Loki Installation Manual Model: 51039 Matte Silver 51040 Brushed Nickel 51042 Antique Copper 59385 Fresh White 59386 Polished Nickel 59387 Noble Bronze Fan weight ±2 lbs: 17.6 lbs (8.0 kg) ©2020 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
1886 Hanging the Fan S li d e c a n o p y ove NOTICE rd o wn ro d an d To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. w i re s . Place the downrod ball into the slot in the ceiling bracket. Progress Check: Your fan should look like this. Note: Fan style may vary.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw y op Fi t t h e c a n in pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Attach each blade to a blade iron using the grommets, found in the and the shoulder screws, found in the hardware bag.
1886 Assembling the LIght Kit 2 of 3 bag Light Kit Screw Feed the 9-pin plug connector coming from the bottom of the motor housing through the center hole in the light kit assembly. Connect it to the plug connector found in the switch housing area of the light kit assembly. Make sure to line up the colored markings on the connectors. Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose.
1886 Installing the Pull Chains The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. Remove and discard the plastic connectors from the ends of the short pull chain. Attach the pull chain pendants to the light and fan pull chains. Repeat x2 Reversing the Fan Ceiling fans work in two directions: downdraft and updraft. To change the direction of air flow, turn the fan off and let it come to a complete stop.
1886 Troubleshooting Fan Doesn’t Work Excessive Wobbling • Make sure power switch is on. • Make sure the blades are properly installed on the blade iron posts. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe 1 2 10 3 9 4 8 5 7 6 Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly. • VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
