Instructions / Assembly

ManualsBrandsHome Styles ManualsDecorNantucket Maple Food Pantry

Part List

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damages occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure

a completed product as it was designed.

Hardware List

Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319

servicedesk@homestyles-furniture.com

Side Panel

1 pc.

Side Panel

1 pc.

Pantry

Side Panel

1 pc.

Side Panel

1 pc.

Stretcher

1 pc.

Stretcher

2 pcs.

Back Stretcher

4 pcs.

Back Stretcher

2 pcs.

Back Panel

4 pcs.

Top

1 pc.

Base

1 pc.

Shelf

4 pcs.

Door

1 pc.

Door

1 pc.

Door

1 pc.

Door

1 pc.

Drawer

1 pc.

(Knock-Down Construction, please refer

to the last page of these instructions for

drawer assembly steps)

Cam Lock

30 pcs.(+4 extra)

Cam Lock Screw

30 pcs.(+1 extra)

M4x25

Machine Screw

8 pcs.

Adjustable Pin

16 pcs. (+1 extra)

Knob

4 pcs.

M3.5x16

Wood Screw (short)

22 pcs. (+1 extra)

M3.5x25

Wood Screw (long)

for Drawer Side Part

8 pcs. (+1 extra)

Pull Handle

2 pcs.

Top

1 pc.

Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level

88 5055 69

Summary of content (7 pages)

PAGE 1
88 5055 69 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List A. Top 1 pc. B. Side Panel 1 pc. F. Stretcher 1 pc. C. Side Panel 1 pc. D. Side Panel 1 pc. H. Back Stretcher 4 pcs. G.
PAGE 2
Assembly Instructions 2/7 IMPORTANT * Do not tighten up all the screws until each part is properly assembled. * You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * After assembly, item must be level to work properly. Use the included adjustable levelers to level. Cam Lock Screw E D C B A K L Cam Lock Screw STEP 1 Put Cam Lock Screws into the pre-drilled holes of Top (A), (K) Side Panels (B),(C), (D), (E) Base (L) and tighten.
PAGE 3
Assembly Instructions 3/7 C STEP 2 Attach Stretcher (F), (G) and Back Stretcher (H) to Side Panel (B) using Cam Locks. Attach Back Stretcher (I) to Back Stretcher (H). Slide Back Panels (J) into place. F G H J I Attach Back Stretcher (H) to unit using Cam Lock. H J Attach Side Panel (C) to unit using Cam Locks. Cam Lock B STEP 3 Attach unit from Step 2 to Base (L) using Cam Locks.
PAGE 4
Assembly Instructions 4/7 K STEP 4 Attach Door (P) and (Q) to unit by sliding the door lift hinges into the Side Panel lift hinges. (see Figure 1) P Attach Top (K) to unit using Cam Locks. Q Cam Lock (Figure 1) E Cam Lock STEP 5 J Attach Stretcher (G) and Back Stretcher (H) to Side Panel (D) using Cam Locks. I Attach Back Stretcher (I) to Back Stretcher (H). H H G J Slide Back Panels (J) into place. Attach Back Stretcher (H) to unit using Cam Lock.
PAGE 5
Assembly Instructions 5/7 A STEP 6 Attach unit from Step 5 to Top (K) using Cam Locks. Attach Door (N) and (O) to unit by sliding the door lift hinges into the Side Panel lift hinges. N Place Top (A) onto unit using Cam Locks. O K (Figure 3) (Figure 2) Adjustable Pin Cam Lock M Wood Screw (short) N M O (Figure 4) Attach the Door Knobs to Doors (N), (O), (P) and (Q) using Machine Screws. (see Figure 2) R P STEP 7 Insert the Adjustable Pins into both Side Panels at the desired level.
PAGE 6
Assembly Instructions 6/7 Attention! To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly! Wall Screw Anchor in wall 3/8” wall hole Bracket on wall Wood Screw Place unit at desired location. Drill a 3/8” hole in wall at the appropriate location. Insert Anchor into the wall hole and attach Bracket with Wall Screw. Attach Bracket at pre-drilled hole at top of unit with Wood Screw.
PAGE 7
Assembly Instructions 7/7 Drawer R1 R3 (Figure 1) STEP 1 Attach R1 to R3 and R4, using a Phillips screwdriver and long wood screws (4X), tighten halfway. R2 R4 Attach R2 to R3 and R4 using long wood screws (4X), tighten halfway. (see Figure 1) MAKE SURE ROLLER IS ON THE BACK STEP 2 Slide R5 into the grooves in R3 and R4. Be sure to push R5 all the way forward to it meets R1.