Item #1003-152-010 Model #072-0030H USE AND CARE GUIDE AUTOMATIC ELECTRONIC TANK DRAIN Questions, problems, missing parts? Before returning to the store, call Husky Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-888-HD-HUSKY HUSKYTOOLS.COM 200-3132-E_7-23-19 THANK YOU We appreciate the trust and confidence you have placed in Husky through the purchase of this air compressor accessory. We strive to continually create quality products designed to enhance your home.
Table of Contents Safety Information.....................................2 Work Area Safety....................................2 Personal Safety ......................................2 Warranty....................................................3 Pre-Installation..........................................4 Specifications.........................................4 Package Contents...................................4 Planning Installation...............................4 Installation.............................
Warranty LIMITED WARRANTY WHAT IS COVERED The manufacturer warrants to the original retail purchaser that this product is free from defect in material and workmanship and agrees to repair or replace, at the manufacturer’s discretion, any defective product free of charge within these time periods from the date of purchase.
Pre-Installation SPECIFICATIONS Cycle Time 0.5 - 45 Minutes Discharge Time 0.5 - 10 Seconds Supply Voltage 120V, 15A Environmental Protect Nema 4 Operating Temperature 33°F - 140°F Maximum Pressure 230 PSI Orifice Size 3/16 in. A HLA1683066 Item #1003-152-010 Model #072-0030H B C USE AND CARE GUIDE D AUTOMATIC ELECTRONIC TANK DRAIN Questions, problems, missing parts? Before returning to the store, call Husky Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m.
Installation Installing the automatic electronic tank drain 1 NOTE: Use thread sealer or Teflon® on all male threads. □□ Install the elbow end of the flexible drain tube (J) into the bottom of the tank. Tighten using and adjustable wrench. □□ Attach the strainer ball valve (C) to the back of the electronic automatic tank drain assembly (B). Tighten using an adjustable wrench. □□ Attach the straight swivel end of the flexible drain tube (A) into the end of the strainer ball valve (C).
Operation Using the Electronic 1Automatic Tank Drain Fig. 5 OPEN WARNING: Do not operate the Electronic Automatic Tank Drain outside the following pressure and temperature ranges. Maximum pressure 230 psi Compressed air temperature 33 to 265°F Ambient temperature 33 to 140°F CLOSE □□ Open the strainer ball valve (see Fig. 5). □□ Set the “time off” and “time on” knobs on front of the electronic automatic drain assembly (B) (see Timer Settings section).
Maintenance and Cleaning 1 Maintaining the Electronic Automatic CAUTION: Always wear ANSI X87.1 approved safety goggles when performing maintenance. High pressure can cause injury from flying debris. Tank Drain To clean the strainer ball valve assembly: □□ Turn the self cleaning valve to the “OPEN” position for 1-2 seconds. This will blow out any debris that may be in the valve. □□ Turn the self cleaning valve to the “CLOSED” position.
Questions, problems, missing parts? Before returning to the store, call Husky Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday 1-888-HD-HUSKY HUSKYTOOLS.COM Retain this manual for future use.
Artículo n.º1003-152-010 Modelo nº 072-0030H GUÍA DE USO Y CUIDADO DRENAJE DE TANQUE ELECTRÓNICO AUTOMÁTICO ¿Tiene preguntas o problemas, o le faltan piezas? Antes de regresar a la tienda, llame al Servicio de Atención al Cliente de Husky Lunes a viernes de 8:00 a.m. a 7:00 p.m., EST, y los sábados de 9:00 a.m. a 6:00 p.m., EST 1-888-HD-HUSKY HUSKYTOOLS.COM 200-3132-E_7-23-19 GRACIAS Agradecemos la confianza que ha depositado en Husky a través de la compra de este accesorio para compresor de aire.
Índice Información de seguridad.........................2 Seguridad en el área de trabajo..............2 Seguridad personal ................................2 Garantía.....................................................3 Preinstalación............................................4 Especificaciones.....................................4 Contenido del paquete............................4 Planificación de la instalación................4 Instalación.................................................
Garantía GARANTÍA LIMITADA QUÉ ES LO QUE CUBRE El fabricante garantiza al comprador minorista original que este producto está libre de defectos de material y mano de obra, y acepta reparar o reemplazar, a discreción del fabricante, cualquier producto defectuoso sin cargo dentro de estos períodos de tiempo desde la fecha de la compra.
Antes de la instalación ESPECIFICACIONES Tiempo de ciclo 0.5 - 45 minutos Tiempo de descarga 0.5 - 10 segundos Tensión de alimentación 120V, 15A Protección ambiental Nema 4 Temperatura de funcionamiento 33 °F - 140 °F Presión máxima 230 PSI Tamaño del orificio 3/16 pulg. A Artículo n.
Instalación Instalación del drenaje de tanque electrónico automático 1 NOTA: Use sellador de rosca o Teflon® en todas las roscas macho. □□ Instale el extremo del codo del tubo de drenaje flexible (J) en la parte inferior del tanque. Ajuste con una llave ajustable. □□ Coloque la válvula de bola con filtro (C) en la parte posterior del conjunto de drenaje de tanque automático electrónico (B). Ajuste con una llave ajustable.
Funcionamiento Uso del drenaje de tanque 1electrónico automático Figura 5 Presión máxima 230 PSI Temperatura del aire comprimido 33 a 265 °F Temperatura ambiente 33 a 140 °F CERRAR □□ Abra la válvula de bola con filtro (consulte la figura 5). □□ Ajuste las perillas “time off” (tiempo de apagado) y “time on” (tiempo de encendido) parte delantera del conjunto de drenaje automático electrónico (B) (consulte la sección Ajuste del tiempo).
Mantenimiento y limpieza 1 Mantenimiento del drenaje de tanque PRECAUCIÓN: Siempre use gafas de seguridad aprobadas por ANSI X87.1 al dar mantenimiento. La presión alta puede proyectar desechos voladores y causar lesiones. automático electrónico Para limpiar el conjunto de válvula de bola con filtro: □□ Gire la válvula de limpieza automática a la posición “OPEN” (abierta) por 1 o 2 segundos. Esto despejará cualquier desecho que pueda haber en la válvula.
¿Preguntas, problemas, piezas que faltan? Antes de regresar a la tienda, llame al Servicio de Atención al Cliente de Husky Lunes a viernes, de 8:00 a 19:00 hs (hora del Este) Sábados de 9:00 a 18:00 hs (hora del Este) 1-888-HD-HUSKY HUSKYTOOLS.COM Conserve este manual para su consulta futura.