DESIGNER/LUXURY BATH SERIES INSTALLATION / OPERATION INSTRUCTIONS Save These Instructions for Future Use. Complete and mail-in the product registration card provided with your unit. Write and save the model and serial number of your unit below.
ENGLISH IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER: — TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS UNIT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES. WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL.
INSTALLATION INSTRUCTIONS FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMIT ACCESS FOR SERVICING. THIS UNIT SHOULD BE ELECTRICALLY GROUNDED AND INSTALLED BY A LICENSED CONTRACTOR, ELECTRICIAN, AND PLUMBER. BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT. A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND HEATER TO PERMIT CONNECTION OF AN NO. 8 AWG (8.
CONTENTS ENGLISH Safety Instructions _____________________________________________________________________ 2-3 Contents _____________________________________________________________________________ 4 Specifications _________________________________________________________________________ 5-8 Roughing-in Reference _________________________________________________________________ 9-13 Installations Instructions _________________________________________________________________ Framing and Support ____________
SPECIFICATIONS Important: Read complete instructions before beginning installation. Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only. Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the bath.
SPECIFICATIONS ENGLISH SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand ALLUSION™ 6636 ALLUSION™ 7236 TOTAL WEIGHT/ FLOOR LOADING OPERATING GALLONAGE 66" 36" 26" (1676 mm) L 17-3/8" (441 mm) A ( 914 mm) W 11-15/16" (210 mm) B ( 660 mm) H Template Provided P/N BY20000 843 lb (383 kg)/ 51 lb/ft2 (248 kg/m2) Min - 55 U.S. gal (208 liters) Max - 75 U.S.
SPECIFICATIONS OVAL & ROUND BATHS A W 1/2" (13 mm) H (Heater) ENGLISH MAX. 2-1/2" L B DRAIN/OVERFLOW SIDE VIEW (Motor) END VIEW DUETTA™ MAX.
SPECIFICATIONS CORNER BATHS ENGLISH MAX. 1/2" H (Heater) W 2" (51 mm) A B END VIEW SIDE VIEW DRAIN/OVERFLOW BELLAVISTA™ CORNER, Right Hand SPECIFICATIONS (Corner) LH = Left Hand, RH = Right Hand MODEL DIMENSIONS (1524 mm) L BELLAVISTATM 60" CORNER 60" (1524 mm) W 21-3/4" ( 553 mm) H RH DRAIN/OVERFLOW DIMENSIONS 18-7/8" (479 mm) A 14" (356 mm) B CUTOUT Template Provided P/N P654000 TOTAL WEIGHT/ OPERATING PRODUCT FLOOR LOADING GALLONAGE WEIGHT 1046 lb (475 kg)/ 42 lb/ft2 (205) kg/m2 80 U.
ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (RECTANGULAR) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 66" 36" 8-1/2" Heater Motor 36" 5" x 5" 8-1/2" Heater 11-15/16" 33" ALLUSION™ 6636, Right Hand 11-15/16" Opt. Service Access 12" H x 18" L Service Access 12" H x 18" L Service Access 60" Motor 5" x 5" 8-1/2" Heater Opt.
ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (RECTANGULAR) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. ENGLISH 60" 21" 60" 12" x 4" 12" x 4" Motor 4.2" 2" Motor 42" 42" Heater Opt. Service Access 12" H x 18" L Service Access 12" H x 18" L Service Access ELARA™ 6042 Left Hand 18 " 12" x 4" Heater 12" H x 18" L Service Access 2" Opt. Service Access 12" x 4" 2" 4.2" 10.6" Opt. Service Access Motor Opt.
ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (RECTANGULAR) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 5-1/4" 10-1/2" Heater 36" 3" Motor 18" x 4" 47" 3" Heater 3" 7" Opt. Service Access 10-1/4" 36" SABELLA™ Right Hand REÁL™, Right Hand 13-3/4" 3" 1" 72" 12" H x 18" L Service Access 14" 18" x 4"* 12" H x 18" L Service Access 42" 1" Motor ENGLISH 72" Opt.
ROUGHING-IN REFERENCE Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 66" 60" 42" Motor 2" Heater 3.84" 30" 13" x 4" 36" 3.84" 33" DUETTA™ 6042, Right Hand 2" Motor Heater 3.84" 33" Opt. Service Access 72" Motor 42" Heater 3-1/2" 11" Opt. Service Access 11.04" 12" H x 18" L Service Access 14" x 4" 12" H x 18" L Service Access 13" x 4" 11.04" DUETTA™ 6636, Right Hand 66" 42" Motor Heater Opt.
ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (ROUND, CORNER) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. ENGLISH 60" 60" 59-1/2" Ref. 14"x5"* Service Access Motor 12"x4" 72" 5" 16" 26" 34-9/16" Heater Heater Opt. Service Access 16" Motor 3" 77-3/4" 7-1/2" 4" 9" 12" H x 18" L Service Access 72" BELLAVISTA™ CORNER, Right Hand CORTINA™, Right Hand NOTE: 1.
