Edger/Trimmer Operator's Manual
3
DO NOT MODIFY EDGER-TRIMMER
Unauthorized modication to the edger-trimmer may impair
its function and safety and aect edger-trimmer life.
TRAINING
1. Read the Operating and Maintenance In-
struction Manual carefully. Be thoroughly
familiar with the controls and proper use of
the equipment.
2. Never allow children to operate edger-trimmer.
3. Keep area of operation clear of all per-
sons, particularly small children and pets.
4. Thoroughly train anyone using the edger-
trimmer. Make sure all edger-trimer operators
know the safety, operating, and maintenance
procedures.
PREPARATION
1. Thouroughly inspect the area where edger-
trimmer is to be used, and remove all stones,
sticks, wire, bones, and other foreign objects
which might be picked up and thrown.
2. Do not operate edger-trimmer when barefoot
or wearing open sandals. Always wear sub-
stantial foot wear, and pants or slacks that cov-
er your legs when operating edger-trimmer.
3. Check fuel before starting engine. Do not ll
gasoline tank indoors, when engine is run-
ning, or while engine is still hot. Clean o any
spilled gasoline before starting engine.
4. Disengage cutterhead drive before starting
engine.
5. Do not use edger-trimmer unless blade guard,
belt guards, and debris guard are properly in
place.
6. Edge or trim only in daylight or in good articial
light.
7. Never operate equipment in wet grass. Always
be sure of
your footing. Keep a rm hold on
the handle and walk, never run.
OPERATION
1. Start the engine carefully. Keep hands and
feet well away from blade.
2. Do not change engine governor setting or
overspeed engine.
3. Wear safety glasses when operating edger-
trimmer.
4. Keep clear of discharge opening at all times.
Never direct discharge of any material toward
bystanders nor allow anyone near machine
while it is in operation.
5. Stop blade when crossing gravel drive, walks,
or roads.
6. After striking a foreign object, stop the engine
and inspect edger-trimmer for damage. Repair
damage before starting engine.
7. Avoid loss of control or tipping on slopes and
sharp corners by reducing speed.
8. If edger-trimmer should start to vibrate abnor-
mally, stop the engine and check for the cause.
Vibration is generally a warning of trouble.
9. Stop the engine whenever you leave the
edger-trimmer, and when making repairs or
inspections.
10. When repairing or inspecting, make certain
blade and all moving parts have stopped.
Disconnect spark plug wire and keep wire
away from plug to prevent accidental starting.
11. Do not run engine indoors.
12. Shut engine o and wait until blade comes to
a complete stop before removing grass that
may clog blade guard.
13. Watch out for trac when working near
roadways.
14. Stay alert for uneven sidewalks, holes in terrain,
or other hidden hazards when using edger-trim-
mer. Always push slowly over rough ground.
15. Remember, never operate edger-trimmer
unless blade guard, belt guards, and debris
guard are properly in place.
16. Disengage power to cutterhead and stop
engine before leaving edger-trimmer, before
making repairs, inspections or adjustments,
and when transporting or not in use.
MAINTENANCE AND STORAGE
1. Check blade mounting nut frequently for
proper tightness.
2. Keep all nuts, bolts, and screws tight to be
sure equipment is in safe working condition.
3. Never store edger-trimmer with
gasoline
in the tank in a building where fumes may
reach an open ame or spark. Be sure engine
has cooled before storing in any enclosure.
4. To reduce re hazard, keep engine free of
grass, leaves, or excessive grease.
5. After operating engine, never touch ex-
haust muer until it has cooled completely.
6. Keep edger-tirmmer in good operating
condition, and keep safety devices in place
.
GENERAL SAFETY SUGGESTIONS
Recommended by Outdoor Power Equipment Institute
Read Operator's Manual. Know location
and function of controls. Maintain safety
devices. Remove potential thrown objects.
Never edge or trim near people. Never carry
passengers. Look before backing. Avoid
slippery or steep areas. Stop blade and back
slowly if machine stops. Avoid blade unless
blade and engine are stopped.
CAUTION
TO AVOID INJURY