Installation Manual

ManualsBrandsHome Styles ManualsFurnitureHome Styles Patriot Kitchen Cart, White

88 4514 95

Kitchen Cart

Home Styles Consumer Assistance : www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319

Hardware List

Part List

IMPORTANT NOTE

Tools required for assembly : Phillips screwdriver

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damage occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure

a completed product as it was designed.

Side Panel

1 pc.

Side Panel

1 pc.

Middle Panel

1 pc.

Middle Panel

1 pc.

Back Upright

2 pcs.

Back Panel

3 pcs.

Front Stretcher

1 pc.

(Please refer to the last page of these

instructions for drawer assembly steps.)

Shelf

4 pcs.

Door

1 pc.

Door

1 pc.

Tower Bar

1 pc.

Arm

2 pcs.

Rack

1 pc.

Base Rack

1 pc.

Side Rack

1 pc.

Side Rack

1 pc.

Top

1 pc.

Base

1 pc.

Back Stretcher

1 pc.

Back Stretcher

1 pc.

Pull Handle

4 pcs.

Cam Lock

22 pcs. (+6 extra)

Caster

2 lock

2 non-lock

4 pcs.

Cam Lock Screw

22 pcs. (+2 extra)

M4x32

Wood Screw

8 pcs. (+1 extra)

M3x16

Wood Screw (short)

for Drawer Base Part

and Back Panel

20 pcs. (+1 extra)

Magnet

2 pcs.

Drawer

2 pcs.

M3x16

Wood Screw

for Magnet

4 pcs. (+1 extra)

M3.5x25

Wood Screw (long)

for Drawer Side Part

24 pcs. (+1 extra)

M4x25

Machine Screw

8 pcs.

Adjustable Pin

16 pcs.

Flat Washer

8 pcs. (+1 extra)

Hex Wrench

1 pc.

Small Wrench

1 pc.

M6x12

Head Cap Bolt

for Caster

16 pcs. (+1 extra)

M6x25

Head Cap Bolt

4 pcs. (+1 extra)

Summary of content (6 pages)

PAGE 1
88 4514 95 Kitchen Cart IMPORTANT NOTE. Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List A. Top 1 pc. U. Base 1 pc. B. Side Panel 1 pc. C. Side Panel 1 pc. F. D. E. Middle Panel Middle Panel Back Panel 3 pcs.
PAGE 2
Assembly Instructions 2/6 IMPORTANT * Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Do not tighten up all the bolts until each part is properly assembled. * Use a soft cloth between these parts and the floor. B STEP 1 C Insert Cam Lock Screws into pre-drilled holes of Top (A), Side Panels (B), (C), Middle Panels (D), (E) and Base (U). (See Figure 1) A Cam Lock Screw Attach Magnets to Top (A) with Wood Screws for Magnet.
PAGE 3
Assembly Instructions 3/6 Head Cap Bolt N Head Cap Bolt P K O K B C Figure 4 M Figure 5 STEP 3 Attach Arms (K) to Side Panel (B) with Head Cap Bolts. (See Figure 4) Assemble Side Racks (M), (N), Base Rack (O) and Rack (P), then attach to Side Panel (C) with Head Cap Bolts. (See Figure 5) Cam Lock H B F F F G I G C STEP 4 Attach Back Stretcher (I) to Side Panel (B) with Cam Lock. (See Figure 6) Attach Back Uprights (G) to unit, then slide Back Panels (F) into position.
PAGE 4
Assembly Instructions 4/6 Cam Lock J D E STEP 5 Attach Middle Panels (D) and (E) to Front Stretcher (J) with Cam Locks. Attach unit and unit from Step 4 to unit from Step 2 with Flat Washers and Wood Screws. Flat Washer Wood Screw H L Wood Screw (short) Cam Lock I STEP 6 Turn the unit to its’ upright position. Insert Wood Screws (short) and Cam Locks into pre-drilled holes of Back Stretchers (H) and (I) and tighten. Slide Tower Bar (L) into place.
PAGE 5
Assembly Instructions 5/6 A Cam Lock Adjustable Pin R S Q T Q Q T Q STEP 7 Attach Pull Handles to Doors (R) and (S) with Machine Screws. (See Figure 7) Attach Doors (R) and (S) by sliding the door life hinges to side panel lift hinges. (See Figure 8) Attach Top (A) to unit with Cam Locks. Insert Adjustable Pins into side panels and middle panels at the desired level, then place Shelves (Q) into position. Slide Drawers (T) into position.
PAGE 6
Assembly Instructions 6/6 Drawer T T1 T3 STEP 1 Attach T1, T3 and T4 using a Phillips screwdriver and long wood screws (6X), tighten halfway. T4 T2 Figure 1 Attach T2, T3 and T4 using a Phillips screwdriver and long wood screws (6X), tighten halfway. (See Figure 1) MAKE SURE ROLLER IS ON THE BACK STEP 2 T1 T3 Slide T5 into groove of T3 and T4. Be sure to push T5 all the way forward so it meet T1.