Ld : ig BEEN x HEX HERD CORKSCREW. 272 Fig. 3. Normally Open Drive Ear Mounting. INSTALLATION GENERAL The: SKIMPY. Damper © Actuator: can: be installed perplexingly ors manically. Her Hare two mounting approaches standard and nonstandard: Tse nonstandard mounting: when standard: mounting is:net practical {e.g for extra clearance of: non-Honeywell dampness. Tina: require ordering additional pants; STANDARD MOUNTING EXTERNAL MOUNTING 1. See Figure d for mounting dissensions.
INTERNAL MOUNTING NORMALLY: CLOSED MOUNTING 1. Ses Figure: § for internal: mounting normally closed dimensions: 2. Check face plate position and adjust if necessary. {Fig 9). The face plate must be parallel 16 the back ‘of the mounting bracket: 40 Use ranch: Ali niche fo Loosen mounting: Setscrews on damper mounting clamp: (Fig, 9 ong tore Remove and discard shipping sup: 4: Loosen: face plate nut between mounting: bracket and fitness ink: Remove: clevis pin from: actuator push rod: 5.
2: Set data per 10/1 normal (Open position. {Connect damper push rod: to damper drive ear with Clovis Pin C: 11: Connect truss link to damper With mounting screw and tighten face plate pts; 12. Tighten setscrews on damper mounting ¢lamp, 13: Uo to PIPING section. MESH, 1 Fig 10: eternal Mounting Normally GEE Bae EAR (HEEL WITH 5 2 DAMPER) UNGULATE A SETSCREWS. OL CAMPSITE: SLIPWAYS) HOE OR INCH DRIVE BLADE. ike Open Dimensions in Inches (Millimeters).
USE THESE HOLES IF GERIATRIC TO DAMPER: 5 Install net hater io: face plate using: the wo levees en pins; washers; and clips from Step: as shown in bee ! Figure 16. NOTE: For MAOISM, efficacy feedback spring. 6. For offset shaft: installation, | Bend threaded rod COTTAR 88 required. Use 45: depress bonds with 5 maximum of S-meh (76mm) offset 7. Gut threaded rod Subbranches (127 mmy shorter then Face plate to damper axle distance as determined in Step:d.
DEFAULTER wT, Fig. 20; Alienate Top Mount Face plate Positioning, 8; Tighten bolts an transform: connected to voracious: push rod (Fig. 213. CAUTION See Figure? for proper crank bol tightening. 9, Use mounting braces as a template and ark foi mounting screw locations. 135: Secure mounting: bracket with four 14 x Turbine slotted titivated sheer metal screws provided. 11: Install bail joints on the crank arms.
Obtain the following pants: += End Kit 18753693001 (Fig: 22 and Table 1); ane for each installation sx Modular Kit: 15753692-001 (Fig. 23 and Table 2); one for each adjacent; vertical Jetport bark 2: Attach support: brackets from end kit and modular kii(s): to sides of damper frame, NOTE: Mounting holes in brackets: will match holes in the frame a1: ally one location. See Figures 28 and 26.
% pigging sine LTH RIVE Cal 1 1S Kiloliter SCREW. fire HEX NUT CLEVIS High HEX MEADE! 124 Lock WASHER £2) i POX A SCREW: (2) SUPPORT BRACKET. Fig. 23. Modular Bit Assembly. ‘Table 2. Modular Kit Parts. Qty. |" Part No: 2 620 2 [72802 27 1 B0s9SAB 14000644.002 14000672001 | 14000767.001 315439 MIA THT: 14000643.004 318321 14000168:366 15753688.001 15753675.001 15753674.
INVEIGH DAFTER AND. PUSHCHAIR EVENKI: {ONE FOR EACH. APPLICATION. MAN GALVANIZED STEEL PIE BLACKBIRD, LENGTH DETERMINED HY DAMPER WIDTH. HE NOT FURBISHED) GITE MODULAR IT SHOW HERE TO ILLUSTRATE MOUNTING PRINCIPLE. (BELONGS ON NEXT VERTICAL DAMPER MODULAR RIT {ONE FOR EACH VERTICES DAMPER vid RANK) BAG ADJACENT TO END KIT ¢ A BRACKET MOUNT IN ONLY PEACE ON DAME. 254 IN, MM) HOLE CENTERS TO FIT. OPERATOR KIT (OME FOR BRACKET APPEAR ORLY ONCE ON EVERY EACH ACTUATOR) DAMPER OR SECTION: NOTE MODULAR KIT LEFTY.
95-1282 A BRACKET MOUNTS IN ONLY PLACE OW. DUPER 2878 IN (70 MW) HOLE CENTERS TO FIT. BRACKET. APPEAR IRONMONGERY ON EVERY: DAMPER OR SECTION: Normally Open Damper: Institutionalization.
INTERNAL DAMPER FRAME MOUNTING Lie intimidation, normally closed damper airtime (Fg 27 obtrusion the following additional parts: So Ballpoint ‘and Adapter Assembly: 140042422 on 5 NEH Diameter: Pushed: 27520 (order to glen required) : Jock nut: and. remove. factory-installed push rod. 3. Uke 18-inch Allen wrench to loosen: mounting: SLOWS DR [damper Mounting Clamp jon. tin, Remove and discard shipping stop.
ACTUATOR CONVERTING If sandpiper activator fs ordered for minimal mounting bit internal mounting is impractical; ban the: proper: predator or covariant using ihe following procedures. CONVERTING INTERNALLY MOUNTED NORMALLY. OPEN ACTUATOR TO EXTERNAL MOUNTING 1: Obtain the flowing additional parts; Li Mounting Screw’ Assembly: 14004237-001 we External: Drive: Axle Hardware : Assembly: 14004313003 2: Remove all four Clovis ping (Fig. 30). 3. Loosen all four crank arm halts, “45 Soe but transform shaft and.
RECKONING SHOULD BE PHYSICALLY. LINKED SWATH SLAVING OPERATOR. MELT dle Fig. 33 MEOW Stave © MAOISM for Large Tamper Installations. POSITIONED ADJUSTMENT (MPS18A Only) NOTE: © Reviser that the positioned feedback spring ie nop Binding on the positioned support: “The: MPS IBA is shipped with one of the following feedback: Springs: FA00JOT2-001, 3 psi (ZL PAY, J4004013-001, 5 psi (33 Pay; of 14004014001, 10 ysl (60 kappa.
