NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier TECH ROD GYM TR-2 Assembly Instruction Parts List Warranty Ordering Parts Model TR-2 Retain This Manual for Reference 09-14-04 V4 OWNER'S MANUAL IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
WARNING LABELS PLACEMENT The Warning Labels shown here have been placed on Lower Pulley Support Base. If this Labels are missing or illegible, please call Customer Service at 1-800-9998899 for free replacement. Apply the Label in the location shown.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM.........................................................................……….
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE PACK 3
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Base Platform (#8) on flat surface. Attach the Vertical Frame (#1) to the open bracket on the Base Platform. Secure it with five M10 x 5/8” Allen Bolts (#9) and ؾ” Washers (#10). DO NOT tighten the Bolts yet. B.
STEP 2 (See Diagram 2) A.) Attach the lower Rear Support Frame (#2) to the Base Platform (#8). Secure it with one M10 x 4 7/8” Hex Bolt (#13), Ø ¾” Washer (#10), and M10 Aircraft Nut (#16). DO NOT tighten the Nut and Bolt yet. B.) Insert bottom of Lower Pulley Support Base (#45) into the openings on the Base Platform. Secure it with one M6 x 1¾” Hex Bolt (#14) and M6 Aircraft Nut (#15) to each opening.
STEP 3 (See Diagram 3) A.) Attach the High Pulley Support Bar (#18) to the Upper Frame (#17). Securely tighten with one Bracket (#19), two M10 x 2 3/8” Hex Bolts (#20) and two ؾ” Washers (#10). Cover the two Hex Bolts with two M10 Nut Caps (#21). B.) Attach the Upper Frame (#17) to the Vertical Frame (#1). Securely tighten with five M10 x 5/8” Allen Bolts (#9) and ؾ” Washers (#10). C.) Attach two Lat Bar Holders (#39) to the side of the Vertical Frame (#1).
STEP 4 (See Diagram 4) A.) Attach the Tech Rod Set (#24) to the Rear Support Frame (#2). Secure it with four Ø 1/4” x ¾” Philips Screws (#25). B.) Slide the Tech Rod Organizer (#23) onto the top of the Rods to hold each Rod in position.
STEP 5 (See Diagram 5) A.) Place the Seat Pad (#27) onto the Seat Support (#26). Secure it with four M6 x ¾” Hex Bolts (#6) and ؽ” Washers (#7). B.) Attach the Seat Support (#26) to the open bracket on the Vertical Frame (#1). Use a Lock Knob (#28) to securely lock the Seat Support in position.
STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#30) to the front of Seat Support (#26). Secure it with one M10 x 3” Hex Bolt (#12), two ؾ” Washers (#10), and one M10 Aircraft Nut (#16). B.) Cover the Nut and Bolt with two M10 Nut Caps (#21). Cover the Nuts on the Cable Roller (#44) with two M8 Nut Caps (#29).
STEP 7 (See Diagram 7) A.) Insert a Foam Tube (#32) halfway through the hole on the Seat Support (#26). Insert a Foam Tube halfway through the hole on the Leg Developer (#30). B.) Push four Foam Rolls (#33) onto the Foam Tubes from both ends. Plug four Foam Roll End Caps (#34) into the ends of the Tubes.
STEP 8 (See Diagram 8 & Lat Bar Cable Loop Diagram) A.) Follow the below instructions to use the Lat Bar. B.) Attach a Tech Rod Cable (#11) to the Right Pulley on the Extension Tube (#43). Attach the other end, L Shaped Connector (#41) to one of the Tech Rod. C.) Attach one 57” Lat Cable (#35) to the right Pulley on the Upper Pulley Support Bar (#18). Draw the Cable over the Pulley then downward to the right Pulley on the Extension Tube (#43).
LAT BAR CABLE LOOP DIAGRAM 12
STEP 9 (See Diagram 9 & Leg Developer Cable Loop Diagram) A.) Follow the below instructions to use the Leg Developer. B.) Detach the end of the Lat Bar Cables from the End Hooks on Tech Rod Cables and hook the Cable ends onto the Cable Hangers on the side of the Vertical Frame. C.) Store the Lat Bar onto the Lat Bar Holders (#39) on the side of the Vertical Frame. D.) Connect the end of the 40” Leg Developer Cables (#36) from Cable Hangers to the Tech Rod Cables (#11).
LEG DEVELOPER CABLE LOOP DIAGRAM 14
STEP 10 (See Diagram10 & Cable Loop Diagram) A.) Follow the below instructions when doing bench press or butterfly exercises. B.) Attach the ends of Lat Bar Cables (#35) and Leg Developer Cables (#36) onto the Cable Hangers (#42) on the side of the Vertical Frame. C.) Connect the two Hand Straps (#38) to the Tech Rod Cables (#11) for various exercises. Please refer to the Exercise Chart.
TECH ROD CABLE LOOP DIAGRAM 16
EXPLODED DIAGRAM 17
TECH ROD RESISTANCE CHART TECH ROD (each side) 5LB 10LB 10LB 25LB 50LB Bench Press/ Butterfly 5 LB 10 LB 10 LB 25 LB 50 LB LAT CABLE 5 LB 10 LB 10 LB 25 LB 50 LB LEG DEVELOPER CABLE 3 LB 8 LB 8 LB 20 LB 35 LB TOTAL 100LB 100LB 74LB *Numbers are approximate. Actual resistance may vary. *Value is for each cable.
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
