Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Vous pouvez utiliser de l’essence contenant jusqu’à 10 % d’éthanol (E10) avec cet appareil. L’utilisation d’essence contenant plus de 10 % d’éthanol annulera la garantie du produit. 532 44 71-59 Rev.
SAFETY RULES Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Look for this symbol to point out important safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.
• • • • • • • Never refuel the machine indoors. Never store the machine or fuel container where there is an open flame, spark or pilot light such as a water heater or on other appliances. Never fill containers inside a vehicle, on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling. Remove gas-powered equipment from the truck or trailer and refuel it on the ground.
ASSEMBLY Read these instructions and this manual in its entirety before you attempt to assemble or operate your new lawn mower. IMPORTANT: THIS LAWN MOWER IS SHIPPED WITHOUT OIL OR GASOLINE IN THE ENGINE. Your new lawn mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag.
OPERATION KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand their meaning.
OPERATION The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask over spectacles. 2. Rotate turnbuckle on drive control to increase drive speed. 3. Operate mower to test drive speed. Readjust as required. 4.
OPERATION 2. Remove grass catcher with clippings from under lawn mower handle. 3. Empty clippings from bag using both frame handle and bag handle. NOTE: Do not drag the bag when emptying; it will cause unnecessary wear. REAR DOOR GRASS BAG BRACKET GRASS CATCHER HANDLE GRASS CATCHER FRAME HANDLE GRASS CATCHER FRAME HOOK FIG. 7 BAG HANDLE REAR DISCHARGING (See Fig. 8) • Lift the rear door and install the clipping deflector (available accessory) legs into holes of handle brackets as shown.
OPERATION • CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season.
MAINTENANCE BEFORE EACH USE AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel syste
MAINTENANCE LAWN MOWER 6. Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise. • The recommended tightening torque is 35–40 ft. lbs. Always observe safety rules when performing any maintenance. IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVED BOLT SHOWN IN THE REPAIR PARTS SECTION OF THIS MANUAL. TIRES • • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
MAINTENANCE GRASS CATCHER • • 7. Continue adding small amounts of oil, rechecking the dipstick until oil level settles at FULL. DO NOT overfill, or engine will smoke heavily from the muffler on startup. 8. Always be sure to retighten oil dipstick before starting engine. 9. Reconnect spark plug wire to spark plug. The grass catcher may be hosed with water, but must be dry when used. Check your grass catcher often for damage or deterioration. Through normal use it will wear.
MAINTENANCE MUFFLER WATER WASHOUT FEATURE (See Fig. 16) Inspect and replace corroded muffler as it could create a fire hazard and/or damage. Your lawn mower is equipped with a fitting that allows quick and easy cleaning of the underside of the housing. To use this feature, proceed as follows: 1. Move lawn mower to an area of cut grass or another hard surface. NOTE: Water, grass and other debris will drain from beneath the mower housing during the washout process. 2.
SERVICE AND ADJUSTMENTS CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug. LAWN MOWER TO ADJUST CUTTING HEIGHT See “TO ADJUST CUTTING HEIGHT” in the Operation section of this manual.
SERVICE AND ADJUSTMENTS TO ADJUST HANDLE (See Fig. 18) ENGINE The handle on your lawn mower has three (3) height positions - adjust to height that suits you. 1. Remove knob and carriage bolt on one side of the lower handle. 2. While holding handle assembly, remove knob and carriage bolt from opposite side, align hole in handle with desired hole in handle bracket and reassemble bolt and knob and tighten securely. 3. Align opposite side of handle with same positioning hole and secure with bolt and knob.
STORAGE ENGINE MOWING POSITION OPERATOR PRESENCE CONTROL BAR FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.
TROUBLESHOOTING POINTS PROBLEM Does not start CAUSE 1. Dirty air filter. 2. Out of fuel. 3. Stale fuel. 4. 5. 6. 7. 8. 9. 10. 11. 12. Loss of power CORRECTION 1. Clean/replace air filter. 2. Fill fuel tank. 3. Empty fuel tank and refill tank with fresh, clean gasoline. Water in fuel. 4. Empty fuel tank and refill tank with fresh, clean gasoline. Spark plug wire is disconnected. 5. Connect wire to plug. Bad spark plug. 6. Replace spark plug. Loose blade or broken blade adapter. 7.
