CHEMICAL SANITIZING GLASSWASHER DISHMACHINE SERIES TECHNICAL MANUAL INSTALLATION MANUAL FOR EXPORT UNITS SERVICE MANUAL FOR DOMESTIC UNITS FOR JACKSON MODELS: Delta 1200 March 21, 2013 P/N 07610-003-62-15 Revision G JACKSON WWS, INC. P.O. BOX 1060 HIGHWAY 25E BARBOURVILLE, KY. 40906 FAX: (606) 523-9196 PHONE: (606) 523-9795 www.jacksonwws.
REVISION REVISION DATE MADE BY APPLICABLE ECN A 10-27-08 CW B 11-10-08 GS C 06-05-09 ARL 90605-1430-MD Updated electrical schematic. D 02-10-10 RLC 091106-1526-CW Corrected part number on page 36 DETAILS Initial release of manual. 8074 Revised Drawings.
NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL GLASSWASHER SERIES Delta 1200 = 24” Glasswasher Model: Serial No.: Installation Date: Service Rep. Name: Phone No.
TABLE OF CONTENTS SECTION I. DESCRIPTION PAGE GENERAL Specifications Dimensions 2 3 INSTRUCTIONS SECTION Installation Instructions Electrical Connections Detergent Control Chemical Dispensing Operating Instructions Sequence of Operation 5 6 7 8 9 10 III. PREVENTATIVE MAINTENANCE 11 IV. TROUBLESHOOTING SECTION 13 V.
SECTION 1: SPECIFICATION INFORMATION 1
SECTION 1: SPECIFICATION INFORMATION SPECIFICATIONS Delta 1200 OPERATING CAPACITY (RACKS/HOUR) GLASSES PER HOUR 1200 OPERATING CYCLE (SECONDS) TOTAL CYCLE TIME 120 TANK CAPACITY (GALLONS) 3.
SECTION 1: SPECIFICATION INFORMATION MACHINE DIMENSIONS 25.25" 9.50" 5.00" Ø1.5 Drain Connection Water Inlet 1/2" I.P.S. Cold 25.00" Water Inlet 1/2" I.P.S. Hot 14.64" 12.86" 8.64" SECTION B-B SCALE 0.09 : 1 27.41" 25.38 2.00" Wall Clearance A 19.45" 12" VERTICAL CLEARANCE 29.26" B B 6.59" Drain A 05700-003-60-00 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 3 6.17" Inlet SECTION A-A SCALE 0.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS 4
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS INSTALLATION INSTRUCTIONS VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indicator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undamaged condition.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS ELECTRICAL CONNECTIONS trap is required by code, it should have a flow capacity of 5 gallons per minute. are marked on the terminal block. Install the grounding wire into the lug provided. Tighten the connections. It is recommended that “DE-OX” or another similar anti-oxidation agent be used on all power connections. WATER SUPPLY CONNECTION: Ensure that you have read the section entitled “PLUMBING THE DISHMACHINE” above before proceeding.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS DETERGENT CONTROL Detergent usage and water hardness are two factors that contribute greatly to how efficiently your dishmachine will operate. Using detergent in the proper amount can become, in time, a source of substantial savings. A qualified water treatment specialist can tell you what is needed for maximum efficiency from your detergent, but you should still know some basics so you’ll understand what they are talking about.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS CHEMICAL DISPENSING EQUIPMENT TO PREPARE PUMPS FOR OPERATION The Delta 1200 is supplied with detergent, rinse additive and sanitizer dispensing chemical feeder pumps. Locate the open ends of the chemical tubes with the tube stiffeners and place each one in the appropriate container. A. Red Tubing = Detergent B. Blue Tubing = Rinse Aid C.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS OPERATING INSTRUCTIONS TO FILL MACHINE WITH WATER: 1. Remove wash tank strainer and place overflow stopper into fitting at the bottom of the wash tank. 2. Open incoming water shut-off valves on cold and hot water lines. 3. Place the power switch to the “FILL” position, machine will automatically fill to the correct level. 4. Check water level, it should be near top of the overflow stopper. 5. Replace wash strainer. TO RUN THE MACHINE: 1.
SECTION 3: PREVENTATIVE MAINTENANCE 10
SECTION 3: PREVENTATIVE MAINTENANCE PREVENTATIVE MAINTENANCE The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However, this does not mean that some items will not wear out in time. Jackson highly recommends that any maintenance and repairs not specifically discussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY.
