Installation & Assembly

ManualsBrandsHouse of Hampton ManualsAll Ceiling Fans52" Noyes 5 -Blade Crystal Ceiling Fan with Remote Control and Light Kit Included

Installation Guide

You may install your ceiling fan as a flush mount, or you may use the provided down rod. Measure your room

height before installing the fan and consider the different installation height options indicated in the above

diagram.

Table of Contents:

Safety tips Pg.2 Wiring Pg.7 -

Unpacking your fan Pg.3 Canopy Assembly Pg.8

Tools and material required Pg.4 Blade Assembly Pg.9

Outlet Box Pg.4-5 Light Kit and Shade Assembly Pg.10

Hanging Bracket Installation Pg.4 -

Trouble Shooting Pg.11

Fan Assembly (Flush Mount) Pg.6 Maintenance Pg.11

Fan Assembly (w/down rod) Pg.

Shade/Jewel Assembly Pg. 12

Professional Installation Recommended

Note: Approximate time of assembly is 30 min to 1 hour

PAGE 1

READ AND SAVE THESE

INSTRUCTIONS

Summary of content (12 pages)

PAGE 1
Installation Guide READ AND SAVE THESE INSTRUCTIONS You may install your ceiling fan as a flush mount, or you may use the provided down rod. Measure your room height before installing the fan and consider the different installation height options indicated in the above diagram. Table of Contents: Safety tips Pg.2 Unpacking your fan Pg.3 Tools and material required Pg.4 Outlet Box Pg.4-5 Wiring Pg.7 - 8 Canopy Assembly Pg.8 Blade Assembly Pg.9 Light Kit and Shade Assembly Pg.
PAGE 2
SAFETY TIPS WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
PAGE 3
1. Unpacking Your Fan. Carefully open the packaging. Remove items from styrofoam inserts. Remove motor housing and place on carpet or styrofoam to avoid damage to finish. Do not discard fan carton or styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory.
PAGE 4
3. Tools Required •Step ladder •Pliers •Screw driver flat head and phillip •Electrical tape •Circuit tester 4. Installation Preparation To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7ft.(2.13m) from the floor and 30in.(76cm) from any wall or obstruction. The fan is suitable for room sizes up to 400 square feet (37.2square meters). This fan can be mounted with a down rod on a normal or vaulted ceiling. Down rod is included, 6” length.
PAGE 5
CAUTION: Be sure outlet box is grounded properly and that a ground wire (green or bare) is present. Partially loosen screws in slotted holes of canopy. Remove the other 2 screws (along with the star washers) -save for later use. Twist canopy to remove hanging bracket. Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box. If installing on a vaulted ceiling, face opening of Hanging Bracket towards high point of ceiling.
PAGE 6
. Flush Mount Assembly. Go to step 7 if assembling with down rod. • Remove round rubber ring from the Canopy • Thread the electrical wires through the canopy. • Remove every other screw on the motor housing total of 3 screws. WARNING – Ensure you only remove every other screw, others must remain firmly tightened. • Attach the canopy to the motor housing securely with the 3 screws previously removed. Tighten firmly. • Continue to step 8 for wiring.
PAGE 7
. Fan Assembly with Down Rod Remove Pin and Clip from down rod (if you have not already done so). Slide the Down rod through the canopy, and the Down rod cover as shown. Thread the electrical wires through down rod and pull extra wire slack from the upper end of the down rod. Tip: Apply small piece of electrical tape to the ends of the electrical wires to keep them together when threading them through the down rod. Loosen the Yoke set screw.
PAGE 8
3. Install the receiver into the Hanging bracket of the fan. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. Do not install in damp locations or immerse in water. For indoor use only. Do not pull on or cut the receiver wire leads shorter. 4. Proceed making the wire connections following this diagram carefully. CAUTION: Incorrect wire connection would damage the receiver. Be sure outlet box is properly grounded or that a ground wire (GREEN or bare) is present.
PAGE 9
Important: Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring, or if the house/building wires are different colors than those referred to in the instructions, please use a qualified electrician. 9.Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. Locate 15 blade attachment screws and washers in one of the hardware packs.
PAGE 10
.Light Kit Assembly. 1. Remove the three screws from the Light kit. 2. Plug the connectors from the Light kit to the connectors from the Switch housing. Please note the correct wiring is: •White to White • Black to Blue 3.Gently push the connectors into switch housing and align the holes in the Light kit with holes in the Switch housing. Secure the light kit with the 3 screws that were previously removed. Attach the Shade to the Light kit using the Finial you will find installed on the Light kit pipe.
PAGE 11
Ceiling Fan Troubleshooting Guide Welcome to the family! We’re honored you’ve decided to include one of our ceiling fans in your home. Problem Solution Fan/Lights do not start • Check all fuses/circuit breakers • Turn off electrical power and ensure the wiring is correct • Confirm that the remote/receiver dip switches are correctly synced • Check batteries in remote • Ensure the motor/lights are set to an “On” setting via the pull chains Fan is noisy • Allow a 24-hour “break in” period.
PAGE 12
11. Shade Crystal Assembly This item contains beautiful hanging crystals that are to be installed on your shade, adding a lovely ambience to your item and room. To install, simply follow these steps. 1. Identify the (A) and (B) crystals contained in your item packaging and place aside a. Crystal (A) – 12 pcs b. Crystal (B) – 7 pcs 2. Following the diagram below, use the attached hook on the crystals and secure the seven (7) (B) crystals to the inner ring of the shade 3.