECHANISM
1. Place a piece of cardboard between the slide mechanism and the
glass to help release the magnets.
2. Tilt the mechanism toward you, and remove the mechanism. It may
require a strong tug to break the magnetic bond.
3. Before replacing the new slide mechanism, ensure the glass is clean.
4. Insert the tabs underneath the lip of the inner frame and raise the
slide to the top until the magnets engage.
a. Full travel blinds will fully engage when you hear the rst click.
b. Half travel (those units with a single side operation) will require
you to continue the travel of the operator up until you hear the
second click. This will ensure the magnets are fully engaged.
5.Checkforproperoperation.Removeandreinstallifnecessary.
TILT MECHANISM
1. Move the top helix to the left side. Moving the slider magnet on the
outside of the glass can do this. The helix tilt operator has a magnet
set which will follow the magnet inside the slide mechanism.
2. Clean the glass attaching area.
3. Peel off the tape on the back of the slider.
4. Before application, push the magnet to the left of the slider. Ensure
the slider is facing the right direction (there is a long horizontal gap
at the top that allows the magnet housing to slide along the base).
5.Letthemagnetbeattractedtotheleftsideofthemagnet,whichis
inside the glass. Make sure the slide is horizontal.
6.Pushtheslideagainsttheglassrmlyonthetapearea,asthe
adhesive works under pressure.
Tension
pin
Tension
hole
Clockwise