HP 500 Notebook PC Maintenance and Service Guide
© Copyright 2006 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel, Pentium, and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. The information contained herein is subject to change without notice.
Table of contents 1 Product description 2 External component identification Top components ................................................................................................................................... 4 Pointing devices ................................................................................................................... 4 Keys .....................................................................................................................................
Hard drive .......................................................................................................................... 29 Computer feet .................................................................................................................... 31 Memory module ................................................................................................................. 31 Mini PCI card module .........................................................................................
Backing up the entire hard drive ........................................................................................ 92 Backing up modifications made to the system ................................................................... 93 Scheduling backups ........................................................................................................... 93 Recovery .....................................................................................................................................
1 Product description Category Description Product Name HP 500 Notebook PC Processors Intel® Pentium® M 740 (1.73 GHz) Processor 533-MHz front side bus (FSB), 1-MB L2 cache, socketed System board System board System board 910GML without wireless local area network (WLAN) 910GML with WLAN 915GM with WLAN √ √ √ √ Intel Celeron® M Processor 400-MHz FSB, 512-KB L2 cache, socketed: Chipset √ √ ICP 350M (1.
Category Hard drives Description ● Supports all 9.5-mm, 2.5-inch hard drives ● Parallel ATA System board System board System board 910GML without wireless local area network (WLAN) 910GML with WLAN 915GM with WLAN √ √ √ 60 GB, 5400 rpm Optical drives (fixed) √ 40 GB, 4200 rpm √ √ √ ● 12.
Category Description 2-pin AC jack System board System board System board 910GML without wireless local area network (WLAN) 910GML with WLAN 915GM with WLAN √ √ √ Docking Docking support Keyboard/ pointing devices Keyboard with embedded numeric keypad √ √ √ TouchPad with 2 buttons and one-way scroll √ √ √ 4-cell, 2.
2 External component identification Top components Pointing devices 4 Item Component Function (1) TouchPad Moves the pointer and selects or activates items on the screen. (2) Left TouchPad button Functions like the left button on an external mouse. (3) Right TouchPad button Functions like the right button on an external mouse. (4) TouchPad scroll zone Scrolls up or down.
Keys ENWW Item Component Function (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. (5) Embedded numeric keypad keys Can be used like the keys on an external numeric keypad.
Buttons and lights Item Component Function (1) Caps lock light On: Caps lock is on. (2) Internal display switch Turns off the display if the display is closed while the power is on. (3) Wireless button (select models only) Turns the wireless feature on or off, but does not create a wireless connection. NOTE A wireless network must be set up in order to establish a wireless connection.
Front components ENWW Item Component Function (1) Wireless antennae (select models only) Send and receive signals from one or more wireless devices. (2) Battery light ● On: A battery is charging. ● Blinking: A battery that is the only available power source has reached a low-battery condition. When the battery reaches a critical low-battery condition, the battery light begins to blink rapidly.
Right-side components Item Component Function (1) Optical drive Reads an optical disc. (2) Security cable slot Attaches an optional security cable to the computer. NOTE The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
Left-side components Item Component Function (1) Vent Enables airflow to cool internal components. CAUTION To prevent overheating, do not obstruct vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or thick rugs or clothing, to block airflow. NOTE The computer fan starts up automatically to cool internal components and prevent overheating.
Bottom components Item Component Function (1) Battery bay Holds the battery. NOTE The HP 500 Notebook PC does not support Smart Battery technology. (2) Battery release latches (2) Release the battery from the battery bay. (3) Hard drive bay Holds the hard drive. (4) Vent Enables airflow to cool internal components. CAUTION To prevent overheating, do not obstruct vents. Use the computer only on a hard, flat surface.
3 Unknown user password If the computer you are servicing has an unknown user password, follow these steps to clear the password. NOTE These steps also clear CMOS. Before disassembling the computer, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. 4.
4 Illustrated parts catalog Serial number location When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer.
Computer major components Item Description (1) Display assemblies Spare part number 14.
Item (2) (3) Spare part number 14.1-inch, WXGA AntiGlare display assembly for use only with computer models without wireless LAN capability 438549-001 14.0-inch, WXGA AntiGlare display assembly for use only with computer models with wireless LAN capability (includes wireless antenna transceivers and cables) 438548-001 14.
