User Manual
Table Of Contents
- PX940
- Table of Contents
- Customer Support
- Get Started
- Set Up the Printer
- Connect the Printer
- Configure the Printer
- Printer Configuration Menus
- Configure the Printer from the Web Page
- Configure the Printer with Honeywell PrintSet 5
- Configure the Printer with Programming Commands
- Change Background Image for the Ready Screen
- Printer Profiles
- Save a Printer Profile from the Web Page
- Load a Printer Profile from the Web Page
- Save a Printer Profile from the Main Menu
- Load a Printer Profile from the Main Menu
- Load a Printer Profile Using Programming Commands
- Install a Configuration File from a USB Storage Device
- Export a Configuration File to a USB Storage Device
- Menu Shortcuts
- Customize the Printer Web Page
- About the Verifier
- Setting up the Verifier
- Verifier License
- Calibration
- Verifier Settings
- Verification Type
- Passing Grade
- Aperture
- Retries
- Verification Failure Action
- Save Failed Label Images
- Void Pattern
- Print Modes and Speed
- Barcode Symbologies Supported
- Barcode Orientations
- Barcode Size Supported
- Verification Length
- Maximum Number of Barcodes per Label
- Printing Behavior after Error Recovery
- Printing Behavior after Recovered from error above:
- Printing Errors
- Unsupported Barcode Behavior
- Verification Failed Error Handling
- Reporting and Statistics
- Report Formats
- Individual Report
- Barcode Information
- All Supported 1D Barcodes Overall Parameters
- 2D Barcode, Datamatrix Overall Parameters
- 1D barcode 10 line Profile Grading Parameters
- Summary Report
- Restore Default Verification Files
- Fingerprint Command
- Troubleshooting
- Maintenance
- Product Specifications
- Default Settings
- Print Labels with INPrint
- Accessory Installation Instructions
PX940 User Guide 97
Maintenance Alerts
To view these settings:
• From the printer Main Menu, select Settings > System Settings > Maintenance
Alerts.
• From the printer web page, click the Configure tab. Go to System Settings >
Maintenance Alerts.
Maintenance
Alerts Setting
Description Default
Odometer (User
Resettable)
Sets the length of media (in meters) that the printer prints
before the Odometer (User Resettable) alert is sent, if this
alert is configured. Unit of measurement is defined in the Unit
of Measure parameter. Range is 0 to 4294967295.
0
Odometer (Printer) Sets the length of media (in meters) that the printer prints
before the Odometer (Printer) alert is sent. Unit of
measurement is defined in the Unit of Measure parameter.
Range is 0 to 4294967295.
0
Odometer (Printhead) Sets the length of media (in meters) that the printer prints
before the Odometer (Current Printhead) alert is sent, if this
alert is configured. Unit of measurement is defined in the Unit
of Measure parameter. Range is 0 to 4294967295.
0
Replace Printhead Sets the length of media (in meters) that the printer prints
before the Replace Printhead alert is sent, if this alert is
configured. Unit of measurement is defined in the Unit of
Measure parameter. Range is 0 to 4294967295.
0
Clean Printhead Sets the length of media (in meters) that the printer prints
before the Clean Printhead alert is sent, if this alert is
configured. Unit of measurement is defined in the Unit of
Measure parameter. Range is 0 to 4294967295.
0
Faulty Dot Sets the number of faulty dots on the printhead before the
Faulty Dot alert is sent, if this alert is configured. Range is
0 to 4294967295.
0
Media Low Diameter Sets the minimum diameter of the media roll before the
Media Low alert is sent, if this alert is configured. Range is 0
to 200 mm.
0
Ribbon Low Diameter Sets the minimum diameter of the ribbon roll before the
Ribbon Low alert is sent, if this alert is configured. Range is 0
to 200 mm.
0
Memory Low Sets the minimum percentage of free RAM memory and/or
Flash memory before the Memory Low alert (if this alert is
configured) is sent. Unit is percentage.
0