User Manual

Register Today to Protect Your Product
Problem or Damaged Package? DO NOT RETURN TO STORE
www.TouchlessTrashcan.com/register
EZF003C ® Contact us on www.iTouchless.com/contacts/ or call toll free 1-650-578-0578 for instruction.
QUICK INSTALLATION GUIDE:
OPERATING INSTRUCTIONS:
.
®
EZ FAUCET
TOUCH FREE ADAPTOR
®
USER MANUAL
EZF003C
1. Remove existing faucet aerator by turning counter-clockwise. Use the “Hexnut” Wrench,
pliers, or vice grips if it is tight (Fig. A).
2. After aerator is removed, ensure that the rubber washer from existing aerator is
removed. If the washer is not in the lip of the existing aerator, it should be inside the
water exit of the existing faucet.
3. Before installing the EZ Faucet, check if your faucet exit has Inside Thread (male
adaptor) or Outside Thread (female adaptor) type. Male adaptor type: Insert the Rubber
Washer that comes with package into the Adaptor (FIG. C1). Female adaptor type: Do not
use any rubber washer (FIG. C2).
4. Install EZ Faucet by turning the EZ Faucet Adaptor clockwise to attach to the faucet (first
use fingers to tighten, then use included “Hexnut” Wrench (FIG. D) for a final snug fit).
5. Remove EZ Faucet battery cover (see No.2 in Changing Battery section) and insert 4
new AAA Batteries (make sure batteries are inserted in the correct directions (+ and -)
as indicated in the battery holder). Close the battery door firmly (FIG. B).
6. Press and hold the Reset Button down for 3 seconds to adjust the sensor range
automatically. EZ Faucet is ready for use after turning the faucet handles to ON position
(adjust and check the water temperature properly before use – see Setting Water
Temperature and Flow Rate section) (FIG. E).
If you encounter problems during installation, please call 1.650.578.0578 or visit our
website at http://www.ezfaucet.com.
Program the Sensor Range / Reset the EZ Faucet: (FIG. E)
1. Turn the Faucet handles to OFF position.
2. Press and hold the Reset Button for 3 seconds until the green light flashes
and then release the button.
3. Wait Until the green flashing light stops. Sensor range/EZ Faucet is set and ready
for use after turning the faucet handles to ON position (adjust and check the water
temperature properly before use – see Setting Water Temperature and Flow Rate
section.
Note : If the sensor is too sensitive, try putting your hand 3”
~
5” below the sensor
while programming the sensor range. This will shorten the sensor range.
Setting Water Temperature and Flow Rate:
1. Turn faucet handles to COLD position.
2. Press Manual Override Button once (FIG. E).
3. While the water is running, move existing faucet handles to adjust water
temperature and flow rate.
4. After water temperature and flow rate is set, press Manual Override to turn off
the water. Automatic feature is resumed.
Low Battery Indicator:
It is optimal to use 4 Alkaline batteries with the same brand. They will last longer and keep your
EZ Faucet at best performance. Approximately 1 to 2 weeks before the batteries drain
completely, the orange POWER LOW indicator will begin to flash. Change all batteries as soon as
possible. (see Changing Battery section).
Changing the Batteries:
1. Turn the faucet handle to OFF position.
2. Remove the battery holder by pulling the battery holder out of the compartment.
3. Take the 4 batteries out one-by-one and replace with new batteries (make sure to put
batteries in correct directions).
4. Close battery holder by pushing the battery holder into the compartment until it is firm.
Then adjust the sensor range (see Program the Sensor Range section).
Problem or Damaged Package? DO NOT RETURN TO STORE
Contact us on www.iTouchless.com/contacts/ or
call 1-650-578-0578 for instructions.