Version: 3.30 Doc.
FCC Statement This equipment has been strictly tested and reached to Class A, pursuant to part 15 of the FCC rules, which focus on providing reasonable protection against harmful exterior interference when the equipment is operated in a commercial environment. While the equipment running, it maybe cause a strong electromagnetic wave with constant frequency, which may interrupt the radio communication if the user does not installed and used in accordance with the product user manual.
Table of Content Table of Content About This Guide ...............................................................................................................4 Important Safeguards and Warning ................................................................................5 Chapter 1 Product Introduction .......................................................................................6 1-1. Product Package Content ....................................................................................
About This Guide About This Guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols to use throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you must follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
Important Safeguards and Warning Important Safeguards and Warning It is not recommended to install this product by unqualified person. The method and material of installation should be insured for the weight of the product and enclosure as pan/tilt, camera lens, and so on Stop using and power off the product if any unusual smell or smoke comes from the camera. Do not install the camera in an intermittent lighting environment.
Chapter 1: Product Introduction Chapter 1 Product Introduction Characterized as fast speed, high decision, low noise and long life, High-speed dome is being popular more and more, it has being the best choice of retail, business, industry, government and entertainment field depending on its good construction, convenient installation and widen range of surveillance. 1-1. Product Package Content Please check the package content by the following list.
Chapter 1: Product Introduction 1-2. Product Overview Parts Name Description A. Screw holes for speed dome camera bracket B. Speed dome power and RS485 connecting wires Blue color: RS485 + (Rx +) Yellow color: RS485 – (Rx -) Black color: Revise Red color: Revise The Blue color wire RS485 + (Rx +) & Yellow color wire RS485 – (Rx -) for Speed dome controller. C. BNC video output connector D. Surge protection cable (Yellow Color): Connect to the ground for surge protection function. E.
Chapter 2: Installation 1-3. Product Features Optical Zoom: 36X (f = 3.4mm~122.4mm) optical zoom. Day & Night: Switches from color mode to B/W mode automatically. Weatherproof: IP66 and build in fan /heater for all weatherproof environmental structure. Illumination: Super sensitivity of 0.05 lx (color mode) / 0.0015 lx (B/W mode). Resolution: 540-TV line at color imaging horizontal resolution. Masking: 24 Privacy zone masking enables users to veil unwanted zones.
Chapter 2: Installation Chapter 2 Installation 2-1. Specification Item/Model Image Sensor FDMO-36X FDMO-35X FDMO-22X 1/3“ SONY EXview 1/4" SONY Ex-view CCD HAD CCD II (Effio-E) Optical Lens 36x (f= 3.4~122.4mm) 530 TV lines Minimum None 650 TV lines 650 TV lines 1.0 Vp-p /75Ω (Composite) Video Output S/N 22x (f=3.9~85.8mm) 16x Digital Zoom Resolution 35x (f= 3.6~126mm) 52 dB (AGC Off) 52 dB (AGC Off) 52 dB (AGC Off) 1.4 Lux. (F1.6; IRE50) 0.5 Lux. (F1.6, Color) 0.03Lux (F1.
Chapter 2: Installation S/W: 256; DIP Switch: 64 ID address RS-485; Half-Simplex Interface Baud Rate 1200 / 2400 / 4800 / 9600 BPS (Selectable) Protocol Pelco P and Pelco D auto detection Housing Aluminum Wall / Ceiling (Optional) Mount Type IP 66 / Build in Fan & Heater Weatherproof 6 inches Dimension DC12V/3A Environmental -35℃~50℃ Dimension 5 Kg Weight 2-2.
Chapter 2: Installation 2-3. Baud Rate Setup There is an 8-pins switch (Red one) on PCB as showing below: ON 1 2 3 4 5 6 7 8 Baud Rate (Pin 7 and 8 are the selectors for baud rate) Pin 7 Pin 8 1200/bps OFF OFF 2400/bps ON OFF 4800/bps OFF ON 9600/bps ON ON 2-4.