SECTION 4: TROUBLESHOOTING 12
SECTION 4: TROUBLESHOOTING COMMON PROBLEMS Inspection, testing and repair of electrical equipment should only be performed by a qualified service technician. Many of the tests require that the unit have power to it and live electrical components be exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE. Problem: Dish machine will not run, no voltage at wash relay terminals L1 and T1. 1. Electrical power not installed to machine, service (main) power disconnect off.
SECTION 4: TROUBLESHOOTING COMMON PROBLEMS Problem: Low wash water pressure at wash arm spray nozzles. 1. Pump impeller worn or broken. Replace pump. 2. Clogged jets in wash arms. Clean out wash arms. 3. Float stuck on float switch. Remove, clean and reinstall float switch. 4. Water level too low in the wash tank. Ensure that the incoming water line flow pressure meets the requirements on the dishmachine data plate. Problem: Machine keeps tripping service breaker. 1. 2. 3. 4.
SECTION 4: TROUBLESHOOTING COMMON PROBLEMS Problem: Rinse aid pump not feeding, detergent feeds okay. 1. Faulty speed control board. Check operation of board. If not working properly, replace. 2. Defective hose or squeeze tube. Replace hose or squeeze tube as needed. Problem: Wash heater does not work. (Note: push wash heater contactor bar down and take amperage reading. Amps should be correct as stated on the dish machine data plate). 1. If no amp draw, check wash heater for continuity.
SECTION 5: SERVICE PROCEDURES 16
SECTION 5: SERVICE PROCEDURES REPLACING THE CHEMICAL FEEDER PUMP MOTOR Jackson glasswasher machines come equipped with chemical feeder pumps to ensure proper ware washing results. Occasionally, the motors operating these pumps may need replacing to maintain optimum performance. Jackson offers all of the repair parts necessary for performing this task. The instructions provided here are for maintenance personnel only. Unauthorized persons should not attempt any of the steps contained in these instructions.
SECTION 5: SERVICE PROCEDURES REPLACING THE CHEMICAL FEEDER PUMP MOTOR (CONTINUED) replaced. Refer to the parts section of the technical manual for information regarding part numbers for ordering new prime switches.) 6. Turn the cover over and using the phillipshead screwdriver, remove the cover to the pump requiring a motor change. Removing the priming switch wire Removing the front cover. 7. With the cover removed, gently pull out the rubber tube from inside the pump.
SECTION 5: SERVICE PROCEDURES REPLACING THE CHEMICAL FEEDER PUMP MOTOR (CONTINUED) 14. Place the roller and the rubber tube back in the pump casing. Place the pump cover back on and tighten down with the four screws you previously removed. 15. Reattach the power wire and the wire for the priming switch. 16. Put the cover back on the control box and secure with the two screws previously removed. 17. Ensuring that all non-essential personnel are clear of the area, restore power to the unit.
SECTION 5: SERVICE PROCEDURES WASH TANK HEATER REPLACEMENT Jackson glasswasher machines come equipped with heaters to ensure proper ware washing results. Occasionally, some of these components may need replacing to maintain optimum performance. Jackson offers all of the repair parts necessary for performing this task. The instructions provided here are for maintenance personnel only. Unauthorized persons should not attempt any of the steps contained in these instructions. STEPS 1. Remove the front door.
SECTION 5: SERVICE PROCEDURES WASH TANK HEATER REPLACEMENT (CONTINUED) 6. Next, use the ratchet and 1/2” socket to remove the heater mounting nuts. Removing upper (wash) strainer. Reaching into the wash tank. 7. Removing the heater may require that you reach into the wash tank, grasp it and give it a push out of the wash tank. Removing the heater nuts. 5. Using the 3/8” nutdriver, remove the nuts securing the heater wires to the heater. Then carefully pull the wires out of Pulling the heater out. 8.
SECTION 5: SERVICE PROCEDURES WASH TANK HEATER REPLACEMENT (CONTINUED) AFTER MAINTENANCE ACTIONS Service personnel may want to drain the machine and allow it to cool down. Secure power to the unit at the service breaker and then verify the torque of all fasteners covered in this instruction. SPECIAL NOTES Work performed on Jackson dishmachines by unauthorized or unqualified personnel may void the warranty.
SECTION 5: SERVICE PROCEDURES THERMOSTAT REPLACEMENT Jackson glasswasher machines come equipped with thermostats to ensure proper ware washing results. Occasionally, some of these components may need replacing to maintain optimum performance. Jackson offers all of the repair parts necessary for performing this task. The instructions provided here are for maintenance personnel only. Unauthorized persons should not attempt any of the steps contained in these instructions. STEPS 1. Remove the front door.