INSTALLATION INSTRUCTIONS ENGLISH Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to the table under total weight for your model. The unit must be supported from the bottom of the bath and not from the bath rim or tile flange. If the subfloor is level and a continuous surface, no other preparation is necessary.
INSTALLATION INSTRUCTIONS Service Access The Duetta Whirlpool baths should access as shown below. For partially or fully sunken installations, allow for access to service connections. It is the installer's responsibility to provide sufficient service access. The recommended minimum dimensions allowable for service to the bath are shown in the "Service Access" illustration. Provide adequate area around unit for air circulation for cooling the motor and to supply sufficient air to the jets.
INSTALLATION INSTRUCTIONS The installation clearance recommendations below are to ensure that installers have enough space to maneuver and insert tub. The Designer/Luxury line whirlpool tubs have electrical, plumbing and lighting systems installed. Do not lift the bath by the plumbing or wiring at any time; handle by the shell only.
INSTALLATION INSTRUCTIONS Installation See END/SIDE VIEW in Begin Installation Optionally, use a washable marker to scribe a reference line 1" (25,4 mm) outside the cutout edge on the deck surface. This may assist in final alignment of the tub. TUB CUTOUT Install any trim kits, faucets, or other tub components before installing. REFERENCE LINE 1/2" To install unit insert the motor/pump end first when lowering the tub into the cutout opening as shown in the bottom illustration.
INSTALLATION INSTRUCTIONS ENGLISH Electrical Connections Separate circuits, each must be protected by a Ground Fault Circuit Interrupter (GFCI), are required for the pump/ motor and the RapidHeatTM Heater. Refer to the electrical specification for each model on pages 6-8. Install duplex outlets to the studwall underneath the bathtub, at least 4 inches (10,2 cm) above the floor or in accordance with local building or electrical codes. Duplex outlets are not provided.
Plumbing and Water Supply Water Supply A drain/overflow assembly (sold separately) must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage and verify that the kit is of the proper finish. In the Jacuzzi Whirlpool Bath drain/overflow kit, note that the waste flange, strainer, overflow cover and cover screws are packaged in a separate package within the kit to protect the trim finish.
OPERATING INSTRUCTIONS ENGLISH OPERATION NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features discussed in this instruction pamphlet apply to all baths. All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools or spas.
OPERATING INSTRUCTIONS (cont'd) Electronic Control Panel Operation (with optional Chromotherapy/Illumatherapy TM lighting) All tubs in this product line come with electronic controls and standard Chromotherapy or IllumatherapyTM. Read and follow the operation instructions for the control system of your unit. This Jacuzzi tub is equipped with a seven button electronic control panel.
OPERATING INSTRUCTIONS (cont'd) ENGLISH RapidHeatTM These units have a RapidHeatTM heater installed on the intake or discharge lines. The heater will help maintain the temperature of the water in the bath. Operation With the heater installed and the whirlpool pump is operating, the heating function is totally automatic. No user control required.
MAINTENANCE INSTRUCTIONS Purging the Whirlpool System To clean your bath, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable. Never use abrasive household cleaners on any Jacuzzi Whirlpool Bath product.
MAINTENANCE INSTRUCTIONS SUCTION COVER/STRAINER ASSEMBLY ENGLISH Suction/Intake Cover/Strainer Maintenance Clean the suction/intake cover/strainer of hair and debris when necessary. To do this, remove the center screw and detach the square cover. Clean the cover by backflushing debris from the holes. Replace the suction/intake cover immediately after cleaning. When reinstalling, orient the cover/ strainer with the small notch at the bottom.
General Whirlpool Bath Troubleshooting Guide PROBLEM REMEDY No power to pump/motor. Reset GFCI. Pump/motor not plugged in. Insert plug fully into outlet. Pump/motor faulty. Replace pump/motor assembly. Jets are closed. Open jets by rotating counterclockwise. Control panel cable disconnected. Reconnect control panel cable at control or junction box. Pump/Motor operates but no fully adjustable jets are functioning. Suction cover may be clogged.
ADDENDUM 8-Button Electronic Control Panel for the 240 V Control System ELECTRICAL REQUIREMENTS The Addendum for the 8-button Electrical Control Panel is attached to the Luxury® Salon™ Installation and Operation Instructions, EL21000B. It provides the electrical requrements for the 240 V Control Systems.
The following details will replace information found in the Combination Air Bath and Whirlpool Installation and Operation Instructions, BR28000B (4/05) manual. CAUTION: Install all electrical services on the right side of the bath. The blower has been moved from the left side to the right side, next to the pump motor. NOTE: The following art replaces the similar art found on Page 1 of the Combination Air Bath and Whirlpool manual.
ENGLISH AUTHORIZED SERVICE If you need a referral for a service company near you, or need assistance with operation or maintenance related questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/ for products and services. To find service agent listings for: Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.
Jacuzzi Whirlpool Bath Limited Warranty Designer/Luxury Collection Bath Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its sole option, the unit or its equipment in accordance with the following terms and conditions.
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit must not be installed.