Instructions / Assembly

ManualsBrandsHome Decorators Collection ManualsBistro SetsBrandywood 3-Piece Aluminum Woven Outdoor Bistro Set with Black Cushions

Table Of Contents

AGK14200

Page 2

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!

TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD, AND RECEIPT.

PARTS LIST DESCRIPTION ORDER PART #

QTY

HEX BOLT DRIVER

SEAT FRAME

BACK FRAME

RIGHT LEG

HW0004

HW0006

FOOT CAP

FACTORY ASSEMBLY

* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE

Ø6.5 X 1.0 MM

WASHER

FC0607

Step 4: After making any necessary adjustments to the

alignment of the chair, use the hex bolt driver to tighten

all bolts. Note: each bolt must be tightened a few

revolutions at a time. In order to apply equal pressure

to all bolt joints, we recommend working in a cross

corner (X fashion). Repeat until all bolts are tight.

Do not over tighten. Over tightening may strip bolts.

Cover all bolts with covers.

Step 5: With the help of another person, turn the chair in the

upright position. Your table is now ready for use. If

you have any questions, please call our Customer

Service Center at 1-800-416-3511.

IMPORTANT NOTE: Damage to welds or frames resulting

from over tightened bolts or improper assembly is not covered

under our warranty. Please read all instructions carefully

before assembly. If you have any questions regarding your

assembly, call our Customer Service Center at 1-800-416-3511.

Figure 2

Step 1: Remove all protective materials and set parts on a flat,

non-abrasive surface. Identify parts packed in carton

against the parts list. If you are missing any parts or are

unsure how to proceed with assembly, call our Customer

Service Center at 1-800-416-3511. Do not attempt

assembly if any parts are missing or damaged.

Step 2: Attach the seat frame to the back frame by using two

bolts and washers as shown in F 1.

Guide the bolts through the holes in the seat frame

into the pre-drilled holes in the back frame. Hand

tighten only2-3 turns.

1/4"x30 mm igure

Step 3: Attach the left leg to the seat frame & back frame by

using a bolt, three bolts, and

four washers as shown in F 2. Guide the bolts

through the holes in the seat frame & back frame, into

the pre-drilled holes in the left leg. Hand tighten

only 2-3 turns. Repeat for the right leg.

1/4"x20 mm 1/4"x30 mm

igure

1/4" X 20 MM BOLT

HW0036

Figure 1

FOOT CAP

1/4" X 30 MM BOLT

HW0038

LEFT LEG

AN0819

AN0820

AN0821

AN0822

Summary of content (2 pages)

PAGE 1
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!! TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD, AND RECEIPT. * NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE Step 1: Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts packed in carton against the parts list. If you are missing any parts or are unsure how to proceed with assembly, call our Customer Service Center at 1-800-416-3511.
PAGE 2
CARE AND MAINTENANCE FRAMES Cleaning - Use mild soap and warm water. Do not use abrasive materials, cleaners, or bleach products. Rinse with clean water and dry thoroughly. Maintenance - Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to remove all water. This is critical.