Item Description (9a) Memory/Mini PCI card module cover (includes 1 captive screw, secured by a C clip) (9b) Hard drive cover (includes 2 captive screws, secured by C clips) (10) Heat sink (includes thermal paste) (11) System boards (12) Spare part number 438529-001 915GM (for use only with computer models with wireless LAN capability) 438521-001 910GML (for use only with computer models with wireless LAN capability) 438520-001 910GML (for use only with computer models without wireless LAN
Display assembly components 16 Item Description (1) Display bezels Spare part number For use with 14.1-inch display panels 438535-001 For use with 14.0-inch display panels 438534-001 (2) Display Hinge Kit 438536-001 (3) Display panels 14.1-inch, WXGA AntiGlare display panel 438541-001 14.
Plastics/Hardware Kit Item ENWW Description Spare part number Plastics/Hardware Kit 438552-001 (1) Hard drive cover (includes 2 captive screws, secured by C clips) (2) Memory/Mini PCI card module cover (includes 1 captive screw, secured by a C clip) Plastics/Hardware Kit 17
Mass storage devices Item Description (1) Hard drives (include frame and connector) (2) 18 Spare part number 5400 rpm, 60 GB 438526-001 4200 rpm, 40 GB 438525-001 Optical drives (include bezel and bracket) DVD±RW/R and CD-RW Double-Layer Combo Drive 438524-001 DVD±RW and CD-RW Super Multi Double-Layer Combo Drive 438523-001 Chapter 4 Illustrated parts catalog ENWW
Miscellaneous parts Description Spare part number 65-watt AC adapter 418872-001 Power cords: Australia 350055-011 Brazil 350055-201 Denmark 350055-081 Europe 350055-021 French Canada 350055-DB1 Israel 350055-BB1 Italy 350055-061 Japan 350055-291 Korea 350055-AD1 People's Republic of China 350055-AA1 Switzerland 350055-BG1 The United Kingdom 350055-031 The United States 350055-001 Screw Kit 438558-001 Phillips PM3.0×3.0 screw Phillips PM2.5×8.0 captive screw Phillips PM2.5×6.
Sequential part number listing Spare part number Description 350055-001 Power cord use in the United States 350055-011 Power cord for use in Australia 350055-021 Power cord for use in Europe 350055-031 Power cord for use in the United Kingdom 350055-061 Power cord for use in Italy 350055-081 Power cord for use in Denmark 350055-201 Power cord for use in Brazil 350055-291 Power cord for use in Japan 350055-AA1 Power cord for use in the People’s Republic of China 350055-AD1 Power cord for
ENWW Spare part number Description 438527-001 PC Card slot bezel 438528-001 Fan assembly 438529-001 Heat sink 438530-001 Display inverter 438531-001 Keyboard for use in the United States 438531-021 Keyboard for use internationally 438531-031 Keyboard for use in the United Kingdom 438531-051 Keyboard for use in France 438531-141 Keyboard for use in Turkey 438531-151 Keyboard for use in Greece 438531-161 Keyboard for use in Latin America 438531-171 Keyboard for use in Saudi Arabia 4
22 Spare part number Description 434545-001 1-DIMM, PC2-4200, 256-MB memory module 438546-001 1-DIMM, PC2-4200, 512-MB memory module 438547-001 14.0-inch WXGA AntiGlare display assembly for use only with computer models without wireless LAN capability 438548-001 14.0-inch WXGA AntiGlare display assembly for use only with computer models with wireless LAN capability (includes wireless antenna transceivers and cables) 438549-001 14.
5 Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Flat-bladed screwdriver Service considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures.
Drive handling CAUTION Drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. Before handling a drive, be sure that you are discharged of static electricity.
The following table shows how humidity affects the electrostatic voltage levels generated by different activities. CAUTION A product can be degraded by as little as 700 V.
● When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials. ● Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and Styrofoam. ● Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items only at static-free workstations. ● Avoid contact with pins, leads, or circuitry. ● Turn off power and input signals before inserting or removing connectors or test equipment.
Material Use Voltage protection level Carbon-loaded plastic Floor mats 7,500 V Metallized laminate Floor mats 5,000 V Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 56 screws, in 6 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw and screw lock size and location during removal and replacement.
