9YPSN 645(OW) GH R/HA 9YPSN 645(AN) GH R/HA EN English Operating Instructions HOB Operating Instructions,1 Warnings,2 Assistance,2 Description of the appliance,3 Installation,4 Start-up and use,8 Precautions and tips,8 Maintenance and care,9 Troubleshooting,9 Contents
EN EN Warnings Assistance WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.
EN Description of the appliance Overall view 1. 2. 3. 4. 5. Support Grid for COOKWARE GAS BURNERS Control Knobs for GAS BURNERS Ignition for GAS BURNERS SAFETY DEVICES • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. • Control Knobs for GAS BURNERS adjust the size of the flame. • GAS BURNER IGNITION enables a specific burner to be lit automatically. • SAFETY DEVICE stops the gas flow if the flame is accidentally extinguished.
Positioning ! Keep packaging material out of the reach of children. It can become a choking or suffocation hazard (see Precautions and tips). ! The appliance must be installed by a qualified professional according to the instructions provided. Incorrect installation may cause harm to people and animals or may damage property. ! This unit may be installed and used only in permanently ventilated rooms in accordance with current national regulations.
Ventilation To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams). 560 mm . 45 m m. Where a hob is installed above an oven without a forced ventilation cooling system, adequate ventilation must be provided inside the cabinet by means of air holes through which air can pass (see figure).
EN • Setting the burners to minimum 1. Turn the tap to the low flame position. 2. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. 3. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. 4. Some appliances have a safety device (thermocouple) fitted.
Burner and nozzle specifications EN Table 1 Liquid Gas Burner Diameter (mm) Thermal Power kW (p.c.s.*) Nomin. Reduc. By-pass Nozzle 1/100 1/100 (mm) (mm) Natural Gas Flow* g/h *** ** Nozzle 1/100 (mm) Flow* l/h Rapid (R) 100 3.00 0.70 39 86 218 214 132(H3) 286 Semi Rapid (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 Auxiliary (A) 55 1.00 0.
EN Start-up and use ! The position of the corresponding gas burner or electric hotplate* is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: ● Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. Respecting and conserving the environment ! This procedure must be performed by a qualified technician authorised by the manufacturer. • Cook your food in closed pots or pans with well-fitting lids and use as little water as possible. Cooking with the lid off will greatly increase energy consumption. • Use purely flat pots and pans.
400011246167 03/2018 - XEROX FABRIANO EN 10