Install Instructions

ManualsBrandsHoneywell ManualsGas and Oil Burner AccessoriesNema 4 Cover Assembly

Table Of Contents

PRODUCT DATA

65-0151-3

204718A,C Cover Assembly for

S7800 Keyboard Display Module

APPLICATION

The 204718A NEMA 4 Cover Assembly (provides NEMA 4

protection for the S7800 Keyboard Display Module when the

S7800 is mounted on a suitable panel).

The 204718C NEMA 4 Cover Assembly (provides NEMA 4

protection for the S7800 Keyboard Display Module when the

S7800 is mounted on a suitable panel) and also provides

reset of the 7800 Series device.

INSTALLATION

When Installing This Product…

1. Read these instructions carefully. Failure to follow them

could damage the control or cause a hazardous

condition.

2. Check the ratings in the instructions and on the control

to make sure the control is suitable for your application.

3. Installer must be a trained, experienced Flame

Safeguard service technician.

4. After installation is complete, check out control

operation as provided in these instructions.

WARNING

Electrical Shock Hazard.

Can cause severe injury, death or property

damage.

Disconnect power supply before beginning installation

to prevent electrical shock and equipment damage.

More than one disconnect may be involved.

When the S7800 Keyboard Display Module is already

mounted on a panel, place the 204718A,C Cover Assembly

over it and mark or drill starter holes for No. 6 by 1/2 in. sheet

metal screws or use full-sized template as shown in Fig. 2.

When the S7800 Keyboard Display Module is to be mounted

on a panel, position the S7800 in the desired location and

mark and cut an opening for the S7800 connector cable. Then

place the 204718 Cover Assembly over it and mark or drill

starter holes for No. 6 by 1/2 in. sheet metal screws or use a

full-sized template as shown in Fig. 2.

To install the S7800 in the 204718A,C NEMA 4 Cover

Assembly, proceed as follows:

204718A

204718C

Contents

Application ........................................................................ 1

Installation ........................................................................ 1

Ordering Information ........................................................ 2

Summary of content (4 pages)

PAGE 1
204718A,C Cover Assembly for S7800 Keyboard Display Module PRODUCT DATA INSTALLATION When Installing This Product… 204718A 1. 2. 3. 4. Read these instructions carefully. Failure to follow them could damage the control or cause a hazardous condition. Check the ratings in the instructions and on the control to make sure the control is suitable for your application. Installer must be a trained, experienced Flame Safeguard service technician.
PAGE 2
04718A,C COVER ASSEMBLY FOR S7800 KEYBOARD DISPLAY MODULE 1. 2. 3. 4. 5. Disconnect power supply to prevent electrical shock and/or equipment damage. Place the tabs on the bottom of the S7800 Keyboard Display Module into the slots below the scroll panel on the cover. See Fig. 1. Push the S7800 down into the slots while moving the top of the S7800 forward. The S7800 will snap into place at the top of the cover.
PAGE 3
1 4 (57) 2 1 4 (57) 2 3 1 (83) 4 3 1 (83) 4 5 (8) 16 5 16 (8) 204718A,C COVER ASSEMBLY FOR S7800 KEYBOARD DISPLAY MODULE M2836A Fig. 2. Full-sized mounting template for 204718 Cover Assembly in in. (mm).
PAGE 4
204718A,C COVER ASSEMBLY FOR S7800 KEYBOARD DISPLAY MODULE Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 customer.honeywell.com ® U.S. Registered Trademark © 2007 Honeywell International Inc. 65-0151—3 M.S. Rev.