Battery Description Spare part number 4-cell, 2.2-Ah battery 438518-001 Before disassembling the computer, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. Remove the battery: 1. Turn the computer upside down with the rear panel toward you. 2.
Hard drive Description Spare part number 5400 rpm, 60 GB 438526-001 4200 rpm, 40 GB 438525-001 Before disassembling the computer, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. 4. Remove the battery (see Battery on page 28). Remove the hard drive: 1.
6. Remove the hard drive (3) from the hard drive bay. 7. Remove the four Phillips PM3.0×3.0 hard drive frame screws (1) from each side of the hard drive. 8. Lift the frame (2) straight up to remove it from the hard drive. Reverse this procedure to reassemble and install the hard drive.
Computer feet Description Spare part number Rubber Feet Kit 438557-001 The computer feet are adhesive-backed rubber pads. Memory module Description Spare part number 1-DIMM, PC2-4200, 512 MB 438546-001 1-DIMM, PC2-4200, 256 MB 438545-001 1-DIMM, PC2-3200, 256 MB 438544-001 Before removing the memory module, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2.
3. Lift the front edge of the cover (2) and swing it toward you. 4. Remove the memory/Mini PCI card module compartment cover. NOTE The memory/Mini PCI card module compartment cover is included in the Plastics/ Hardware Kit, spare part number 438552-001 . 5. Spread the retaining tabs (1) on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.) 6. Slide the module (2) away from the socket at an angle. 7.
Mini PCI card module Description Spare part number 802.11b/g Mini PCI card WLAN module for use in the MOW countries listed below. 390501-001 Argentina Canada Mexico The United States Brazil Chile Taiwan 802.11b/g Mini PCI card WLAN module for use in the ROW countries listed below.
Remove the Mini PCI card module: 1. Before disconnecting the wireless antenna cables, make note of which cable is attached to which antenna clip on the Mini PCI card module, then disconnect the auxiliary and main wireless antenna cables (1) from the Mini PCI card module. NOTE The wireless antenna cables are available in the Wireless Antenna Kit, spare part number 438516-001. 2. Spread the retaining tabs (2) on each side of the Mini PCI card module socket to release the Mini PCI card module.
Optical drive NOTE All optical drive spare part kits include an optical drive bezel and optical drive bracket. Description Spare part number DVD±RW and CD-RW Super Multi Double-Layer Combo Drive 438523-001 DVD±RW/R and CD-RW Double-Layer Combo Drive 438524-001 Before removing the optical drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2.
6. Remove the optical drive bracket (2). Reverse this procedure to reassemble and install the optical drive.
Switch cover Description Spare part number For use only with computer models with wireless LAN capability (includes wireless button and wireless light) 438561-001 For use only with computer models without wireless LAN capability 438560-001 Before removing the switch cover, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2.
4. Use a flat-bladed tool to gently pry the tabs on the switch cover out of the slots on the computer. 5. Turn the computer display-side up with front toward you. 6. Open the computer as far as possible. 7. Lift the rear edge of the switch cover and swing it forward. 8. Remove the switch cover. Reverse this procedure to install the switch cover.
Keyboard Description Brazil 438531-201 Russia 438531-251 The Czech Republic 438531-221 Saudi Arabia 438531-171 Europe 438531-021 Slovakia 438531-231 France 438531-051 Slovenia 438531-BA1 Greece 438531-151 South Africa 438531-AR1 Hungary 438531-211 Thailand 438531-281 Israel 438531-BB1 Turkey 438531-141 Latin America 438531-161 The United Kingdom 438531-031 Poland 438531-241 The United States 438531-001 Before removing the keyboard, follow these steps: 1.
5. Lift the rear edge of the keyboard and swing it toward you until it rests on the palm rest. 6. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached and disconnect the keyboard cable (2). 7. Remove the keyboard. Reverse this procedure to install the keyboard.
Display assembly Description Spare part number 14.1-inch, WXGA AntiGlare display assembly for use only with computer models with wireless LAN capability (includes wireless antenna transceivers and cables) 438550-001 14.1-inch, WXGA AntiGlare display assembly for use only with computer models without wireless LAN capability 438549-001 14.