Chapter 2: Installation 11 OFF OFF ON ON OFF OFF 12 ON OFF ON ON OFF OFF 13 OFF ON ON ON OFF OFF 14 ON ON ON ON 15 OFF OFF OFF OFF OFF ON OFF OFF 16 ON OFF ON OFF OFF OFF ON OFF 17 OFF OFF ON OFF 18 ON ON OFF OFF OFF OFF OFF OFF ON ON 19 ON OFF 20 ON OFF ON OFF ON OFF 21 OFF ON ON OFF ON OFF 22 ON ON ON OFF ON OFF 23 OFF OFF OFF ON ON OFF 24 ON OFF OFF ON ON OFF 25 OFF ON OFF ON ON OFF 26 ON ON OFF ON O
Chapter 2: Installation 44 ON OFF ON ON OFF ON 45 OFF ON ON ON ON OFF ON OFF OFF ON 47 ON OFF ON ON OFF 46 OFF ON ON 48 ON OFF OFF OFF ON ON 49 OFF ON OFF OFF ON ON OFF 50 ON OFF ON ON 51 ON OFF OFF ON OFF ON ON 52 ON OFF ON OFF ON ON 53 OFF ON ON OFF ON ON 54 ON OFF ON OFF ON OFF OFF ON ON 55 ON ON ON 56 ON OFF OFF ON ON ON 57 OFF ON OFF ON ON ON 58 ON OFF ON OFF OFF ON ON ON 59 ON ON ON ON 60 ON OFF ON
Chapter 2: Installation 2-5. Product with Ceiling Mount Installation 2-5-1. Ceiling Mount Model: BCO-27L BCO-27L Dimension Installation Procedure: Please follow the steps below to install the BCO-27L and speed dome. Step 1: Tear off the anti-shake tap and cover from the camera lens. Step 2: Remove the camera cover inner protection stuff, and install the camera cover with the speed dome by tightening up the screws.
Chapter 3: Operation 2-6-1. Wall Mount Model: BWO-27S 2-6-2.1 BWO-27S Dimension 2-6-2.2 Installation Procedure: Please follow the steps below to install the BWO-27S and speed dome. Step 1: Tear off the anti-shake tap and cover from the camera lens. Step 2: Remove the camera cover inner protection stuff, and install the camera cover with the speed dome by tightening up the screws. Step 3: Organize the required cables from the ceiling through the cables to the BWO-27S pipe.
Chapter 3: Operation Chapter 3 Operation 3-1. General Operation 3-1-1. Camera Basic Control Function FastCam III offer basic function control by enter numbers on keyboard, for easy and fast command. Function Description Enter/Exit On Screen Press [Menu] button, “95 + [Preset] button” to enter OSD menu. Menu Press [Menu] button again to exit the OSD menu. Start Auto Scan Press [Scan] button or “99 + [Call] button”. Start Auto Pattern Press [Pattern] button or “100 + [Call] button”.
Chapter 3: Operation Select Auto/Manual in the menu. (Refer to Menu Edit Manual) Focus Far Under the Manual mode, please press [FAR] button till the view is clearly. The manual control will be invalid under the Auto mode. Select Auto/Manual in the menu. (Refer to Menu Edit Manual). Focus Near Under the Manual mode, please press [FAR] button till the view is clearly. The manual control will be invalid under the Auto mode.
Chapter 3: Operation 3-1-2. OSD Display when power on When power on, the protocol and address will be displayed on the screen. After the dome accepts the correct commands, the information will disappear. E.g. : The screen displays as following information. The information is as the protocol, Firmware version, ID Address and Baud rate which have been setup. Please refer to the right side window screen. SYSTEM INFO FASTCAM III VERSION:3.30 BAUD RATE:9600 BPS PROTOCOL:PELCO-D/P 3-2.
Chapter 3: Operation 3-2-2. Menu Function Description [MAIN MENU] Via the controller, Setup Preset 95 or Press [MENU] button to enter the main menu. The main menu is including System setup, Display setup, Parameter setup, Recover setup, others setup, Execution menu and Exit. SETUP MENU The initialization of speed dome can be read in System version, →SYSTEM SETUP Baud Rate, Camera brand, Protocol, Hardware or Software DISPLAY SETUP Address.
Chapter 3: Operation S/W ADDRESS: a.) Select in main menu b.) Press [OPEN] button or lean to right direction of joystick to enter SYSTEM SETUP menu. c.) Move the joystick down to S/W ADDRESS and then press [OPEN] button or lean to right direction of joystick to enable the setup ID address by S/W ADDRESS. When the S/W ADDRESS function is enabled; the DIP ADDRESS will be disabling automatically. d.) Move the joystick up or down to select ID address from 0~255.
