Hedge Trimmer Attachment SSHH Click to Save As Instruction Manual Contents Important Information····················· 2 1. Safety···································· 4 1.1 1.2 1.3 1.4 1.5 1.6 Warnings········································ 4 General Precautions························· 6 Safety Devices and Protective Guard······· 11 Protective Equipment······················ 12 Noise··········································· 12 Vibration······································· 12 2.
Important Information Intended Purpose This product (hereinafter referred to as an attachment) is designed to be attached to an approved powerhead (to be purchased separately) for cutting hedges. (Refer to page 16 for approved powerheads.) Do not use the hedge trimmer for any other purpose or in any other way.
Important Cautions for Safe Work ●● NIKKARI Co., Ltd. (hereinafter referred to as NIKKARI) cannot foresee all the risks in handling the hedge trimmer. Therefore, also give consideration to general safety measures not stated in this manual, powerhead manual to prevent injuries when handling the hedge trimmer. ●● The hedge trimmer is a high-speed cutting tool with very long reach. To decrease risk of personal injury, special safety precautions must be observed.
1. Safety California Proposition 65 This product contains or emits chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 1.1 Warnings For appropriate use of the hedge trimmer, follow the instructions in this manual. Warning labels are attached to places where there are potential risks or in the periphery. The warning labels in this instruction manual are categorized depending on the degree of risk as shown in the table below. 1.1.
1.1.2 Warning Labels Cautions for Handling (a) This hedge trimmer is provided with warning labels to indicate important cautions. Understand the meanings of the warning labels thoroughly to work in a safe environment . (b) Do not operate the hedge trimmer until you have a good understanding of the meanings of the warning labels. If you do not understand the meanings, contact your servicing dealer.
1.2 General Precautions 1.2.1 Overall Precautions When handling the hedge trimmer, follow the precautions of the powerhead manual in addition to the following precautions. Do not use the hedge trimmer when tired, ill, or after consuming alcohol, drugs, or medication. Be sure to firmly tighten the knob bolt at the attachment connection between the powerhead and the extension pipe before using the attachment. * The attachment could come off, resulting in serious injury or death.
Wear goggles meeting the requirements of ANSI Z87.1 when using the hedge trimmer. Also use a face shield (or face screen) if possible. * Failure to use goggles or face shield, could result in eye injury from flying debris. Wear hearing protective equipment such as ear protections when using the hedge trimmer. 1.2.3 Precautions before Operation Do not allow children or animals to enter the working range of the hedge trimmer within 50 ft (15 m). Do not operate the hedge trimmer near the electric wires.
1.2.4 Precautions at Start-up The hedge trimmer must only be started and operated by one person. * Operation by more than one person increases the likelihood of mishandling and resulting injury. Always start the hedge trimmer in an open, flat area with the trimmer blade off the ground. * Otherwise, you risk injury from falling or hitting the trimmer blade on the ground or obstacles. 1.2.
When trimming higher than the eye level, frequently check for obstacle in the hedge. * If the check is neglected, the hedge trimmer could make contact with a person or obstacle, resulting in serious injury or death. Remove obstacles, and watch your step when transporting the hedge trimmer. * If the footing is insecure, an injury due to tripping over or falling could happen. When turning around or rearranging your posture, the operator should move slowly.
1.2.7 Precautions for Transporting Before transporting the hedge trimmer, stop the engine, and ensure the blade has stopped. Install the trimmer blade guard on the trimmer blade. Note ●● When transporting the hedge trimmer, install it to a harness or keep it balanced by holding the shaft tube. ●● Before transporting the hedge trimmer on the back of the truck, etc., remove the attachment from the powerhead, install the guard on the trimmer blade, and then secure it so it does not move. 1.2.
1.3 Safety Devices and Protective Guard 1.3.1 Safety Devices (Stop Devices) To stop the hedge trimmer in case of an abnormality, use the stop device on the powerhead to stop blade rotation. Refer to the powerhead manual for details. 1.3.2 Safety Devices (Quick Release) In case of an abnormality, the hedge trimmer can be released from the harness by using the quick release device. Refer to the powerhead manual for details. 1.3.
1.4 Protective Equipment When using the hedge trimmer for cutting, it is recommended to wear the following protective equipment. (a) Hard hat (b) Working wear (long sleeve jackets and fulllength pants of heavy material) (c) Protective shoes (sturdy boots with nonslip sole) (Steel-toed safety boots are recommended.) Hard hat Goggles Ear protection Face shield (d) Gloves (heavy-duty, nonslip gloves) Working wear (e) Goggles that meet the requirements of ANSI Z87.1.
2. Outline 2.1 Name of Parts and Their Functions The hedge trimmer is a device with the attachment installed to the powerhead (separately sold). The following is the structure of the attachment and name and function of each part. Note ●● There is one type of powerhead. For details about the powerhead, refer to the powerhead manual. ■ SSHH-S 6 7 5 8 4 3 1 No. Name 2 Description 1 Trimmer blade A steel blade to cut the hedges or low trees.
