Thermostat - Regulator User Manual

ManualsBrandsHoneywell ManualsDesktopTH110-DP-P

08161 / TH110-DP-P / TL8230 69-2023 1/11/06 2/2

Programmable Thermostat - Installation and User Guide

Automatic - The temperature is set according to the energy-saving

schedule. To place the thermostat in this mode, press Mode until is dis-

played. The icons of the current period and preset temperature are also dis-

played.

Temporary Bypass: If you modify the setpoint (by pressing the , ,

or button) when the thermostat is in automatic mode, the new set-

point will be used until the end of the current period. When the next

period starts, the temperature set for that period becomes the new set-

point.

Manual - The energy-saving schedule is not used. The temperature must

be set manually. To place the thermostat in this mode:

n Press Mode until is displayed.

o Set the temperature using the , , or button.

Vacation - The thermostat is set to the Vacation temperature. Press both

and buttons simultaneously to place the thermostat in Vacation mode.

The schedule consists of 4 periods per day which represents a typical week

day. You can program the thermostat to skip the periods that do not apply to

your situation. For example, you can skip periods 2 and 3 for the weekend.

The Comfort ( ) temperature is used in periods 1 and 3 and the Economy

( ) temperature is used in periods 2 and 4. For example, when the period

changes from 1 to 2, the setpoint automatically changes from Comfort setting

( ) to Economy setting ( ).

You can have a different program for each day of the week; i.e., each period

can start at different time for each day of the week. The thermostat has been

programmed with the following schedule.

To modify the schedule:

n Press Pgm to access the programming mode. Period 1 is selected.

o Press Day to select the day to program (hold for 3 seconds to select the

entire week).

p Press Hour and Min to set the start time of the selected period, or press

Clear if you want to skip the period (--:-- is displayed).

q Press Pgm to select another period, or press Day to select another day.

Then repeat step 3.

r Press Mode to exit the programming mode.

NOTE: If no button is pressed for 60 seconds, the thermostat will automati-

cally exit the programming mode.

Power: 208/240 Vac, 60 Hz

Maximum load: 16 A maximum (resistive only)

3328 watts @ 208 Vac

3840 watts @ 240 Vac

Display range: 32 °F to 140 °F (0 °C to 60 °C)

Display resolution: 0.1 °F (0.1 °C)

Setpoint range: 40 °F to 86 °F (5 °C to 30 °C)

Setpoint interval: 1 °F (1 °C)

Storage: -4 °F to 120 °F (-20 °C to 50 °C)

Certifications: CSA/UL

Data backup: In the event of a power outage, most settings are saved. Only the

time must be re-adjusted if the power outage lasts more than 2 hours. The thermo-

stat will return to the mode that was active prior to the power outage.

Honeywell warrants this product, excluding battery, to be free from defects in the work-

manship or materials, under normal use and service, for a period of one (1) year from the

date of purchase by the consumer. If at any time during the warranty period the product is

determined to be defective or malfunctions, Honeywell shall repair or replace it (at Hon-

eywell's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which

you purchased it, or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the

determination whether the product should be returned to the following address:

Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley,

MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not

apply if it is shown by Honeywell that the defect or malfunction was caused by damage

which occurred while the product was in the possession of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product within the terms

stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF

ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states

do not allow the exclusion or limitation of incidental or consequential damages, so this

limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON

THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-

POSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary

from state to state.

If you have any questions concerning this warranty, please write Honeywell Customer

Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Can-

ada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic

Drive, Scarborough, Ontario M1V4Z9.

If you have any questions about the operation of your thermostat, please go to

http://yourhome.honeywell.com, or call Honeywell Customer Care toll-free at 1-

800-468-1502.

Operating Modes

Energy-saving Schedule

Period Description Associated preset temperature

Wake-up

Away from home

Return home

Sleep

Period Setting

MO TU WE TH FR SA SU

6:00

8:00

--:-- --:--

6:00

--:-- --:--

10:00

Troubleshooting

Problems Solutions

The thermostat’s screen is blank. The thermostat’s switch is set to Off.

LO is displayed.

The measured temperature is below the

display range. Heating is activated.

HI is displayed.

The measured temperature is above the

display range.

The wrong time is displayed.

The thermostat was without power for

more than 2 hours.

The measured temperature is wrong.

The thermostat is located in a spot

exposed to an air draft.

The heater is always On. Check the thermostat wiring.

The thermostat indicates that heating is On

but the heater is not On.

Check the thermostat wiring.

The temperature does not change accord-

ing to the energy-saving schedule

Check that the thermostat is in Automatic

mode. Check also the energy-saving

schedule and clock settings.

Technical Specifications

;

Warranty

10.



Customer Assistance

11.

As an ENERGY STAR

partner, Honeywell has

determined that this product meets the E

NERGY STAR

guidelines for energy efficiency.

400-110-007-A_69-2023 (TH110A-DP-240 Cadet TL8230) ENG.fm Page 2 Wednesday, November 1, 2006 8:48 AM