SECTION 5: SERVICE PROCEDURES THERMOSTAT REPLACEMENT (CONTINUED) ture is maintained in accordance with the specifications on the machine data plate. 4. Use the 7/16” combination wrench to loosen and remove the imperial brass fitting. Once this is complete, you should be able to completely remove the thermostat. 9. Replace the heater cover. 10. Replace the front door. 5. Take the new thermostat and place its probe in the new imperial brass fitting provided in your kit.
SECTION 5: SERVICE PROCEDURES WASH MOTOR REPLACEMENT Jackson glasswasher machines come equipped with wash pumps that have powerful motors attached to them to ensure proper ware washing results. Occasionally, these assemblies may require replacing to maintain optimum performance. Jackson offers all of the repair parts necessary for performing this task. The instructions provided here are for maintenance personnel only. Unauthorized persons should not attempt any of the steps contained in these instructions.
SECTION 5: SERVICE PROCEDURES WASH MOTOR REPLACEMENT (CONTINUED) Lifting up on the motor. Loosening the discharge hose clamp. 6. With the nuts removed, grasp the motor assembly and lift up on it to clear the mounting studs. Pulling the discharge hose out. Suction hose coming off when moving the assembly. 7. Turn the motor so that you will have access to the wiring cover on the back. Be careful not to pull or yank too hard as the motor is still connected to the unit by way of the power lines. 8.
SECTION 5: SERVICE PROCEDURES WASH MOTOR REPLACEMENT (CONTINUED) Position the assembly so that the suction hose is not kinked. 21. Replace and tightne down the nuts securing the bracket to the frame. 22. Tighten the clamps for the suction hose. 23. Connect the disharge hose to the tub and tighten down the hose clamp. AFTER MAINTENANCE ACTIONS Verify the operation of the new wash motor and pump assembly by running the unit for approximately 15 minutes. Check for leaks and corredt as necessary.
SECTION 6: PARTS SECTION 28
SECTION 6: PARTS SECTION CONTROL BOX ASSEMBLY 14 13 12 1 2 11 3 4 5 6 7 8 9 10 07610-003-61-14 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 29
SECTION 6: PARTS SECTION CONTROL BOX ASSEMBLY Number QTY Part Number Description 1 2 05975-011-49-03 Fitting 2 3 05975-011-65-51 Fitting 3 1 05700-003-56-00 Bracket 4 1 05910-003-43-01 Capacitor 5 1 05940-200-76-00 Ground Lug 6 1 05700-011-40-05 Seperator 7 1 05950-011-61-67 Transformer 8 1 05945-111-47-51 Relay 9 2 05945-002-74-20 Contactor 10 1 05700-003-55-38 Access Panel 11 1 09905-100-75-93 Decal, Warning, Disconnect Power 12 1 09905-011-68-99 Decal, C
SECTION 6: PARTS SECTION OUTER SHELL ASSEMBLY 05700-003-57-951 OUTER SHELL 05700-003-60-389 2 05975-210-03-00 05700-003-58-73 3 809905-003-57-30 08415-003-60-357 505700-003-60-39 05340-108-01-03 4 05930-011-61-69 6 07610-003-61-26 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 31
SECTION 6: PARTS SECTION OUTER SHELL ASSEMBLY Number QTY Part Number Description 1 1 05700-003-57-95 Outer Cover 2 1 05975-210-03-00 Grommett 3 1 05700-003-58-73 Access Cover 4 4 05340-108-01-03 Bullet Foot 5 1 05700-003-60-39 Switch Cover 6 1 05930-011-61-69 Power Switch 7 1 08415-003-60-35 Curtain 8 1 09905-003-57-30 Jackson Decal 9 1 05700-003-57-95 Curtain Rod Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 32
SECTION 6: PARTS SECTION CHEMICAL FEEDER PUMP ASSEMBLY 1 2 3 7 6 Detergent Kit 4 5 Sanitizer Kit Rinse Aid Kit 07610-003-61-19 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 33
