Product Data Sheet / Brochure

QuickSpecs
HPE ProLiant ML350 Gen10 Server
Configuration Information
Page 28
This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales
representative for information on configurable product offerings and requirements.
1. Factory Integrated Models must start with a CTO Server.
2. FIO indicates that this option is only available as a factory installable option.
3. All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives
ordered with the server.
4. Some options may not be integrated at the factory. Contact your local sales representative for additional information.
European Union (EU) eco-design regulations for server and storage products, known as Lot 9, go into effect on March 1st, 2020.
Among other requirements, for servers this directive establishes power thresholds for idle state, as well as efficiency and
performance in active state which vary among co
nfigurations. HPE ProLiant Gen10 servers are compliant with Lot9 requirements.
For more information regarding HPE Lot 9 conformance, please visit:
https://www.hpe.com/us/en/about/environment/msds-specs-more.html
Step 1: Base Configuration
(choose one of the following configurable models)
CTO Server
HPE ML350 Gen10 4 LFF
CTO Server
HPE ML350 Gen10 8 SFF
CTO Server
HPE ML350 Gen10 8 SFF
Rack CTO Server
SKU Number
877625-B21
877626-B21
877627-B21
Processor Sockets
Two as standard
Two as standard
Two as standard
Processor
Not included as standard
Not included as standard
Not included as standard
DIMM Slots
24-DIMM slots
24-DIMM slots
24-DIMM slots
Storage Controller
Embedded SW RAID S100i with 14 SATA ports, choice of HPE modular Smart Array (AROC)
and/or PCIe Standup controller card (s)
PCIe
8 PCIe Gen3 slots (x16, x8, x16, x8, x16, x8, x16, x8) as standard
Notes:
PCIe slots 5 – 8 require the second processor to enable.
Drive Cage - included
4 LFF
8 SFF
8 SFF
Network Controller
Embedded 4x1GbE HPE Ethernet 1Gb 4-port 369i Adapter with optional 1/10/25Gb Standup
card
Notes: embedded 4x1GbE HPE Ethernet 1Gb 4-port 369i Adapter does not support speeds of
100MB/s and 10MB/s.
Fans
2-Standard
2-Standard
6-Standard
Power Supply Cage
included
HPE Flex Slot RPS cage and
PDB included
HPE Flex Slot RPS cage and
PDB included
HPE Flex Slot RPS cage and
PDB included
Management
HPE iLO with Intelligent Provisioning (standard), iLO Advances and OneView (optional)
USB
6x 3.0/2.0 standard plus front
iLO Service Port
6x 3.0/2.0 standard plus front
iLO Service Port
6x 3.0/2.0 standard plus front
iLO Service Port
Tower-to-Rack
conversion kit
Optional
Notes: Please select 874578-
B21 (Tower-to-Rack
Conversion kit) under the Ad-
Hoc category. This way the
system will not trigger build
error under CLIC check.
Optional
Notes: Please select 874578-
B21 (Tower-to-Rack
Conversion kit) under the Ad-
Hoc category. This way the
system will not trigger build
error under CLIC check.
Easy Install rack-rail tray (1U)
with CMA included as
mandatory (must-select)
accessories
Notes
: Refer to HPE Power Advisor Tool to review the power requirement for your selected configuration and determine what
power supply module(s) to select.