- HP Printer User Manual
Table Of Contents
- hpLaserJet 9055mfp (Q3631A) hpLaserJet 9065mfp (Q3632A)
- service manual
- Contents
- How to use this manual
- Safety
- MFP overview
- Overview of system
- hpLaserJet9055mfp/9065mfp product specifications
- Central cross-sectional view
- Drive system diagram
- Fuser/web drive section
- Drum drive section
- Developing drive section
- Paper feed/vertical conveyance/tray up drive sections
- Tray1 paper feed/automatic duplex unit (ADU) pre-registration drive section
- Charging and transfer/separation wire cleaning drive section
- Automatic Duplex Unit (ADU) conveyance drive section
- Paper exit drive section
- Toner supply drive section
- Optics drive section
- MFP unit explanation
- MFP disassembly/assembly
- External section
- Drive section
- Scanner section
- Laser scanner unit
- Drum unit
- Corona unit
- Screws that must not be removed
- Removing and reinstalling the charging corona unit
- Removing and reinstalling the charge control plate
- Replacing the charging wires
- Removing and reinstalling the charging wire cleaning unit
- Removing and reinstalling the PCL
- Cleaning the charging corona unit/PCL
- Removing and reinstalling the transfer/separation corona unit
- Removing and reinstalling the plunger prevention plate
- Replacing the transfer/separation wires and transfer/separation wire cleaning block
- Removing and reinstalling the TSL unit
- Developing unit
- Toner supply unit
- Cleaning/toner recycle unit
- Paper feed units of Trays2 and3
- Removing and reinstalling the paper feed unit
- Removing and reinstalling the paper feed Trays2 and3
- Removing and reinstalling the paper pick roller and pick roller rubber
- Removing and reinstalling the separation roller rubber
- Replacing the pre-registration and feed clutches (MCs)
- Replacing the wires
- Wire lengths
- Installing wires
- Paper feed unit of Tray3
- Removing and reinstalling the paper feed unit
- Removing and reinstalling paper feed Tray 3
- Removing and reinstalling the paper pick roller and pick roller rubber
- Removing and reinstalling the separation roller rubber
- Replacing the pre-registration and feed clutches (MCs)
- Replacing the wires
- Wire lengths
- Installing wires
- Tray1
- Vertical conveyance section
- ADF unit
- Pulling out and reinstalling the ADU stand
- Cleaning the paper mis-centering PS (PS70)/leading edge PS (PS43)
- Removing and reinstalling the registration MC (MC1)
- Removing and reinstalling the second paper feed unit (registration assembly)
- Cleaning the registration PS (PS44)
- Removing and reinstalling the registration roller
- Removing and reinstalling the pre-transfer roller
- Cleaning the automatic document feeder paper reverse PS (PS45)/ Reverse/Exit PS (PS46)
- Removing and reinstalling the ADF reverse roller
- Removing and reinstalling the ADU stand
- Removing and reinstalling the pre-registration roller
- Removing and reinstalling the ADU conveyance roller3 and4
- Removing and reinstalling the ADU conveyance roller1 and2
- Removing and reinstalling the paper reverse/exit roller
- Fuser
- Removing and reinstalling the fuser
- Removing and reinstalling the fuser (top)
- Removing and reinstalling the web cover
- Removing and reinstalling the cleaning web
- Replacing the fusing heater lamps (L2, L3)
- Replacing the fusing heater lamp (L4)
- Removing and reinstalling the fusing separation claw (upper) unit and fusing separation claws (up...
- Removing and reinstalling the fusing separation claw (lower) unit and fusing separation claws (lo...
- Removing and reinstalling the fusing upper roller
- Removing and reinstalling the fusing lower roller
- Removing and reinstalling the decurler roller
- Removing and reinstalling the fusing temperature sensors1 and2
- Removing and reinstalling the thermostat/U (TS1)
- Removing and reinstalling the thermostat/L (TS2)
- Product comparison
- Environmental Product Stewardship Program
- Terminology cross-reference
- Index
- automatic document feeder (Q3644A)
- 4000-sheet high capacity input (A4/Letter - Q3637A) (A3/Ledger - Q3638A)
- Contents
- HCI overview
- HCI unit explanation
- HCI disassembly/assembly
- Explanation
- Paper feed section
- Cleaning the paper dust removing brush
- Cleaning the HCI feed PS (PS106)/HCI first paper feed PS (PS107)
- Removing and reinstalling the pick roller unit
- Replacing the pick roller rubber/feed roller rubber
- Replacing the separation roller rubber
- Replacing the HCI feed MC (MC101)/HCI first paper feed MC (MC102)
- Replacing the Q3637A up/down wires
- Replacing the Q3638A up/down wires
- Index
- stapler/stacker (Q3633A) multifunction finisher (Q3634A)
- Contents
- Finisher overview
- Finisher unit explanation
- Finisher disassembly/assembly
- External section
- Removing and reinstalling the booklet tray (Q3634A only)
- Removing and reinstalling the top cover/1
- Removing and reinstalling the top cover/2
- Removing and reinstalling the side cover
- Removing and reinstalling the front door
- Removing and reinstalling the rear cover
- Removing and reinstalling the main tray
- Removing and reinstalling the main paper exit opening cover
- Removing and reinstalling the booklet paper exit opening cover (Q3634A only)
- Conveyance section
- Main tray section
- Stacker section
- Stapler section
- External section
- Index
- post insertion kit (Q3636A)
- punch kit (Q3689A, Q3635A, Q3690A, Q3691A)
ENWW Main tray section 73
Finisher
disassembly/assembly
9 Attach a spring scale to the hole on the top
of the belt tensioner. Pull the spring scale
upward until a tension of 2.5 ± 0.25 kg is
indicated. Tighten the two screws.
10 Loosen the two screws securing the front
wire bracket. Adjust the height of the
front wire bracket to level the up/down
stay. Tighten the four mounting screws
on the wire brackets (front and rear).
CAUTION Make sure the up/down
stay is level. If the stay is
not level, an unnecessary
load is put on the tray
up/down motor or gear,
which can result in damage
to these components.
11 Reinstall the above parts following the
removal steps in reverse.
A = 2.5 0.25kg
Screws
Belt tensioner
Mounting
screws
Wire bracket
Wire bracket
Up/down stay
Screws