42 3. Turn the computer display-side up with the front toward you. 4. Open the computer until the display assembly is in an upright position. 5. Disconnect the display cable connector(1) from the system board and remove the display cable (2) from the clips and routing channel built into the top cover. 6. Remove the wireless antenna cables (3) from the clips and routing channel built into the top cover. 7. Remove the two Phillips PM2.0×9.
9. If it is necessary to replace any of the display assembly internal subcomponents, remove the following display bezel screw covers and screws: (1) Four round rubber screw covers on the top edge of the display bezel (2) Four flat rubber screw covers on the bottom edge of the display bezel (3) Eight Phillips PM2.5×6.0 screws NOTE The display bezel screw covers are available in the Display Screw Cover Kit, spare part number 438542-001.
12. If it is necessary to replace the display inverter, remove the Phillips PM2.5×6.0 screw (1) that secures the inverter to the display enclosure. 13. Disconnect the display panel cable (2) and the backlight cable (3) from the inverter. 14. Remove the display inverter (4). NOTE The display inverter is available using spare part number 438530-001. 15. If it is necessary to replace the display panel, remove the four Phillips PM2.5×6.0 screws (1) that secure the panel to the display enclosure. 16.
17. If it is necessary to replace either of the display hinges, remove the four Phillips PM2.0×3.0 screws (1) that secure each hinge to the display panel. 18. Remove the display hinges (2). NOTE The display hinges are available in the Display Hinge Kit, spare part number 438536-001.
19. If it is necessary to replace the wireless antenna transceivers (1) and cables (2), remove the transceivers and cables from the display enclosure. NOTE The wireless antenna transceivers are attached to the display enclosure by a thin layer of adhesive. NOTE The wireless antenna transceivers and cables are available in the Wireless Antenna Kit, spare part number 438516-001. Reverse this procedure to reassemble and install the display assembly.
Remove the base enclosure: ENWW 1. Release the ZIF connector (1) to which the TouchPad cable is attached and disconnect the TouchPad cable (2). 2. Remove the Phillips PM2.0×9.0 screw (3) that secures the base enclosure to the computer. 3. Turn the computer upside down with the front toward you. 4. Remove the seven Phillips PM2.0×9.0 screws (1) and the two Phillips PM2.0×3.0 screws (2) that secure the base enclosure to the computer.
5. Lift the left side of the base enclosure (1) until the USB connectors (2) disengage from their openings in the base enclosure. 6. Remove the base enclosure. Reverse this procedure to install the base enclosure. RTC battery Description Spare part number RTC battery 438556-001 Before removing the RTC battery, follow these steps: 48 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system.
Remove the RTC battery: ▲ Use a non-conductive, flat-bladed tool to pry the RTC battery out of the socket. Reverse this procedure to install the RTC battery. Be sure the RTC battery is installed with the “+” sign facing up. Fan assembly Description Spare part number Fan assembly 438528-001 Before removing the fan assembly, follow these steps: ENWW 1. Shut down the computer.
Remove the fan assembly: 1. Disconnect the fan cable (1) from the system board. 2. Remove the Phillips PM2.0×9.0 screw (2) that secures the fan assembly to the top cover. 3. Remove the fan assembly (3). Reverse this procedure to install the fan assembly. NOTE To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left and right sides of the computer. The computer uses an electric fan for ventilation.
4. Remove the battery (see Battery on page 28). 5. Remove the following components: a. Hard drive (see Hard drive on page 29) b. Memory/Mini PCI card module compartment cover (see Memory module on page 31) c. Optical drive (see Optical drive on page 35) d. Switch cover (see Switch cover on page 37) e. Keyboard (see Keyboard on page 39) f. Display assembly (see Display assembly on page 41) g. Base enclosure (see Base enclosure on page 46) h.
3. Lift the left side of the heat sink (3) and remove it. NOTE The thermal paste should be thoroughly cleaned from the surfaces of the processor (1) and heat sink (2) each time the heat sink is removed. Thermal paste is included with all heat sink and processor spare part kits. Reverse this procedure to install the heat sink.
Processor NOTE All processor spare part kits include thermal paste. Description Spare part number Intel Pentium M 740 1.73-GHz processor 438555-001 Intel Celeron M 360 1.40-GHz processor 438554-001 Intel Celeron M 350 1.30-GHz processor 438553-001 Before removing the processor, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2.