SECTION 6: PARTS SECTION CHEMICAL FEEDER PUMP ASSEMBLY Number QTY Part Number Description 1 1 05700-003-87-08 14 RPM Peri-Pump 2 1 05700-003-55-29 Cover and Peri-Pump Assembly 3 1 05700-003-55-34 Cover only 4 1 06401-003-61-21 Sanitizer Tube Replacement Kit 5 1 06401-003-61-22 Rinse Aid Tube Replacement Kit 6 1 06401-003-61-23 Detergent Tube Replacement Kit 7 1 05700-011-65-21 Squeeze Tube Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05/21/2012 34
SECTION 6: PARTS SECTION RINSE ASSEMBLY 4 3 1 5 2 6, 7, 8 9 2 11 12 13 14 21 19 23 22 24 15 16 20 17 18 25 10 37 38 26 40 34, 39 27 28 7 29 35 33, 34 30 32 31 07610-003-61-05 WATER 36 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 35
SECTION 6: PARTS SECTION WASH ASSEMBLY Number QTY Part Number Description 1 2 1 09330-003-45-71 Upper Rinse Casting 2 05700-003-56-57 Rinse Arm 3 1 05700-003-45-71 Hose 4 1 05330-003-41-73 Grommett 5 2 05700-003-55-31 Vacuum Breaker 6 4 04730-011-61-57 Vacuum Breaker Nipple 7 6 05310-011-61-45 Hex Nut 8 2 05700-003-58-03 Vacuum Breaker Mounting Bracket 9 4 04730-011-61-47 Vacuum Breaker Fitting 10 2 04730-002-18-54 Fitting 11 2 05330-011-74-55 O-Ring 12 1 093
SECTION 6: PARTS SECTION WASH SYSTEM 1 4 2 3 WASH AND FILL SYSTEM 6 5 7 10, 11 12 2 9 8 LOCATED INSIDE TANK 30 13 29 28 14 15 27 16 25, 26 24 17 23 22 31 21 COLD WATER 20 HOT WATER 18 07610-003-61-11 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 37 19
SECTION 6: PARTS SECTION WASH SYSTEM Number QTY Part Number Description 1 1 05700-021-61-78 Wash Tank Strainer 2 2 05700-003-42-83 Wash Arm 3 4 05330-011-74-55 O-Ring, 13/16” OD 4 1 05330-003-41-73 Grommett 5 1 05700-003-49-32 Tube, Stainless Steel 6 1 05700-021-62-22 Wash Tank Overflow 7 1 05330-400-05-00 Wash Tank O-Ring 8 1 05311-011-62-65 Washer 9 1 04720-003-57-29 Hose, 3/4” OD 10 1 05700-003-59-21 Overflow Support 11 2 05310-373-01-00 10-24 Locknut 12 1
SECTION 6: PARTS SECTION CONVEYOR AND DRIVE SYSTEM 1 05700-005-49-10 CONVEYOR AND DRIVE SYSTEM 2 09330-003-45-66 5 05700-003-48-99 3 6 09330-003-58-52 09330-003-51-17 4 05700-003-59-93 19 7 09330-003-58-32 05700-003-58-54 8 05330-003-41-75 05340-003-41-83 9 18 16, 17 15 05700-003-58-50 05305-171-10-00 05930-303-38-00 05975-011-63-56 14 05930-011-61-65 10 05700-003-48-87 13 05975-011-63-56 11 06105-003-44-23 12 05700-003-48-57 07610-003-61-13 Delta 1200 Technical Manual 0761
SECTION 6: PARTS SECTION CONVEYOR AND DRIVE SYSTEM Number QTY Part Number Description 1 1 05700-003-49-10 Cylinder 2 1 09330-003-45-66 Rack 3 3 09330-003-51-17 Guide Block 4 1 05700-003-59-93 Strainer Weldment 5 1 05700-003-48-99 Drain Defelctor, Wash 6 1 09330-003-58-52 Plate, Skid 7 1 09330-003-58-32 Drive Gear 8 1 05330-003-41-75 Washer 05340-003-41-83 Extension Spring 9 10 1 05700-003-48-87 Gear Motor Box 11 1 06105-003-44-23 Gear Motor 12 1 05700-003-48-5
SECTION 6: PARTS SECTION DOOR ASSEMBLY 1 09905-021-64-88 2 05340-001-96-30 3 07610-003-61-30 4 09905-011-61-70 5 05340-021-62-04 6 05305-173-03-00 Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 41
SECTION 6: PARTS SECTION DOOR ASSEMBLY Number QTY Part Number Description 1 1 09905-021-64-88 Schematic Decal 2 1 05340-001-96-30 Door Hasp 3 1 07610-003-61-30 Complete Door Assembly 4 1 09905-011-61-70 ON/OFF Decal 5 2 05340-021-62-04 Hinge 6 6 05305-173-03-00 Screw Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised:05-21-2012 42
SECTION 7: ELECTRICAL SCHEMATICS 43
SECTION 7: ELECTRICAL SCHEMATICS Delta 1200 Technical Manual 07610-003-62-15 G Issued: 10-27-2008 Revised: 05-21-2012 44
