Operators Manual
Table Of Contents
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Assembling the handlebar and throttle
- Assembling the cutting equipment
- Fitting the guard extension
- Fitting a blade guard, grass blade and grass cutter
- Fitting the blade guard and saw blade
- Fitting other guards and cutting attachments
- Adjusting the harness and brush cutter
- Standard harness
- Triobalance harness
- Fuel safety
- Fuel
- Fuelling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Muffler
- Cooling system
- Bevel gear
- Air filter
- Spark plug
- Maintenance schedule
- Technical data
- EC-declaration of conformity (Applies to Europe only)
32 – English
TECHNICAL DATA
EC-declaration of conformity (Applies to Europe only)
We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the brush cutters Husqvarna
333R, 335FR and 335RX
with serial numbers dating from 2009 onwards (the year is clearly stated on the rating plate,
followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:
- of May 17, 2006 "relating to machinery" 2006/42/EC
- of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. Conformity assessment according
to Annex V. For information relating to noise emissions, see the chapter Technical data.
The following standards have been applied: EN292-2:1992, CISPR 12:2005, EN ISO 11806:1997
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type
examination on behalf of Husqvarna AB. The certificates are numbered:
SEC/09/2135, 01/164/044, 01/164/046 -
335RX, 335FR,
SEC/09/2134, 01/164/045, 01/164/047 - 333R.
Huskvarna December 29, 2009
Bo Jonsson, Development manager (Authorized representative for Husqvarna AB and responsible for technical
documentation.)
Approved accessories Type Cutting attachment guard, Art. no.
Centre hole in blades/cutters, Ø 25,4
mm
Output shaft thread M12
Grass blade/grass cutter
Multi 255-3 (Ø 255 3 teeth) 537 33 16-01
Grass 255-4 (Ø 255 4 teeth) 537 33 16-01
Multi 275-4 (Ø 275 4 teeth) 537 33 16-01
Multi 300-3 (Ø 300 3 teeth) 537 33 16-01
Saw blade Scarlet 200-22 (Ø 200 22 teeth) 537 38 77-01
Plastic blades
Tricut Ø 300 mm (Separate blades
have part number 531 01 77-15)
537 33 16-01 / 537 34 94-01
Trimmer head
T35, T35x (Ø 2.4 - 3.0 mm cord) 537 33 16-01 / 537 34 94-01
S35 (Ø 2.4 - 3.0 mm cord) 537 33 16-01 / 537 34 94-01
T45x (Ø 2.7 - 3.3 mm cord) 537 33 16-01 / 537 34 94-01
Auto 55 (Ø 2.7 - 3.3 mm cord) 537 33 16-01 / 537 34 94-01
Trimmy S II (Ø 2.4 - 3.3 mm cord) 537 33 16-01 / 537 34 94-01
Support cup 503 89 01-02 -