2. Lift the processor (2) straight up and remove it. NOTE The gold triangle (3) on the processor should be aligned with the triangle (4) embossed on the processor socket when you install the processor. Reverse this procedure to install the processor.
Speaker Description Spare part number Speaker 438559-001 Before removing the speaker, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. 4. Remove the battery (see Battery on page 28). 5. Remove the following components: a. Hard drive (see Hard drive on page 29) b.
System board Description Spare part number 915GM for use only with computer models with wireless LAN capability 438521-001 910GML for use only with computer models with wireless LAN capability 438520-001 910GML for use only with computer models without wireless LAN capability 438519-001 When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory module (see Memory module on page 31) ● Mi
Remove the system board: 1. Remove the Phillips PM2.0×3.0 screw that secures the system board to the top cover . 2. Use the optical drive connector (1) to lift the left side of the system board (2) until it rests at an angle. 3. Flex the right side of the top cover (3) until the external monitor connector clears the opening in the top cover. 4. Slide the system board (4) away from the top cover at an angle until it clears the top cover Reverse this procedures to install the system board.
PC Card assembly Description Spare part number PC Card assembly 438551-001 PC Card slot bezel 438527-001 Before removing the PC Card assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. 4. Remove the battery (see Battery on page 28). 5.
2. Remove the two Phillips PM2.0×3.0 screws that secure the PC Card assembly to the system board. 3. Turn the system board top-side up with the PC Card eject button toward you. 4. Disengage the slots on the PC Card assembly from the tabs (1) on the PC Card connector. Remove the PC Card assembly from the system board. Reverse this procedure to install the PC Card assembly.
TouchPad cable Description Spare part number TouchPad cable 438551-001 Before removing the TouchPad cable, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord. 4. Remove the battery (see Battery on page 28). 5. Remove the following components: a.
2. Release the ZIF connector (1) to which the TouchPad cable is connected and disconnect the TouchPad cable (2) from the TouchPad board. Reverse this procedure to install the TouchPad cable.
6 Computer Setup WARNING! Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard.
Your preferences go into effect when the computer restarts. Computer Setup defaults To return all settings in Computer Setup to the values that were set at the factory: 1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen. In Computer Setup, the following shortcuts are available: ● To change the language, press f2. ● To view navigation information, press f1.
Computer Setup menus The menu tables in this section provide an overview of Computer Setup options. NOTE Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File Menu Select To Do This System information ● View identification information for the computer and the batteries in the system. ● View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version.
Select To Do This System IDs Enter user-defined computer asset and ownership tag. Disk Sanitizer Run Disk Sanitizer to destroy all existing data on the primary hard drive. The following options are available: ● Fast: Runs the Disk Sanitizer erase cycle once. ● Optimum: Runs the Disk Sanitizer erase cycle 3 times. ● Custom: Allows you to select the desired number of Disk Sanitizer erase cycles from a list.
Select To Do This port to the computer or to an optional docking device (select models only). Built-in Device Options Port Options ● Automatic/disable Intel SpeedStep Technology. ● Select a parallel port mode: EPP (Enhanced Parallel Port), standard, bidirectional, or ECP (Enhanced Capabilities Port). ● Enable/disable BIOS DMA data transfers (select models only) ● Enable/disable the system fan when connected to an AC outlet. ● Enable/disable Intel or AMD PSAE Execution Disable.
7 Specifications Computer specifications Metric U.S. Height (front to back) 3.01 to 3.41 cm 1.18 to 1.34 in Width 33.39 cm 13.19 in Depth 24.68 cm 9.75 in Weight (with optical drive, hard drive, and battery) 2.48 kg 5.47 lbs Dimensions Input power Operating voltage 18.5 V dc @ 3.5 A – 65 W Operating current 3.
Metric Nonoperating U.S. 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate NOTE Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures.
14.1-inch, WXGA display specifications Metric U.S. Height 21.4 cm 8.4 in Width 28.6 cm 11.2 in Diagonal 35.7 cm 14.1 in Number of colors Up to 16.8 million Contrast ratio 300:1 (typical) Brightness 200 nits (typical) Dimensions Pixel resolution ENWW Pitch 0.237 × 0.237 mm Format 1024 × 768 Configuration RGB stripe Backlight CCFL Refresh rate 60 Hz PPI 107 Viewing angle +/-45° horizontal, +/-25° vertical (typical) 14.
