HOROW INSTALLATION INSTRUCTIONS FOR SHOWER DOOR AND BATHTUB DOOR TE SERIES TE-���� CH/BN/MB TE SHOWER AND TUB DOOR MANUAL TE-���� CH/BN/MB ����.V �.
Note: Stainless steel top rail can be trimmed up to �”for width adjustment. If installation opening is smaller, the overlap of two glass panel is bigger, and the entrance size is reduced accordingly. 1/4" 1/8" Silicone Level Mallot Drill Pencil Tape Measurer Drill Bit Screwdriver （Phillips） Allen Wrenches Sealant Finishing Tool Painters Tape Tips: Measure the finished opening before proceeding with the instalation to be sure that the correct model size has been ordered.
PARTS LIST A FOR SHOWER/BATHTUB DOOR (�MM) 14 13 12 2 12 15 16 17 11 19 1 3 18 4 6 7 9 5 8 10 Keep small parts away from children PACKING LIST 1pc Wall Plugs 6pcs Handle Wall Jamb 1pc Square Wall Joints Whit Plastic Bumper x 2 Screws ST4x1 3/8" 6pcs Screws ST5x1 3/8" x 4 Fixed Panel 1pc Wall Plugs x 4 Door Panel 1pc 5/8" Plastic Bumper 1pc Top Rail 1pc Glass Fixing Piece 2pcs 16 Roller 2sets Bottom Guide x 1 Screws ST5x1 3/8" x 2 1set Wall Plugs x 2 2set Gasket-A
PARTS LIST B FOR SHOWER/BATHTUB DOOR (��MM) 14 13 12 2 12 15 16 17 11 18 1 3 4 6 7 9 5 8 10 Keep small parts away from children PACKING LIST 1pc Wall Plugs 6pcs Handle Wall Jamb 1pc Square Wall Joints Whit Plastic Bumper x 2 Screws ST4x1 3/8" 6pcs Screws ST5x1 3/8" x 4 Fixed Panel 1pc Wall Plugs x 4 Door Panel 1pc 5/8" Plastic Bumper 1pc Top Rail 1pc Glass Fixing Piece 2pcs 16 Roller 2sets Bottom Guide x 1 Screws ST5x1 3/8" x 2 1set Wall Plugs x 2 2set Gasket-A for
INSTALLATION STEPS STEP �A ±0.0 ±0.0 Open Width XXX Threshold must be level Wall must be plumb TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP �B Model Width - Finished Opening(Width) = Cut Off Length Finished Opening （Width） Cut Off Length �� �/�”-��” �� �/�”-��” �” �” �� �/�”-��” �� �/�”-��” �” ��” �” *This Shower Door Can Be Installed At Wall Opening From �� �/�” to ��” (No Need Cut Rail). A 14 A When cutting top rail, cut off from the end without the hole. B 8 B Measure the drip rail with a tape measure. Cut the length according to installer's recommendation. TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP � FINDING CENTERLINE OF CURB. A CE NT ER LIN E B A CE NT ER E IN RL TE N CE LIN E B TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP � 2 A 2 A 1/4" 1 2 3 B Screw ST4x1 3/8" 8 B 1 1/4" TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP � A 8 B 5 Roller C 16 A 8 2 3 B Screw ST4x1 3/8" 2 C 18 4 4 8 18 Special for �mm glass installation, No need the seals for ��mm glass. TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP � A: Installation size width less than ��", use �/�" plastic bumper as shown. 1/4" PLASTIC BUMPER 1/4" 1/4" PLASTIC BUMPER 1/4" B: Installation size up to ��", use �/�" plastic bumper on fixed panel side as shown. 5/8" PLASTIC BUMPER 5/8" TE SHOWER AND TUB DOOR MANUAL 1/4" PLASTIC BUMPER 1/4" ����.V �.
INSTALLATION STEPS STEP � Adjust top rail until it level. 12 14 A B2 See Table For Dimension B1 12 12 3/8" B See Table For Dimension 5/16" C C B See Table For Dimension (From Wall Bracket Core To Bottom) 5/16" Screw ST5x1 3/8" 14 12 Table Shower Height ��” ��” TE SHOWER AND TUB DOOR MANUAL Screw ST5x1 3/8" 14 12 C 15 Wall Bracket Core Height ��-�/��” ��-�/��” ����.V �.
INSTALLATION STEPS STEP � FOR �MM GLASS A 4 A 6 5/16" TE SHOWER AND TUB DOOR MANUAL 6 ����.V �.
INSTALLATION STEPS STEP � FOR ��MM GLASS A Bottom Guide Install Ovewiew ��MM GLASS 6 10 10 8 6 8 �MM GLASS This bottom guide is pre-installed for �mm glass.To install ��mm glass, please take out the plastic insert block, install the insert block according to the marked position as shown on diagram before going to next step. B 4 B 6 5/16" TE SHOWER AND TUB DOOR MANUAL 6 ����.V �.
INSTALLATION STEPS STEP � 16 A A 5 B 6 B TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP � A 17 A A TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP �� Carefully slide the door toward the wall and check the door is sliding smoothly. Adjust if necessary using offset in rollers, so that the sliding door is parallel to the tray. A 5 Roller A 16 INSIDE OF SHOWER A HOW TO ADJUST Step � : Loosen center bolt with hex wrench Step � : Rotate to adjust panel angle with hex wrench Step � : Tighten center bolt 9 B TE SHOWER AND TUB DOOR MANUAL B ����.V �.
INSTALLATION STEPS STEP �� 11 A C B B 10 5 A C 7 5 Please note to get correct gascket seals for different glass thick configuration. TE SHOWER AND TUB DOOR MANUAL ����.V �.
INSTALLATION STEPS STEP �� �� HOURS Apply clear silicone caulking along the wall and threshold of the shower door inside and outside. (make sure you ) wait ��hours before using the shower. Do not allow water to directly hit door. �� HOURS TE SHOWER AND TUB DOOR MANUAL ����.V �.
