Instructions / Assembly

7.5ft GENOA EUROPEAN FIR TREE & MILES NOBLE FIR-116 Function Remote (English)
Items # 025007560030152/015007550026052
025007560030152/015007550026052
REMOTE CONTROL OPERATION
Your Pre-Shaped & Pre-lit LED Christmas Tree’s 116 Function
capability is controlled solely by the use of the remote control
provided (Fig 7).
A CR2032 Battery is included within the remote control. Before
operating the remote; remove the thin plastic film that has
been inserted - by slightly pulling downward away from the
lower portion of the remote control.
9. Once section “B” is fully inserted downward into section “A”; both
section “A” and section “B” will now be lit.
10. Again, carefully cut the nylon strapping bounding the branches
upright; being extremely careful not to cut any of the exposed
light set wires.
11. Gently guide the branches of section “B” downward into place.
12. Locate the top section of the tree which is identified by a label on
the outer branches marked “C” (Fig 5).
13. Insert the top section “C” onto the top of section “B” (Fig 5).
14. Once section “C” is fully inserted downward into section “B”; your
entire tree will now be lit.
15. Gently guide the branches of section “C” downward into place.
Fig 4
EZ-POWER™ TECHNOLOGY
Your tree has been designed with EZ-Power™ technology; allowing
for each of the tree’s sections to light up automatically, upon a
firm insertion of each lettered section (Fig 5).
7. Locate the next section of the tree which is identified by a label on
the outer branches marked “B” (Fig 5).
8. Remove the protective plastic cap from the end of the pole on
section “B”; insert that end onto the top of the pole of section “A”
(Fig 4).
A
B
C
Foot Pedal
Fig 5
ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified by a
label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap from the end of the pole, and
place that end into the tree stand. Be sure that the pointed end
of the pole extends to the bottom of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being careful
not to over-tighten (Fig 3).
ASSEMBLY INSTRUCTIONS
(We recommend wearing proper clothing in order to prevent scratches
that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1).
Your tree will include the following components:
• A folding metal tree stand with (3) eyebolts.
• An on/off push button foot pedal with cord and plug (Fig 6); which is
pre-attached to your tree (Fig 5).
• (3) tree sections - labeled “A”, “B” and “C”, as shown in Fig 5.
• Contained in the poly-bag adhered to the interior flap of the carton is
the remote control which operates your tree's 116 function lighting
capability; along with replacement bulbs.
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye bolt
and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2) eyebolts.
3. Insert each eyebolt and begin threading in a clockwise direction
for a couple of rotations only; leaving enough room for the tree’s
pole from section “A” to be inserted into the assembled stand (Fig
2).
4. Place the tree stand in its desired location; as once the tree is fully
assembled, it may be too difficult to move and relocate.
Fig 2
Fig 3
4. Carefully cut the nylon strapping bounding the branches upright if
applicable.
CAUTION: Be extremely careful not to cut any of the exposed light
set wires.
5. Gently guide the branches downward into place.
6. Beneath the canopy of section “A”, is the on/off push button foot
pedal with cord and plug (Fig 6).
Remove the twist-tie binding the cord together and insert the plug
into a working electrical outlet. Section “A” will now be lit. If section
“A” fails to light - press the On/Off push button foot pedal (Fig 5) -
as it may be in the “Off” position.
On/Off push button foot pedal operation:
The on/off push button foot pedal is intended to provide basic
manual on/off operation only; and therefore cannot provide the
remote control 116 function lighting capability.
Fig 1
Fig 6
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓ ✓ ✓
1. Warm White
2. Cool White
3. Red
4. Green
5. Blue
6. Purple
7. Teal
8. Multi
9. Red/Green
10. Blue/Cool White
11. Red/Cool White/Blue
12. Red/Warm White
13. Green/Warm White
14. Red/Green/Warm White
Total no. of functions
Brightness control
Steady Glisten Firefly Twinkling Random
Twinkle
Chasing 2 Color
Variable
Fireworks
14 14 14 14 14 14 14 14 1 1 1
Yes Yes No No Yes Yes No No No No No
7 Color
Morphing
7 Color
Slow fade
Demo
✓
1
No
Cycle
Favorite
Color / Function
116 LIGHTING COMBINATIONS:
Chasing
Fireworks
7 Color
Slow Fade
7 Color
Morphing
2 Color
Variable
Select
Favorite
Play
Favorite
Random
Twinkle
Cycle
Favorite
Glisten FireflySteady
Demo
Twinkling
Fig 7
IMPORTANT: “HOME MODE” Activation of your
Remote Control.
• Press the and at the same time.
• The Tree will flash MULTI color twice to activate.
• This double flashing of the MULTI color allows you to now operate the
remote control manually.
• Please Note: If you again press these two buttons simultaneously;
(whereas the tree would flash MULTI just once), the tree would now be in
“Store Mode” – Causing the tree to automatically default to the “Demo”
function (after remaining in idle for just 3 minutes) – Cycling
through ALL of the trees 116 available color & lighting function combinations.
SELECTING A COLOR:
• First select a desired lighting function; Choose on your remote from Steady,
Glisten, Firefly, Twinkling, Random Twinkle, Chasing, 2 Color Variable and
Fireworks Functions.