Chapter 3: Operation B. [DISPLAY SETUP] DISPLAY SETUP SETUP MENU SYSTEM SETUP CAMERA ID:ON/OFF DISPLAY SETUP PRESET:ON/OFF PARAMETER SETUP PAN/TILT ANGLE:ON/OFF RECOVERY SETUP TEMPERATURE:ON/OFF OTHERS SETUP CAMERA OSD:ON/OFF EXECUTION MENU BACK EXIT EXIT Set information by the user what to show on the screen when user does the correlative operation. ON: Display camera ID address on the screen. OFF: Disable the camera ID address from screen.
Chapter 3: Operation C. [PARAMETER SETUP] It is used to setup the functions and parameters of the dome. It includes 7 sub-menus: Motion Setup, Title Edit, Tour Edit, Scan Edit, Pattern Edit, Mask Edit, Power On etc.. PARAMETER SETUP SETUP MENU SYSTEM SETUP CAMERA SETUP DISPLAY SETUP MOTION SETUP PARAMETER SETUP TITLE EDIT RECOVERY SETUP TOUR EDIT OTHERS SETUP SCAN EDIT EXECUTION MENU PATTERN EDIT EXIT MASK EDIT POWER ON:SCAN BACK EXIT 1.
Chapter 3: Operation User may change settings of Camera AUTO: Camera will automatically adjust focus. MANUAL: User manually adjusts focus. ON: Enable digital zoom. OFF: Disable digital zoom. ON: Enable White Balance. OFF: Disable White Balance. < BLC: OFF/ON> ON: Enable Back Light Compensation. OFF: Disable Back Light Compensation. < DAY/NIGHT: AUTO/OFF> AUTO: Automatically switch day/night mode.
Chapter 3: Operation OFF: The image is never frozen. CAMERA SETUP 2/2 CAMERA SETUP CAMERA SETUP MIRROR: ON/OFF MOTION SETUP FLIP: ON/OFF TITLE EDIT LOW SHUTTER: ON/OFF TOUR EDIT AE MODE: IRIS/AE SCAN EDIT NR: ON/OFF PATTERN EDIT PRESET MODE: TRACE/NO TRACE MASK EDIT CAMERA MENU POWER ON:SCAN PRE PAGE BACK BACK EXIT EXIT < MIRROR: OFF/ON> ON: Enable video mirror reflection. OFF: Disable video mirror reflection.
Chapter 3: Operation ON: Enable NR (Noise Reduction) function. OFF: Disable NR (Noise Reduction) function. < PRESET MODE: TRACE/NO TRACE> * this function is optional. ON: Enable Auto Trace Object function OFF: Disable Auto Trace Object function. CAMERA SETUP page is only for Sony camera module, other modules may not be available.
Chapter 3: 2.
Chapter 3: Operation ON: Enable Proportion. OFF: Disable Proportion. When dome is running tour/scan mode, if joystick is operate once, the program will be hold and resume later on. But if joystick is operate more than once the program will be cenacle itself. ON: Enable Activation. OFF: Disable Activation. When FastCam III is in idol of amount of time (user can define how many minutes), the camera will return to home position. ON: Enable home position.
Chapter 3: Operation Dwell time is when dome running tour mode, how many seconds should dome stay at in between the stops. To set home position “Press 76 + [Preset] button”. When camera is in idol, user can define how many minutes will camera return to home position.
Chapter 3: Operation 3.
TITLE EDIT CAMERA SETUP CAMERA SETUP PRESET/CAM: CAMERA/PRE001~128 MOTION SETUP TITLE EDIT: TITLE EDIT BACK TOUR EDIT EXIT SCAN EDIT PATTERN EDIT DISPLAY: MASK EDIT CAM001 POWER ON:SCAN BACK EXIT To edit each label, select the label to edit, lean down joystick to . The Camera and Preset Position can be marked separately. For each label, max 16 characters can be edited, including the space.Chapter 3: Operation 4. TOUR EDIT CAMERA SETUP TOUR →01 CAMERA SETUP RELOAD SET UP PRESET MOTION SETUP TITLE EDIT 01 001 09 009 TOUR EDIT 02 002 10 010 SCAN EDIT 03 003 11 011 PATTERN EDIT 04 004 12 012 MASK EDIT 05 005 13 013 POWER ON:SCAN 06 006 14 014 BACK 07 007 15 015 EXIT 08 008 16 016 NEXT PREVIOUS CLEAR BACK EXIT User can program dome when running , each dome can program up to 128 presets.