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this Husqvarna® product. Certain components (e.g.
(a) Abrasion to mower decks; (b) Tires damaged by external punctures; (c) Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) Failure to provide or perform required maintenance services as prescribed
Consumer Wheeled Limited Warranty Chart 2012 Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty Fabricated Deck shell. Limited Lifetime Warranty Battery Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only ) Engine* Transmission ** RZ4623 (967009801 & 967009802) RZ5426 (967003601 & 967003602) - stamped deck shell.
Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal, household use only) Product/Component Spreader Robotic Mowers Robotic Mower Battery Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Parts (e.g., belts, blades, etc.
RÈGLES DE SÉCURITÉ Conseils pour l’utilisation en toute sécurité des tondeuses IMPORTANT: CETTE MACHINE COUPANTE EST CAPABLE D’AMPUTER LES MAINS, LES PIEDS ET DE PROJETER DES OBJETS. L’INOBSERVATION DES RÈGLES DE SÉCURITÉ SUIVANTES PUET ETRE LA CAUSE DES BLESSURES SÉRIEUSES ET ÉVENTUELLEMENT MORTELLES. vers l’opérateur. Arrêtez les lames lorsque vous passez sur du gravillon. Ce symbole signale les points importants en • N’utilisez jamais la machine si les protections, les plateaux matière de sécurité.
• • • • • • • • • N’utilisez qu’un bidon homologué. N’enlevez jamais le bouchon et n’ajoutez jamais de carburant lorsque le moteur est en marche. Laissez le moteur refroidir avant de le remplir. Ne remplissez jamais le réservoir à l’intérieur. Ne rangez jamais ni l’appareil ni le bidon dans un endroit où se trouve une flamme nue, des étincelles ou une flamme pilote (chauffe-eau ou autres appareils). Ne remplissez jamais les bidons dans une voiture, un camion ou une remorque revêtue de plastique.
MONTAGE Lisez complètement ces instructions et ce manuel dans sa totalité avant de tenter de monter ou d’utiliser votre nouvelle tondeuse à gazon. IMPORTANT: CETTE TONDEUSE À GAZON EST FOURNIE AVEC MOTEUR SANS HUILE OU ESSENCE. Votre nouvelle tondeuse à gazon a été montée à l’usine sauf les pièces qui ne sont pas montées à cause de l’expédition. Toutes les pièces comme les écrous, les rondelles, les boulons, etc. qui sont nécessaires à compléter le montage ont été mises dans le sac des pièces.
UTILISATION CONNAISSEZ SUR VOTRE TONDEUSE À GAZON LISEZ CE MANUEL DE PROPRIÉTAIRE ET LES RÈGLES DE SÉCURITÉ AVANT D’UTILISER VOTRE TONDEUSE À GAZON. Comparez les illustrations avec votre tondeuse à gazon afin de se mettre au courant des positions des différentes commandes et des différents réglages. Conservez ce manuel pour la référence d’avenir. Ces symboles peuvent se montrer sur votre motovineuse à gazon ou dans les publications fournies avec le produit.
UTILISATION L’utilisation d’une tondeuse à gazon présente le risque de projection des particules dans les yeux qui peuvent causer des blessures sérieuses. Portez toujours des lunettes de sécurité ou une visière des yeux avant d’utiliser votre tondeuse à gazon, ou de faire tout réparations et tout réglages. Nous recommandons une visière de sécurité panoramique pour ceux qui portent des verres correctives ou des lunettes de sécurité standard. COMMENT UTILISER VOTRE TONDEUSE À GAZON 2. 3.