14.0-inch, WXGA display specifications Metric U.S. Dimensions Height 8.3 in Width 11.1 in Diagonal 14.0 in Number of colors Up to 16.8 million Contrast ratio 300:1 (typical) Brightness 200 nits (typical) Pixel resolution 70 Pitch 0.237 × 0.
Hard drive specifications 60-GB* 40-GB* Height 9.5 mm 9.
Primary 4-cell, Li-ion battery specifications Metric U.S. Height 2.00 cm 0.79 in Width 26.80 cm 3.70 in Depth 5.30 cm 5.28 in Weight 0.34 kg 0.75 lb Dimensions Energy Voltage 14.4 V Amp-hour capacity 4.
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive specifications Applicable disc Center hole diameter Read: Write: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CDEXTRA, Portfolio, CD-R, CD-RW), CDR, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM CD-R and CD-RW DVD+R, DVD+RW, DVD-R, DVD-RW, DVD-RAM 1.5 cm (0.59 in) Disc diameter Standard disc 12 cm (4.
DVD±RW/R and CD-RW Double-Layer Combo Drive specifications Applicable disc Center hole diameter Read: Write: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CDEXTRA, Portfolio, CD-R, CD-RW), CDR, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM CD-R and CD-RW 1.5 cm (0.59 in) Disc diameter 74 Standard disc 12 cm (4.72 in) Mini disc 8 cm (3.15 in) Disc thickness 1.2 mm (0.
System DMA specifications Hardware DMA System function DMA0 Not applicable DMA1* Not applicable DMA2* Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5* Available for PC Card DMA6 Not assigned DMA7 Not assigned *PC Card controller can use DMA 1, 2, or 5.
System interrupt specifications Hardware IRQ System function IRQ0 System timer IRQ1 Standard 101-/102-Key or Microsoft Natural Keyboard IRQ2 Cascaded IRQ3 Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9* Microsoft ACPI-compliant system IRQ10* Intel USB UHCI controller—24C2 Intel 82852/82855 GM/GME
System I/O address specifications ENWW I/O address (hex) System function (shipping configuration) 000 - 00F DMA controller no. 1 010 - 01F Unused 020 - 021 Interrupt controller no.
78 I/O address (hex) System function (shipping configuration) 220 - 22F Entertainment audio 230 - 26D Unused 26E - 26 Unused 278 - 27F Unused 280 - 2AB Unused 2A0 - 2A7 Unused 2A8 - 2E7 Unused 2E8 - 2EF Reserved serial port 2F0 - 2F7 Unused 2F8 - 2FF Infrared port 300 - 31F Unused 320 - 36F Unused 370 - 377 Secondary diskette drive controller 378 - 37F Parallel port (LPT1/default) 380 - 387 Unused 388 - 38B FM synthesizer—OPL3 38C - 3AF Unused 3B0 - 3BB VGA 3BC - 3BF
System memory map specifications ENWW Size Memory address System function 640 KB 00000000-0009FFFF Base memory 128 KB 000A0000-000BFFFF Video memory 48 KB 000C0000-000CBFFF Video BIOS 160 KB 000C8000-000E7FFF Unused 64 KB 000E8000-000FFFFF System BIOS 15 MB 00100000-00FFFFFF Extended memory 58 MB 04800000-07FFFFFF Super extended memory 58 MB 04800000-07FFFFFF Unused 2 MB 08000000-080FFFFF Video memory (direct access) 4 GB 08200000-FFFEFFFF Unused 64 KB FFFF0000-FFFFFFFF
8 Screw listing This section provides specification and reference information for the screws and screw locks used in the computer. All screws and screw locks listed in this section are available in the Screw Kit, spare part number 438558-001, and the Display Screw Kit, spare part number 438543-001.
Phillips PM2.5×8.0 captive screw Color Quantity Length Thread Head width Black 3 8.0 mm 2.5 mm 5.0 mm Where used: (1) Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C clips) (2) One screw that secures the memory/Mini PCI card module compartment cover to the computer (screw is captured on the cover by a C clip) ENWW Phillips PM2.5×8.
