Users Manual

ManualsBrandsIntelliFire ManualsSmart HomeFT-RC400 IntelliFire Touch Remote Control

Hearth & Home Technologies • IFT-RC400U User Manual • 2564-983 • 10/20

User Manual

IFT-RC400

IFT-RC400 IntelliFire Touch Remote Control

Model: 2564-110

INDICATOR BAR

SCREENSCREEN

Turn Flame On/O󰀨

Toggle this function to turn ON or OFF your appliance.

Thermostat

Introduction

This user manual serves as a quick reference to the

screen, functions and indicators on your IntelliFire Touch

Remote control.

FUNCTIONSFUNCTIONS

SELECTION

INDEX

ROOM TEMPERATURE

DISPLAY

You can set and maintain your desired room temperature

with the thermostat function. This function automatically

adjusts your appliance to maintain the desired set

temperature (ST).

To achieve the most accurate thermostat function, place

your remote control in the same general space that

you want to have the temperature controlled by your

appliance. For best results, keep your remote

control away from direct radiant heat from the appliance,

adjacent windows and doors, HVAC vents, and direct

sunlight.

To use the thermostat function, access the main menu

screen on your remote, and select thermostat. Next,

select your desired set temperature and press SET to

conrm the setting. The actual room temperature (RT),

measured by your remote control, will be displayed in

the upper right corner of the main menu screen. To turn

the thermostat function o󰀨, select thermostat on the main

menu screen and select OFF in the bottom left corner of

the temperature setting screen.

OFF

The thermostat function will automatically adjust the ame

height based on the di󰀨erence between the RT and the

ST. As the RT rises closer to the ST, the ame height will

automatically adjust down.

During thermostat use, you will not be able to set your

desired ame height level. Your appliance will

automatically adjust ame height based on the di󰀨erence

between the RT and ST.

Summary of content (9 pages)

PAGE 1
IFT-RC400 IFT-RC400 IntelliFire Touch Remote Control Model: 2564-110 User Manual Introduction Thermostat This user manual serves as a quick reference to the screen, functions and indicators on your IntelliFire Touch Remote control. You can set and maintain your desired room temperature with the thermostat function. This function automatically adjusts your appliance to maintain the desired set temperature (ST).
PAGE 2
FUNCTIONS Thermostat with Heat Management If your appliance is using any of the HM1-HM4 ports on the IFT-PACM the remote control will adjust the flame height and blower settings to better maintain a consistent heating value. RGB Lights If your appliance is equipped with the RGB lights, you can use this function to adjust the desired intensity when appliance is on or off. You will also be able to select one of the seven colors or select a scrolling color spectrum of the seven colors.
PAGE 3
FUNCTIONS INDICATORS Fan Speed* Temperature Display If your appliance is equipped with the fan feature, use this function to increase or decrease the amount of heat released into your room. A built-in delay timer will turn the fan on three minutes after your appliance has been running to prevent cool air from being pushed into the room. If the flame is turned off with the fan ON, the fan will continue to run for 12 minutes then shutdown as long as the flame stays off.
PAGE 4
INDICATORS Backup Battery The battery life indicator is for a backup power source for the IFT-ECM located inside your appliance. It is intended to operate the appliance in the event of a power failure. Consult your owner’s manual for your appliance on how to utilize this feature. Batteries should only be used as an appliance power source in the event of a power outage. Batteries should not be used as a primary long-term power source. Note: Battery backup is not available if a Power Vent is installed.
PAGE 5
INDICATORS Replace Remote Batteries OR Must Replace Remote Batteries to Operate Appliance Maintenance Your appliance will remind you to schedule routine service after 300 hours of Flame ON time is accumulated. Please contact your dealer for a 300 hour inspection to ensure your appliance is operating at peak performance. To reset the 300-hour maintenance reminder when the RC400 displays the following message: Your remote batteries are low.
PAGE 6
Frequently Asked Questions/Troubleshooting Symptom Possible Cause The appliance does not respond to commands from the IFT-RC400 or display does not light up when screen is touched. The display on IFT-RC400 lights up when screen is touched but it does not respond to commands. The IFT-RC400 displays the following message on-screen: No dealer info available The IFT-RC400 displays the following message on-screen: Call “Dealer Name & Number” to schedule maintenance. Batteries are depleted.
PAGE 7
Frequently Asked Questions/Troubleshooting (continued) Symptom Possible Cause The IFT -RC400 displays the following message on-screen: Appliance safely disabled. Call dealer for service. In addition the LED indicator on the IFT-ECM will flash twice red and once green indefinitely. The IFT-RC400 does not pair or unpair from the IFT-ECM. The IFT-RC400 displays the following message on-screen: “Remote Control Communication Error.” The IFT-ACM does not respond to commands from the IFT-RC400.
PAGE 8
Frequently Asked Questions/Troubleshooting (continued) Symptom Possible Cause The flame height setting on the IFT-RC400 does not appear to be functioning properly. Stepper motor is not connected. Check if the 4 pin wiring harness from the stepper motor is connected to the IFT-ECM. Ember/backlighting malfunction. Using an RMS voltage meter, check the voltage coming out of the lights port on the IFT-ACM when the lights are set to highest level on the IFT-RC400.
PAGE 9
Regulatory Certification Canada The IFT-RC400 wireless wall switch is certified for operation in the following countries: The IFT-RC400 is certified for use in Canada under Industry Canada (IC) Radio Standards Specification (RSS). • United States • Canada • Australia/New Zealand United States The IFT-RC400 complies with all applicable FCC equipment authorization, regulations, requirements, and equipment functions.