2.2 Specification ■ Standard Specification Item Specification Model SSHH-S (short shaft) Attachment weight SSHH-S: 4.8 Ib (2.2 kg) Dimension (L x W x H) Short shaft: 35.2 x 4.9 x 4.9 in Weight Short shaft: 4.8 lbs (2.2 kg) Shaft length Short shaft: 5.3 in (135 mm) Cutter type Double-sided, Double-reciprocating Blade length 21.6 in (550 mm) Articulation angle increment 18 deg. Total articulation range Short shaft: 108 deg. (-54 to +54) 2.
2.4 Position of Model and Serial No. Check the model code of your attachment on the nameplate attached to the machine shaft. Record serial No. (See “9. Servicing”). You will need this model code and serial No. when ordering parts, and when making technical or warranty inquiries. ■ SSHH-S Note ●● The model code is 4 letters. The model code is different from the model name. xxxxxxxᲵSerial No. 2.5 Replaceable Items The following are some common replaceable items for this attachment.
3. Installation and Adjustment 3.1 Installation Method Before installing or removing any attachment or part, stop the engine and, if attached, let the trimmer blade come to a complete stop. * If the engine starts during the work, hands or fingers could be severed by the moving parts or trimmer blade. When handling the trimmer blade, wear gloves. * If you touch the edge of the trimmer blade or tip of the sharp blade, it could cause injury to hands or fingers. 3.1.
3.1.2 Connecting 1 Loosen the knob bolt [1] of powerhead connections. [1] [4] 2 Align the boss (protrusion) [2] at the end of the pipe with the slit of the joint case [3], and insert it to the label [4] [3] [3] [2] position. 3 Make sure that the positioning knob [5] is lowered to the locked position as shown, and then tighten the knob bolt [1] of the powerhead connections.
3.1.3 Removing 1 Loosen the knob bolt [1] of powerhead connections. [1] 2 3 Lift the positioning knob [5], and turn it 90°, either clockwise or counterclockwise. [5] Pull out the shaft tube [6]. If the shaft tube is hard to remove, hold [5] it so that the attachment is parallel to the pipe of the powerhead, and then pull it out. 4 Turn the positioning knob [5] until it comes to the center and locks in place. When the positioning knob [5] is returned to the center, it will be released downward.
3.2 Adjustment of Cutter Bar Angle On this type of cutter bar, the angle relative to the cutter bar can be adjusted to 7 positions between -54°to +54°. Adjust as follows. 1 Before this adjustment, stop the engine. 2 Lay down the hedge trimmer on the ground, and install the guard [1] to the [1] trimmer blade. 3 Slide the lock lever [2] to release the lock. (Remove the pin [3] of the lock lever from the hole.) [2] If it does not move smoothly, move the shaft tube [4] back and forth a little.
4. Operation 4.1 Transporting Method When transporting the hedge trimmer, wear appropriate clothes and personal protective equipment. * Otherwise, it could cause injury. Before transporting the hedge trimmer, stop the engine, and ensure the blade has stopped. Install the trimmer blade guard on the trimmer blade. Remove obstacles, and watch your step when transporting the hedge trimmer. * If the footing is insecure, an injury due to tripping over or falling could happen.
4.2 Pre-operation Check Make sure that the hedge trimmer is operated normally or there is not any part missing or damaged before starting the operation. Before operating the hedge trimmer, check the following. (a) If any part is damaged or worn out, replace before using. Contact your service dealer for a replacement part. ●● Check to see if there is any looseness, cracks, bending, or distortion of parts (nuts, screws, etc.) ●● Check to see if the trimmer blade is damaged.
4.3 Start and Stop The hedge trimmer is operated by the powerhead. Refer to the powerhead manual. 4.3.1 Start The hedge trimmer must only be started and operated by one person. * Operation by more than one person increases the likelihood of mishandling and resulting injury. For starting the hedge trimmer, refer to the powerhead manual. 4.3.2 Stop When the throttle trigger is released, the engine power will decrease, and the trimmer blade will come to a stop.
4.5 Precautions for Operation When operating the hedge trimmer, observe the following as well as “1.2 General Precautions”. ■ General ●● The hedge trimmer is not insulated against electric shock. Have a person qualified for electric work remove wires and cables. If there are still wires or cables not removable, do not operate the hedge trimmer. ●● Do not cut any materials other than hedges or shrubs.
4.6 Operation Method Do not allow children or animals to enter the working range of the hedge trimmer within 50 ft (15 m). The hedge trimmer must only be started and operated by one person. * Operation by more than one person increases the likelihood of mishandling and resulting injury. When using multiple hedge trimmers at the same time, each operator must be at least within 50 ft (15 m) away from the others. The following shows examples of use of the hedge trimmer.
■ Examples of Use Use an angled cutter bar. Use a straight cutter bar. Cut without standing directly in front of the hedge in case of cutting reaching over flower beds. Large working radius is obtained even without additional aids. Use a straight cutter bar. Cut without standing directly in front of the hedges, reaching over flower beds, ditches, etc. Note ●● Do not throw cuttings in the garbage can. They can be composted.