Phillips PM3.0×3.0 screw Color Quantity Length Thread Head width Silver 4 3.0 mm 3.0 mm 5.
Phillips PM2.0×9.0 screw Color Quantity Length Thread Head width Black 20 9.0 mm 2.0 mm 5.0 mm Where used: (1) One screw that secures the optical drive to the computer (2) Five screws that secure the switch cover to the computer (3) Two screws that secure the keyboard to the computer Where used: 2 screws that secure the display assembly to the computer ENWW Phillips PM2.0×9.
Where used: One screw that secures the base enclosure to the computer Where used: 7 screws that secure the base enclosure to the computer Where used: (1) One screw that secures the fan assembly to the computer (2) One screw that secures the speaker to the computer 84 Chapter 8 Screw listing ENWW
ENWW Phillips PM2.0×9.
Phillips PM2.0×3.0 screw Color Quantity Length Thread Head width Silver 9 3.0 mm 2.0 mm 4.
Where used: One screw that secures the system board to the base enclosure Where used: 2 screws that secure the PC Card assembly to the system board ENWW Phillips PM2.0×3.
Phillips PM2.0×7.0 screw Color Quantity Length Thread Head width Black 2 7.0 mm 2.0 mm 5.
Phillips PM2.5×6.0 screw Color Quantity Length Thread Head width Silver 17 6.0 mm 2.5 mm 5.0 mm Where used: 8 screws that secure the display bezel to the display assembly Where used: One screw that secures the display inverter to the display enclosure Where used: 4 screws that secure the display panel to the display enclosure ENWW Phillips PM2.5×6.
Where used: 4 screws that secure the heat sink to the base enclosure 90 Chapter 8 Screw listing ENWW
9 Backup and recovery Backup HP Backup and Recovery Manager provides several ways to back up the system and to recover optimal system functionality. NOTE HP installed drivers, utilities, and applications can be copied to a CD or to a DVD using HP Backup and Recovery Manager. NOTE Formatted DVD±RW discs and DVD±RW double-layer discs are not compatible with HP Backup and Recovery Manager. NOTE The computer must be connected to external power before you perform backup and recovery procedures.
3. Click Back up to protect system settings and important data files, and then click Next. 4. Click Back up individual files and folders, and then click Next. 5. The Backup Wizard opens. 6. Click Next. 7. Click Backup selected files from most common locations (Recommended). - or Click Advanced Backup (Experienced users) to access advanced filtering techniques. 8. Click Next. 9. Follow the on-screen instructions.
Backing up modifications made to the system When you back up modifications since your last backup, you are creating system recovery points. This allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system. NOTE The first system recovery point, a snapshot of the entire image, is automatically created the first time you perform a backup.
NOTE Before using HP Backup and Recovery Manager, try repairing the system by running Windows System Restore. For more information, select Start > Help and Support, and then search for “System Restore.” HP Backup and Recovery Manager performs these tasks: ● Creating recovery discs (highly recommended)—The recovery discs are used to start up your computer and to recover the full factory image (operating system and software) in case of system failure or instability.
5. Click Write to CD/DVD, and then click Next. 6. Follow the on-screen instructions. Performing a recovery Performing a recovery from the recovery discs Follow these steps to perform a recovery from the recovery discs: 1. Back up all personal files. 2. Insert the first recovery disc into the optical drive and restart the computer. 3. Follow the on-screen instructions. Performing a recovery from the hard drive There are two ways to initiate a recovery from the hard drive: ● From within Windows.