• By repeatedly pressing the button of your preferred selected function; you
will scroll through the 14 available color & color combination choices.
• Example: (Per the Chart below) Press the “Twinkling” function button once
for Twinkling “Warm White”, press again for Twinkling “Cool White”, press
again for Twinkling “Red” and so on.
SELECTING A FUNCTION:
• As indicated in the “Selecting a Color” section above; simply press a
desired lighting function button - Per the 12 individual lighting functions
available.
DISASSEMBLY & STORAGE
1. Gently remove the plug from its electrical outlet, and carefully bind the cord
which contains the on/off push button foot pedal and plug.
2. Beginning with the tree’s top section; lift each section straight up from the
section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift each section
upward.
3. To remove the bottom and final section; loosen the eyebolts by turning in a
counter-clockwise direction and lift section “A” from the support collar of
the tree stand.
4. Gently fold the branches of each section upward, towards the center, and
position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding each section
upside down; the branches will collapse downward, due to the hinging,
aiding in the packing of each section into the storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold together; placing
in the storage container.
6. It is recommended to always store the tree in a cool, dry location protected
from excessive exposure to heat or sunlight.
NOTE: Store your remote control in a SAFE & DRY location and remove the
battery from remote control before storage.
NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE RATED FOR
INDOOR OR OUTDOOR USE; THE COMBINATION OF THE TREE WITH THE LED
LIGHTS IS FOR INDOOR USE ONLY.
SPECIAL FEATURES:
BRIGHTNESS CONTROL:
• Press the “Brightness” button 3 times; to achieve your preferred level of
brightness – Select either a low, medium or high brightness level.
• Please Note: Per the chart below; the brightness control is ONLY available
on 4 of the 12 available functions - “Steady”, “Glisten”, “Random Twinkle”
and “Chasing” functions only.
TIMER FEATURE:
• Press the “Timer” button; the trees lights will flash GREEN 3 times –
Indicating that the 6 hour “On” / 18 hour “Off” timer has now been activated.
• Note: The tree’s lights will automatically resume back to the “On” position –
24 hours from when it was initially activated.
• Press the “Timer” button again, the trees lights will flash RED 3 times –
Indicating that the timer feature has now been deactivated.
• Note: The trees On/Off operation is now controlled by either the manual
operation of the remote control or by foot-pedal control.
Select
Favorite
SELECT A FAVORITE:
• Press the “Select Favorite” button if you wish to store a favorite color or
function combination.
• You are able to record & store up to 5 of your “Favorites” – For future
viewing – by pressing the “Play Favorite” & “Cycle Favorite” buttons located
on your remote control.
• Note: The trees lights will flash BLUE 3 times – indicating a successful
recording of a “Favorite”.
Play
Favorite
PLAY YOUR FAVORITES:
• Press the “Play Favorite” button to view each of your selected favorites.
• With every push of this button; you can view each previously recorded “
Select Favorite” individually.
• Note: When pressing the button for the 6th time – Your 1st recorded
selection will be on display.
• Note: If no “Favorites” have yet been selected/recorded – by the use of the
“Select Favorite” button – The trees lights will flash PURPLE 3 times –
indicating that no favorites have yet been selected/recorded.
Cycle
Favorite
CYCLE YOUR FAVORITES:
• Press the “Cycle Favorite” button to have up to 5 of your selected favorites
cycle through a personalized demonstration of ALL of your favorite color &
function combinations!
• Note: If no “Favorites” have yet been selected/recorded – by the use of the
“Select Favorite” button – The trees lights will flash PURPLE 3 times –
indicating that no favorites have yet been selected/recorded.
NOTE: If the tree is powered off by the use of the push button foot
pedal, remote control or by unplugging it from the electrical
outlet; when powered back on the tree will resume the memory of
the last lighting function selected with the remote control.
1. If the tree does not illuminate press the on/off button on your remote
control. If failure to light persists, the battery may need to be replaced.
Insert a standard CR2032 battery.
NOTE: The tree’s 116 function lighting capability is controlled solely by the use
of the remote control provided.
NOTE: By reducing the distance from your tree; you may achieve better
remote control reception.
If the tree fails to light due to a damaged or defective remote control;
please resort to manual on/off push button foot pedal operation until a
new remote control can be provided through our customer service center.
2. If failure to light persists, press the on/off push button foot pedal; as it may be in
the “Off” mode.
3. If the top of the tree or another individual lettered section does not
illuminate, remove each section and then reinsert as instructed, to ensure
the electrical connection is made.
NOTE: The tree’s top is designed specifically for a secure and firm
connection point. Downward force will be needed to ensure that the
electrical connection occurs.
TROUBLESHOOTING
Model No.
SKU No. 1004385740 / 1004200616
Made in China
Printed in China
This is not a toy, for decorative use only.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
This product was pre-tested before shipment and date coded. In keeping
with the National Electric Code, this product is intended for seasonal (90
days max.) installation and use. For problems or questions on this product
call our customer service toll-free at 1-877-527-0313.
18”
17”
2020 Home Depot.com/US
Date:02/27/20
CCT20
SKU No. 1004363849 / 1004239744