Chapter 3: 5. Operation CAMERA SETUP CAMERA SETUP SCAN EDIT MOTION SETUP TITLE EDIT SCAN MODE: 360/A←B/A→B TOUR EDIT POSITION A: PRE001~128/NO SCAN EDIT USE PATTERN EDIT MASK EDIT POSITION B: PRE001~128/NO POWER ON:SCAN USE BACK EXIT BACK EXIT User can program dome when running , each dome 3 different scan modes.
Chapter 3: 6. Operation CAMERA SETUP CAMERA SETUP MOTION SETUP TITLE EDIT TOUR EDIT PATTERN EDIT → RECODE SCAN EDIT RUN PATTERN EDIT BACK MASK EDIT EXIT POWER ON:SCAN BACK EXIT A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function.
Chapter 3: 7. Operation CAMERA SETUP CAMERA SETUP MOTION SETUP MASK EDIT TITLE EDIT TOUR EDIT SCAN EDIT PATTERN EDIT MASK EDIT 1. POWER ON:SCAN 2. BACK ZONE: 001~024 EDIT: DISPLAY: ON/OFF BACK EXIT EXIT Mask edit allows a user to program up to 24, user-defined areas that cannot be viewed by the operator of the dome system. A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide.
Chapter 3: 8. Operation CAMERA SETUP CAMERA SETUP POWER MOTION SETUP TITLE EDIT TOUR EDIT SCAN EDIT PATTERN EDIT POWER ON PRE01/08 SCAN TOUR01/08 PATTERN MASK EDIT POWER ON:SCAN BACK EXIT When dome is power on, user can program which dome will start up from. POWER ON Dome will just power on, remain position. PRE01~08 Dome will power on at which preset position.
Chapter 3: D. Operation SETUP MENU RECOVERY SETUP SYSTEM SETUP DELETE PRESETS OK DISPLAY SETUP DEFAULT SETTING PARAMETER SETUP RESET CAMERA RECOVERY SETUP REBOOT DOME OTHERS SETUP BACK EXECUTION MENU EXIT EXIT DELETE PRESETS Delete all the presets DEFAULT SETTINGS Restore all settings to default of Speed Dome. RESET CAMERA Use this function to reset all settings of camera module to factory default.
Chapter 3: E. Operation OTHERS SETUP MENU SYSTEM SETUP ALARM SET DISPLAY SETUP PASSWORD SETUP PARAMETER SETUP TV SYSTEM: RECOVERY SETUP TEMPERATURE: AUTO/MANUAL OTHERS SETUP CAMERA BRAND:AUTO EXECUTION MENU BACK EXIT EXIT NTSC/PAL 1. ALARM SETUP OTHERS ALARM SETUP →ALARM1 TYPE:N.O./N.C. PASSWORD SETUP ALARM2 TYPE:N.O./N.C. TV SYSTEM: NTSC ALARM3 TYPE:N.O./N.C. TEMPERATURE: AUTO ALARM4 TYPE:N.O./N.C.
Chapter 3: Operation FastCam III has four alarm inputs, which can be programmed as N.C. or N.O. When an alarm signal is received, it can triggers the user-defined action ALARM ACT (revise, pre001~128) and ALARM OUTPUT can be define as DISABLE, CONTINUE, 60 SECONDs. Disable When alarms triggers, no action will be responds.
Chapter 3: Operation access any of the Dome settings menus when the password setting is enabled. To set up password, move joystick to highlight PASSWORD press the number you wish to enter then press [CALL], example (1 + [CALL] as 1, 2+[CALL] as 2). six digitals. User may only enter Enter again in CONFIRM line to confirm, when it’s confirmed, OK will be shown. 3. Select the correct TV system for your area application. Otherwise the OSD display has problem sometime. 4.
Chapter 3: F.
Chapter 4: Problems Troubleshooting Possible Causes Remedies Power supply damaged or Replace insufficient power No action and images Wrong connection of power when power on supply Correct Faults in Remove engineering circuits Mechanical fault Repair Tilting camera Place uprightly Abnormal self-inspection.