20 06652 0030 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. B. Leg 4 pcs. C. Stretcher 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the nuts may need to be tightened in the future.
Assembly Instructions 3/3 STEP 2 Place Top (A) upside down on a soft cloth. Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 2) Cap Nut Spring Washer Flat Washer Bolt Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. A Figure 2 Cover STEP 3 Turn table over to its upright position. Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06652 0080 Arm Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Back 1 pc. B. Seat 1 pc. C. Side Frame 1 pc. D. Side Frame 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the bolts may need to be tightened in the future. STEP 1 Place Side Frame (C) on a soft cloth.
Assembly Instructions 3/3 STEP 3 Turn unit to its upright position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06654 0032 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. B. Leg 4 pcs. C. Stretcher 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the nuts may need to be tightened in the future.
Assembly Instructions 3/3 STEP 2 Place Top (A) upside down on a soft cloth. Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 2) Cap Nut Spring Washer Flat Washer Bolt Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. A Figure 2 Cover STEP 3 Turn table over to its upright position. Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06654 0053 Swivel Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List B. Connector 1 pc. C. Base 1 pc. A. Back 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the bolts may need to be tightened in the future. STEP 1 A Attach Seat (A) to Connector (B) with Bolts, Flat Washers, Spring Washers and Nuts, tightening bolts and nuts only halfway.
Assembly Instructions 3/3 C STEP 2 Place unit onto Base (C).
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.