4.7 Actions after Operation After using the hedge trimmer, take the following actions. 1 Set the start/stop switch to OFF (O side) to stop the engine. Note ●● Make sure that trimmer blade rotation has come to a complete stop, before setting the unit down. 2 Tighten all the nuts, bolts, and screws other than the ones for adjusting the carburetor. 3 Store the hedge trimmer according to “6. Storing”.
5. Maintenance Before performing maintenance, repair or cleaning, stop the engine and remove the attachment from the powerhead. * If the engine starts during the work, hands or fingers could be severed by the moving parts or trimmer blade, resulting in serious injury or death. When handling the trimmer blade, wear gloves. * If you touch the edge of the trimmer blade or tip of the sharp blade, it could cause injury to hands or fingers.
5.1 Daily 5.1.1 Inspection of Blade If the trimmer blade is excessively worn, bent or damaged, replace the trimmer blade assembly with a new one. * Otherwise, pieces of the damaged trimmer blade could scatter, resulting in serious or fatal injury. If the cutting performance has deteriorated, e.g. the trimmer blade is frequently jammed by branches, sharpen or replace the trimmer blade. 1 Make sure that any branches or leaves are not caught by the trimmer blade.
5.2 Every 25 hours 5.2.1 Greasing the Transmission Case 1 Remove the plug [1] from the grease filler opening with the specialized tool attached to powerhead. 2 Grease from the grease filler opening [1]. 3 Refit the plug [1] of the grease filler opening with the specialized tool attached to powerhead. [1] Note ●● Do not discard grease into the river, the sea, or the ground. Otherwise, it could pollute the environment. ●● Use a specified grease (general purpose No. 2 lithium grease).
5.3 As Necessary 5.3.1 Removal of Foreign Objects Remove the stains from the trimmer blade with a cloth, etc. Clean the trimmer blade as necessary, and then apply oil thinly. Note ●● Be sure to clean the trimmer blade. If it is not cleaned, dust, wood chips, grease, etc. will be accumulated and hardened, by which the hedge trimmer is not able to be operated for the next time. 5.3.
6. Storing When storing the attachment with the hook of the pipe cap attached to the pipe, etc., do not pull or swing the attachment. When handling the trimmer blade, wear gloves. * If you touch the edge of the trimmer blade or tip of the sharp blade, it could cause injury to hands or fingers. When storing the hedge trimmer attachment, install the trimmer blade guard on the blade and place it out of the reach of children. Note ●● Do not discard grease into the river, the sea, or the ground.
7 Install the trimmer blade guard [4].
7. Waste Disposal For disposal, observe the standards and regulations of your region. If there is any question, contact your servicing dealer. 8. Troubleshooting In case of failure, follow the table below. When troubleshooting, stop the engine and then remove the attachment from the powerhead. * Situation Output is not enough. Vibration is too large. Blade is dull Trimmer blade does not move even if the engine speed is increased.
9. Servicing For repair, handling method or cleaning, contact your servicing dealer. ■ When Requesting for Repair If there is any problem, try finding the cause and take measures according to “8. Troubleshooting”. If it does not solve the trouble, contact your servicing dealer. ■ Contact for Repair Contact your servicing dealer for repair. Record serial No. (See “2.4 Position of Model and Serial No.”) in the space below. You will need this model code and serial No.
10. Technical data Model Powerhead Handle a) SSHH-S UMC425A UMC435A LOOP LOOP Mass (without guard and powerhead) lb (kg) 4.8 (2.2) Length (without guard and powerhead) in (mm) 35 (895) Cutting attachments (diameter for blades) in (mm) 22 (550) Dimension (L x W x H) in (mm) 35.2 x 4.9 x 4.9 (895 x 125 x 125) Weight Shaft length lb (kg) 4.8 (2.2) in (mm) 5.3 (135) b Cutter type Double-sided, Double-reciprocating c Blade length in (mm) 21.
MEMO 36
How to Contact Honda Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Distributor’s Limited Warranty NIKKARI ATTACHMENTS This warranty is limited to the following Nikkari products when distributed by American Honda Motor Co., Inc., Power Equipment Division, 4900 Marconi Drive, Alpharetta, Georgia 30005.
PRODUCT REGISTRATION Thank you for choosing Honda. To ensure you receive important service information in the event of a product update or recall, please register your hedge trimmer within 30 days of purchase. From time to time, American Honda conducts sales promotion that require you to register your hedge trimmer within 30 days of purchase. If you purchased your Honda hedge trimmer during one of these promotions, you must register your hedge trimmer within 30 days.
1. Go to www.PowerEquipment.Honda.com to register your unit. 2. Click on Product Registration. 3. Complete the required information and click Submit. It's that simple! NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES Product Registration BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO. 117 ALPHARETTA GA POSTAGE WILL BE PAID BY ADDRESSEE Power Equipment Division American Honda Motor Co. Inc.
