Installation Guide

ManualsBrandsIDEAL Security ManualsTools & HardwareSatin Nickel Coated Zinc Storm and Screen Pull Handle with Key Lock Set

5/16"

6 PLCS

1 3/4" 1 3/4"

5 1/8"

27/32"

1 5/32"

29/32"

1/16"

8 PLCS

LSDXCR2267 (LATCH SET DX CR3 2260 357)

TEMPLATE AND INSTALLATION INSTRUCTIONS

WARNING

: CHECK DOOR PROFILE PRIOR TO INSTALLATION

You will require a profile wide enough for proper installation.

With the door closed, the minimum inside door profile width is 1-3/4” from the edge of the door frame (glass side) to

the edge of the door jamb or metal door frame (z-bar), which ever is narrower.

The minimum outside door profile width is 2-1/8” from the edge of the door frame (glass side) to

the edge of the door jamb or metal door frame Z-bar), which ever is narrower.

DETERMINE IF YOUR STORM DOOR IS HINGED RIGHT OR LEFT FOR PROPER USE OF DRILLING TEMPLATE

From outside of door, looking in, if the hinges are on your left, your door is left handed.

If the hinges are on the right, it is a right handed door.

Ensure that the inside latch and deabolt do not interfere with the prime door lock.

cutting linecutting line

RFQDXCR3

PAGE 1 OF 5

Summary of content (5 pages)

PAGE 1
LSDXCR2267 (LATCH SET DX CR3 2260 357) TEMPLATE AND INSTALLATION INSTRUCTIONS RFQDXCR3 WARNING: CHECK DOOR PROFILE PRIOR TO INSTALLATION You will require a profile wide enough for proper installation. With the door closed, the minimum inside door profile width is 1-3/4” from the edge of the door frame (glass side) to the edge of the door jamb or metal door frame (z-bar), which ever is narrower.
PAGE 2
TEMPLATE PLACEMENT AND DRILLING INSTRUCTION 1. Fold the template on the dotted line to 90 according to the handedness (left or right). JAMB DOOR 2. With the door in closed position, place folded template on inside of door so that the SIDE A is against the jamb or metal z-bar, which ever projects out farther; and SIDE B is on the inside surface of door. 3. Use a center punch to mark the position of 6 holes on the inside surface of door on SIDE B.
PAGE 3
LSDXCR2267 HANDLE SPINDLE AND LATCH SCREW SELECTION INSTRUCTION 1. Print out this sheet using 1:1 scale. (verify using a ruler against the print out image below) 2. Measure door thickness. 3. Over lay spindles and screws on top of the image below. 4. Select the spindle and screws that match your door thickness. DOOR THICKNESS SCREW SPINDLE 1" TO 1 1/8" 1 1/4" TO 1 3/8" 1 1/2" TO 1 5/8" 1 3/4" TO 1 7/8" 2" TO 2 1/4" Now that the handle spindle and latch screws are selected and ready for installation.
PAGE 4
LSDXCR2267 KEYLOCK SPINDLE AND DEADBOLT SCREW SELECTION INSTRUCTION KEY LOCK SPINDLE PREPARATION 1. Print this sheet using 1:1 scale. 2. Over lay flat spindle against the image. 3. Mark door thickness on the spindle. 4. Cut off at the mark line. Now the key lock spindle is ready for installation. PLACE SPINDLE HERE DEADBOLT SCREW SELECTION DOOR THICKNESS 1" TO 1 1/8" 1 1/4" TO 1 3/8" 1 1/2" TO 1 5/8" 1. Print out this sheet using 1:1 scale. 2. Over lay screws on top of the image. 3.
PAGE 5
HANDLE AND LATCH INSTALLATION 1. Arrange handle, housing, and backplate as shown. 2. Place spindle & spring in between housing & backplate. 3. Place the outside handle assembly (from step 1&2) on door. (If your door thickness is not standard then: The spindle should project through inside of door a max of 3/8" and min of 1/4". You may have to cut off spindle.) 4. Place the latch on inside of door, fasten with two machine screws. Do not over tighten screws. Fasten the backplate with the tie down screw. 5.