Installation Instructions

CLEARANCES:
• When installed into a
corner, allow 2” min.
clearance between
dishwasher and adjacent
cabinet, wall or other
appliances.
• Allow 27” min. clearance
from the front of the
dishwasher for door
opening.
3
Countertop
27"
Dishwasher
Clearance for Door
Opening 2” Minimum
Installation Preparation
To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher
is completely enclosed at the time of installation.
WARNING
Para reducir el riesgo de
descarga eléctrica, incendio
o lesiones a personas, el instalador debe asegurarse
de que el lavaplatos esté completamente cerrado en
el momento de la instalación.
ADVERTENCIA
PREPARE DISHWASHER ENCLOSURE
Built-In Models Only: Spacemaker
®
Models Only:
• The rough cabinet opening must be at least 24” deep,
24” wide and approximately 34-1/2” ± 1/4” high from
floor to underside of the countertop.
• The dishwasher must be installed so that drain hose is
no more than 10’ in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides
and back, and must not support any part of the enclosure.
• The back wall should be free of pipes or wires.
• Adjacent cabinets should be square and plumb to
ensure a good fit.
• Make sure the floor is level inside the opening and
even with the finished floor of the kitchen. This will
facilitate removal of the dishwasher at a later date for
service, if needed.
Min.
Min.
• The rough cabinet opening must be at least 24” deep,
24” wide and approximately 34-1/4” ± 1/4” height.
• This dishwasher fits under a special sink with a depth
of 6” or less in a 1-1/2” countertop.
• The dishwasher must be installed so that drain hose is
no more than 10’ in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides
and back, and must not support any part of the enclosure.
• The back wall should be free of pipes or wires.
• Water line to
sink faucet
and drain from
sink can be run
through Area
“A.”
• Hot water line
to dishwasher
is installed in
Area “B.”
• Garbage
disposer, water
lines to faucet,
waste trap, air
gap and water
shut-off valve
are installed in
a 12” wide cabinet, Area “C”.
• Sink opening for garbage disposer must be dimensioned
as shown (7-1/2”) in Area “C.” This will provide clearance
for disposer and plumbing in Area “C” when using either
single or double bowl sink.
• Adjacent cabinets should be square and plumb to
ensure a good fit.
NOTE: A gap between the dishwasher tub front flange and
the front of the base cabinet may result due to either the
cabinet being less than 24” deep or the sink bowl not being
installed to specifications. If the gap is more than 3/4”, the
sink bowl must be relocated to meet specified dimensions.
Cabinet Side
Adjacent to Dishwasher
Sink
Installation
Cutout
8" X 20"
Adjacent Cabinet
Rear Cutout
12"
3-1/4"
12-1/2"
24”
min
24” min
5"
C
5"
7-1/2"
7-1/2"
Dishwasher
Side View
11-3/4" Max.
Plumbing
4"
Max.
34-1/4"
1/4"
+
_
10-1/4" MA .
PLUMBING
DEPTH
1" Max. To
Sink Flange
20-1/2" Max.
Sink Bowl
11" Min.
Drain
6" Max.
3/4" Min.
1-1/4"
1-1/2"
Close Elbow
Min. I.R.
24" Min.
Cabinet
Wall
B
A
X