UTILISATION 3. Vider coupures avec le ramasse-herbe. REMARQUE: Ne traînez pas le sac quand vous le videz. Ceci l’userait inutilement. PORTE ARRIÈRE SUPPORT DU RAMASSE-HERBE POIGNÉE DU RAMASSEHERBE POIGNÉE DU CADRE DE RAMASSEHERBE CROCHET DU RAMASSE-HERBE POIGNÉE DE RAMASSE-HERBE FIG. 7 DECHARGEMENT LATÉRAL (Voir Fig. 8) • FIG. 9 Soulevez la porte arrière et installez les bras de la barre du déflecteur de l’herbe coupée dans les fentes des supports du guidon comme montré.
UTILISATION • ATTENTION: Les carburants mélangés avec l’alcool (appelés gasohol ou utilisant l’éthanol ou le méthanol) peuvent attirer l’humidité qui cause la séparation et la formation d’acide pendant l’entreposage. Le gaz acide peut endommager le système d’essence d’un moteur pendant l’entreposage. Pour éviter les problèmes avec le moteur, le système d’essence doit être vidangé avant l’entreposage de 30 jours ou plus.
ENTRETIEN AVANT APRÈS TOUTES TOUTES LES TOUTES AVANT CHAQUE CHAQUE LES 10 25 HEURES LES 100 L'ENTREUTILISATION UTILISATION HEURES OU SAISON HEURES POSAGE Vérifiez l'intégrité des systèmes de fixation Nettoyez / Vérifiez le Ramasse-Herbe * Vérifier les Pneus Vérifier les Roues d'entraînement *** Nettoyez la Tondeuse **** Nettoyez sous le Couvercle d'entraînement *** Vérifiez la Courroie et les Poulies *** Vérifiez / Aiguisez / Remplacez la Lame Tableau de lubrification Nettoyez / Rechargez la Batteie ** Véri
ENTRETIEN TONDEUSE À GAZON • Le couple de serrage recommandé est de 35-40 lb-pi. IMPORTANT: LE BOULON DE LAME EST TRAITÉ À LA CHALEUR. SI LE BOULON A BESOIN REMPLACER, REMPLACEZ SEULEMENT PAR LE BOULON APPROUVÉ MONTRÉ DANS LA SECTION DE PIÈCES DE RECHANGE DE CE MANUEL. Observez toujours les règles de sécurité quand vous faites l’entretien.
ENTRETIEN RAMASSE-HERBE • • 7. Le ramasse-herbe peut être arrosé, mais il doit être sec avant de l’utiliser. Vérifiez souvent votre ramasse-herbe pour assurer qu’il n’est pas avarié ou usé. Il s’usera sous une utilisation normale. Remplacez-le si nécessaire avec un ramasse-herbe approuvé par le fabricant. Donnez le numéro de modèle de la tondeuse à gazon lorsque vous commandez. 8. 9. Continuez d’ajouter un peu d’huile, revérifiant le jauge d'huile jusqu’à ce que le niveau d’huile arrange à plein (FULL).
ENTRETIEN SILENCIEUX LE DISPOSITIF DE LAVAGE DE L’EAU (Voir Fig. 16) Inspectez et remplacez le silencieux corrodé pour éviter les risques d’incendie et/ou les dégâts. Votre tondeuse à gazon est équipé d’un ajustage qui permet le nettoyage rapide et facile du dessous du logement. Pour employer ce dispositif, opérez comme suit: 1. Déplacez la tondeuse à gazon à un secteur d’une herbe coupée ou d’une surface dure différente.
RÉVISION ET RÉGLAGES ATTENTION: AVANT D’EFFECTUER TOUS LES RÉVISION OU RÉGLAGES: 1. Relâchez la barre de commande et arrêtez le moteur. 2. Assurez-vous que la lame et toutes les pièces mobiles soient arrêtées complètement. 3. Débranchez le fil de bougie d’allumage et posez-le de telle façon qu’il ne puisse pas entrer en contact avec la bougie d’allumage. TONDEUSE À GAZON POUR RÉGLER LA HAUTEUR DE COUPE Voir “RÉGLER LA HAUTEUR DE COUPE” dans la section d’utilisation de ce manuel.
