Operating Guide

9
8
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
2
Unpack dispenser components.
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
Feed tubes down the hole in
the sink or countertop until the
base is at rest on the sink or
countertop surface.
From under the sink, place the
rubber washer, plastic spacer and
semi-circular mounting plate onto
the threaded stud.
Place long nut onto the threaded
stud. Make sure faucet head is
at the desired angle. Tighten the
long nut until snug, while ensuring
the semi-circular mounting plate
extends beyond the sink hole.
Do not over tighten long nut. May cause
damage to faucet.
For sinks thicker than 1" the plastic spacer
is not required
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
Hot100/Hot150
Hot100/Hot150
Hot100/Hot150
INSTALLING THE FAUCET
-
Hot100/Hot150
b
a
C
NOTICE
To see a tutorial of this installation:
http://goo.gl/AZOHu
Select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
The tank should be within 16" or less
of faucet water lines and within 30"
or less of a standard grounded outlet.
While holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Property Damage: Tank must be located
within 16" of faucet and within 30" or less
of a standard grounded outlet. DO NOT extend
plumbing or electrical lines.
3
Without depressing the gray button,
place the snap-connect fitting at
the end of the blue 1/4" tube onto
the left fitting on the tank, pushing
until it clicks into place. (1)
Slip the flexible white 7/16" tube
over barbed middle fitting and slide
down approximately 1/2". (2)
Slip the clear 5/16" tube over the
far right smooth fitting and slide
down approximately 1/2". (3)
Visually check for pinched or
crimped tubes.
4
Property Damage: Pinched or blocked water
lines may cause damage to the dispenser tank.
Check to make sure tubes are connected
properly and are pushed down as far as possible.
Tank must be
mounted level
to ensure
proper operation.
Hose clamps are not needed for any
of the connections.
Mount tank vertically in an area that
allows clearance on the underside of
the tank for drainage, if necessary.
DO NOT over tighten screws.
Pre-drill 1/8" pilot holes at marks.
Turn screws into pre-drilled holes,
leaving 1/4" exposed.
Hang the tank on the screws.
Tighten the screws with only 1/2
turn clockwise.
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
Leave 1/4" for
hanging tank.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
(1) (2) (3)
MOUNTING THE TANK
CONNECTING FAUCET TO TANK
a
a
b
NOTICE
NOTICE
To see a tutorial of this installation:
http://goo.gl/AZOHu