0 legit 2005170 0851 lifestyles Daybed IMPORTANT Carefully remove all the parts from the carton and place therm individually on a soft cloth to prevent scratches or other damage. Carefully and strictly fol ow these assembly instructions to ensure a completed product as designed. De not use power tools above 8 volts to assemble. Part List A Back Panel K. 1 pe.
( Assembly Instructions 2/9 ) IMPORTANT » Use a soft cloth between these parts and the floor. + Do not use power tools above 8 volts to assemble. » Do not tighten all the screws unt] each part 's properly assembled, Tha unit must be level to work properly. Use the included adjustable levelers to level. = Esp Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Insert Bolts into per-drilled holes in Posts (D), {(E, (F) | and {G}, then tighten. Attach Feet {0} to Posts (D), (E), (7) and {G).
( Assembly Instructions 3/9 ) STEP 3 Insert Cam Lock Screws into per-drilled holes in Back Pane! (B} and Front Rails {K), (1), then tighten. Figure 2 STEP 4 Attach Front Rails {i and (to Middle Panel (J) with Cam Locks. {See Figure 2) Ba.
( Assembly Instructions 4/9 ) STEPS Attach Posts (D) and {F)} to unit from Step 4 with Wooden Dowels, Square Washers and Nuts. Tighten Nuts with Wrench. STEP é Attach unt from Step 2 to unit from Step 5 with Cam Locks. Ba.
( Assembly Instructions 5/9 ) STEP? Attach Side Panels (C} to unit by sliding metal sleeves on Side Panels {C) root metal clips on unit. {See Figure 3) STEP 8 Insert 1 1/2" Round Head Screws inch unit, then tighten. Attach Side Panels (H) and to unit with Head Cap Bolts. Tighten Head Cap Bolts with Hex Wrench. {See Figure 4) Figure 4 Ba.
( Assembly Instructions 6/9 ) STEP 9 Attach Slat (M) to unit with 1" Round Head Screws into per-drilled holes in unit, STEP 10 Level unit by adjusting the adjustable levelers on bottom of unit. {See Figure 5) BC Note: Unit must be level to work properly. Figure 5 Ba.
( Assembly Instructions 7/9 ) Drawer (N) rz STEP 11 , a. Attach Drawer Sides (N3) and {N4} to = Drawer Front (N1) and Drawer Back (N2) ~ with 1 1/4" Flat Head Screws. md 1 1/4" Flat Head Serena a 1/2" Round Head re Insert Drawer Bottom (N5) into groove. STEP 12 Attach Drawer Bottom (N5} to unit with 1/2" Round Head Screws. Attach Drawer Supports (N6) to unt with 11/4" Flat Head Screws. 1174" Fiat Head Craw Machine Screw STEP 13 Attach Handles with Machine Screws.
( Assembly Instructions 8/9 ) STEP 14 Loosen slightly the screws per-installed on back of drawer fronts. Hu STEP 15 Align metal runners on sides of Drawers (N} into metal guides on unit and slide Drawers (N) nto unit. Adjust drawer front panels left or right and up or down until drawer gaps lock proportional. STEP 16 Pull each drawer open slowly and re-tighten screws from Step 14.
( Assembly Instructions 9/9 ) STEP 17 Lock each drawer front panel into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly. 374" Fiat Head Screw 3/4" Flat Head Sorrow STEP 18 Align metal runners on sides of Drawers {N} into metal guides on unit and slide Drawers {N} into unit. Ba.