RÉVISION ET RÉGLAGES POUR RÉGLER LE GUIDON (Voir Fig. 18) MOTEUR Le guidon de la tondeuse à gazon a trois (3) positions de hauteur - réglez-le à une hauteur confortable. 1. Enlevez le bouton et le boulon de chariot sur un (1) côté du guidon inférieur. 2. Lorsque vous tenez l’ensemble du guidon, enlevez le bouton et le boulon de chariot de l’autre côté, alignez le trou dans le guidon avec le trou désiré dans le support de guidon puis replacez le boulon et le bouton et serrez à fond. 3.
ENTREPOSAGE MOTEUR POSITION DE TONTE BARRE DE COMMANDE DE PRÉSENCE D’OPÉRATEUR SYSTÈME D’ESSENCE IMPORTANT: IL EST IMPORTANT DE PRÉVENIR, PENDANT L’ENTREPOSAGE, LES DÉPÔTS DE GOMME DANS LES PARTIES ESSENTIELLES DU SYSTÈME D’ESSENCE TELLES QUE LE CARBURATEUR, LE FILTRE À ESSENCE, LES CONDUITES D’ESSENCE, OU LE RÉSERVOIR D’ESSENCE. LES ESSENCES CONTENANT DE L’ALCOOL (ÉTHANOL OU MÉTHANOL ET PARFOIS APPELÉES GASOHOL) PEUVENT ABSORBER DE L’HUMIDITÉ.
GUIDE DE DÉPANNAGE PROBLÈME Le moteur refuse de démarrer CAUSE SOLUTION 1. 2. 3. Filtre à air sale Sans essence. Essence trop vieille. 1. 2. 3. 4. Eau dans l’essence. 4. 5. 6. 7. 8. 9. 10. Le moteur manque de puissance Nettoyez/remplacez le filtre à air. Remplissez réservoir d’essence. Vidangez le réservoir et remplissez-le avec de l'essence fraîche et propre. Vidangez le réservoir et remplissez-le avec de l'essence fraîche et propre. Branchez le fil de bougie d’allumage à la bougie.
Produits sur roues de consommateur – Garantie limitée Husqvarna garantit à l’acheteur original que ce produit HusqvarnaMD est exempt de vices de matériaux ou de fabrication sous des conditions normales d’utilisation et d’entretien à compter de la date d’achat au détail pour la période de garantie applicable indiquée à l’annexe A. Cette garantie ne peut être transférée à aucun aquéreur subséquent de ce produit Husqvarna®. Certains composants (p. ex.
a. Montage et service de préparation avant livraison, mises au point du moteur. b. Réglages après les premiers trente (30) jours de l’achat et au-delà, tel que réglages du câble d’accélérateur, des guides de courroie. c. L’entretien préventif comme décrit dans le manuel de l’utilisateur. De plus, vous devez cesser immédiatement l’utilisation du produit lors d’une défaillance ou d’un dommage quelconque.
Tableau de garantie limitée des produits sur roues de consommateur 2012 Consommateur (perso Commercial (toute utilisation nnel, utilisation commerciale, professionnelle, domestique seulement) institutionnelle, agricole ou à revenu de production, sauf l’utilisation en location) Produit/composant Tondeuses à siège : Cadre, châssis, essieu avant 5 ans * Moteur* ( Husqvarna/Peerless) 3 ans Transmission (si tierce partie)** ** Modèless XLS Models uniquement - coque d'unité de coupe étampée.
Tableau de garantie limitée des produits sur roues de consommateur 2012 Produit/composant Générateurs Moteur* Autres composants non réutilisables* Épandeuses Épandeuse Tondeuses robotiques Tondeuse robotique Batterie Pièces et accessoires (si acheté) Consommateur (perso Commercial (toute utilisation nnel, utilisation commerciale, professionnelle, domestique seulement) institutionnelle, agricole ou à revenu de production, sauf l’utilisation en location) Annexe A Location (toute utilisation en location) *
12/06/2011 BY