10 Connector pin assignments Audio-out (headphone) Pin Signal 1 Audio out, left channel 2 Audio out, right channel 3 Ground Audio-in (microphone) 96 Pin Signal 1 Audio signal in 2 Audio signal in 3 Ground Chapter 10 Connector pin assignments Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
External monitor ENWW Pin Signal 1 Red analog 2 Green analog 3 Blue analog 4 Not connected 5 Ground 6 Ground analog 7 Ground analog 8 Ground analog 9 +5 VDC 10 Ground 11 Monitor detect 12 DDC 2B data 13 Horizontal sync 14 Vertical sync 15 DDC 2B clock External monitor 97
RJ-11 (modem) Pin Signal 1 Unused 2 Tip 3 Ring 4 Unused 5 Unused 6 Unused RJ-45 (network) 98 Pin Signal 1 Transmit + 2 Transmit - 3 Receive + 4 Unused 5 Unused 6 Receive - 7 Unused 8 Unused Chapter 10 Connector pin assignments ENWW
Universal Serial Bus ENWW Pin Signal 1 +5 VDC 2 Data - 3 Data + 4 Ground Universal Serial Bus 99
11 Power cord set requirements The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The 3-conductor power cord set included with the computer meets the requirements for use in the country where the equipment is purchased. Power cord sets for use in other countries must meet the requirements of the country where the computer is used. Requirements for all countries The requirements listed below are applicable to all countries.
Requirements for specific countries ENWW Country/region Accredited agency Applicable note number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 Korea EK 4 The Netherlands KEMA 1 Norway NEMKO 1 The People's Republic of China CCC 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1.
12 Recycling Battery When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.
Display WARNING! The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. CAUTION The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling should be exercised when removing these components. NOTE Materials Disposal.
Perform the following steps to disassemble the display assembly: 1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. 2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel (3).
ENWW 4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). 5. Remove all screws (1) that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly (2) from the display enclosure. 7. Turn the display panel assembly upside down. 8. Remove all screws that secure the display panel frame to the display panel. 9.
10. Remove the display panel frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover (2) and swing it forward. 13. Remove the backlight cover. 14. Turn the display panel right-side up.
15. Remove the backlight cables (1) from the clip (2) in the display panel. 16. Turn the display panel upside down. 17. Remove the backlight frame from the display panel. WARNING! The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury.
18. Slide the backlight out of the backlight frame. 19. Disconnect the display cable (1) from the LCD panel. 20. Remove the screws (2) that secure the LCD panel to the display rear panel. 21. Release the LCD panel (3) from the display rear panel. 22. Release the tape (4) that secures the LCD panel to the display rear panel. 23. Remove the LCD panel. 24. Recycle the LCD panel and backlight.
Index A AC adapter, spare part number 19, 20 antennae disconnecting 34 illustrated 16 location 7 spare part number 16, 20 applications key, Windows 5 audio, product description 2 audio-in jack location 7 pin assignments 96 audio-out jack location 7 pin assignments 96 B backup 91 base enclosure removal 46 spare part number 15, 20, 46 battery removal 28 spare part number 15, 20, 28 specifications 72 battery bay 10 battery light 7 battery release latch 10 bezel illustrated 16 removal 43 spare part numbers 16,
display panel illustrated 16 removal 44 spare part numbers 16, 21, 44 Display Screw Cover Kit, spare part number 16, 21 Display Screw Kit, spare part number 16, 21 display specifications 69, 70 display switch 6 docking support, product description 3 drives, boot order 65 drives, preventing damage 24 DVD±RW and CD-RW Super Multi Double-Layer Combo Drive precautions 24 removal 35 spare part number 15, 18, 20, 35 specifications 73 DVD±RW/R and CD-RW DoubleLayer Combo Drive precautions 24 removal 35 spare part
O operating system, product description 3 optical drive location 8 precautions 24 product description 2 removal 35 spare part numbers 15, 18, 35 specifications 73, 74 optical drive bracket, removal 36 P packing guidelines 25 panels, product description 1 parallel port mode 66 password clearing 11 passwords 64 PC Card assembly removal 58 spare part number 14, 22, 58 PC Card eject button 9 PC Card slot 9 PC Card slot bezel, spare part number 14, 21, 58 plastic parts 23 Plastics/Hardware Kit contents 17 spare
system DMA 75 system fan 66 system information 64 system memory map 79 T thermal paste, replacement 52 tools required 23 top components 6 top cover, spare part number 14, 20 TouchPad 4 TouchPad cable removal 60 spare part number 60 TouchPad cable, spare part number 14, 22 TouchPad left button 4 TouchPad right button 4 TouchPad scroll zone 4 transporting guidelines 25 U Universal Serial Bus (USB) port location 9 pin assignments 99 unknown password 11 USB legacy support 65 V vents 9, 10 W Windows applications
