Instructions / Assembly

ManualsBrandsHome Styles ManualsCarts, Islands & Utility TablesLiberty Black Kitchen Cart

PART LIST

HARDWARE LIST

Adjustable Pin

8 pcs. (+1 extra)

M4x25

Machine Screw

5 pcs.

Top

1 pc.

Side Panel

1 pc.

Side Panel

1 pc.

Back Panel

3 pcs.

Middle Panel

1 pc.

Back Stretcher

1 pc.

Back Upright

2 pcs.

Side Rack

1 pc.

Side Rack

1 pc.

Rack

1 pc.

Base Rack

1 pc.

Base

1 pc.

Caster

2 lock

2 non-lock

4 pcs.

Arm

2 pcs.

Drawer

Pull Handle

5 pcs.

88 4513 95

Kitchen Cart

Tools required for assembly : Phillips screwdriver

Home Styles Consumer Assistance: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damages occurring to the wood parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure a

completed product as it was designed.

Back Stretcher

1 pc.

Towel Bar

1 pc.

M3x16

Wood Screw

for Magnet

4 pcs. (+1 extra)

Magnet

2 pcs.

M3.5x25

Wood Screw (long)

for Drawer Side Part

24 pcs.(+1 extra)

M3.5x16

Wood Screw (short)

for Drawer Base Part

and Back Panel

24 pcs. (+1 extra)

Hex Wrench

1 pc.

Small Wrench

1 pc.

M6x12

Head Cap Bolt

for Caster

16 pcs. (+1 extra)

M6x25

Head Cap Bolt

4 pcs. (+1 extra)

M6x38

Head Cap Bolt (long)

4 pcs. (+1 extra)

Shelf

2 pcs.

Door

1 pc.

Door

1 pc.

Drawer

3 pcs.

(Please refer to the last page of these

instructions for drawer assembly steps.)

Front Piece

2 pcs.

Summary of content (6 pages)

PAGE 1
88 4513 95 Kitchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. PART LIST A. Top 1 pc. B. Side Panel 1 pc. C. Side Panel 1 pc. D. Middle Panel 1 pc. G. Back Stretcher 1 pc. E. F.
PAGE 2
Assembly Instructions 2/6 IMPORTANT * Do not tighten up all the screws until each part is properly assembled. * Use a soft cloth between these parts and the floor. STEP 1 Attach 2X Magnets to Top (A) by using Wood Screws (for Magnet) into the pre-drilled holes. (See Figure 1) Figure 1 C Wood Screw (for Magnet) Magnet A B Head Cap Bolt N Head Cap Bolt P K O K B Figure 2 C M Figure 3 STEP 2 Attach Arms (K) to Side Panel (B) with Head Cap Bolts.
PAGE 3
Assembly Instructions 3/6 H Figure 4 E F E E F C B Figure 5 G STEP 3 Attach Back Stretcher (G) to Side Panel (B), then filp the Locks. (See Figures 4 and 5) Attach Back Uprights (F) and slide Back Panels (E) into position. Attach Back Stretcher (H) and Side Panel (C) to unit, then filp the Locks. Figure 6 Non-Locking Caster Head Cap Bolt (for Caster) J STEP 4 Locking Caster Attach 4 Casters underneath Base (J) with Head Cap Bolts (for Caster), put 2 Casters with Lock at the front side.
PAGE 4
Assembly Instructions 4/6 Head Cap Bolt (long) STEP 5 Attach base unit to unit with Head Cap Bolts (long). L G D I Wood Screw (short) STEP 6 I Turn the unit to its’ upright position. H Slide Towel Bar (L) into place. Attach Front Pieces (I) and Middle Panel (D) to unit from Step 3, then filp the Locks. Insert Wood Screws (short) into the pre-drilled holes of Back Stretchers (G) and (H) and tighten.
PAGE 5
Assembly Instructions 5/6 A Q T R S T S Adjustable Pin T STEP 7 Insert Adjustable Pins into side panel and middle panel at the desired level. Place Shelves (S) into position. Attach Doors (Q) and (R) by sliding the door lift hinges into the side panels lift hinges. (See Figure 7) Figure 7 Assemble Pull Handles to Doors with Machine Screws. (See Figure 8) Attach Top (A) to the unit, then filp the Locks. Slide Drawers (T) into position.
PAGE 6
Assembly Instructions 6/6 Drawer (T) STEP 1 T3 Attach T1 to T3 and T4, using a Phillips screwdriver and long wood screws (4X), tighten halfway. T1 T4 T2 Attach T2 to T3 and T4 using long wood screws (4X), tighten halfway. (See Figure 1) MAKE SURE ROLLER IS ON THE BACK Figure 1 STEP 2 Slide T5 into the grooves in T3 and T4. Be sure to push T5 all the way forward so it meets T1.